勢剪切面 的英文怎麼說

中文拼音 [shìjiǎnqiēmiàn]
勢剪切面 英文
potential shearing plane
  • 勢 : 名詞1 （勢力） power; force; influence 2 （一切事物力量表現出來的趨向） momentum; tendency 3 （自...
  • 剪 : Ⅰ名詞1 （剪刀） scissors; shears; clippers2 （姓氏） a surname Ⅱ動詞1 （用剪刀等使細的或薄片的東...
  • 切 : 切Ⅰ動詞1 （合; 符合） correspond to; be close to 2 （用在反切后頭 表示前兩個字是注音用的反切）見 ...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  1. The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film

    試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。
  2. This paper introduce simulink to simulation of structural nonlinear seismic responses innovative, working on regulation and dominance of simulation of structural dynamic response of simulink based on muti - storey shear - type model and member model, and set up basic block of structural dynamic response to pave the way for wide analysis of structural dynamic response, especially vibration control

    本文開創性地將simulink引入結構非線性地震反應模擬中，以層間剪切模型和平面桿系模型為對象，努力探討simulink用於結構動力模擬的規律並發掘其優勢，編制結構動力模擬的基礎性模塊，為逐步實現更廣泛的結構動力分析尤其是結構的振動控制奠定基礎。
  3. Firstly, with uniaxial symmetrical rectangle cross section, the warping displacement function and tangential displacement function under anti - symmetrical load are supposed. then taking shear deformation into account and with potential principle, the governing differential equation for distortion angle subjected to uniformly distributed distortion load is established

    首先，以單軸對稱矩形截面薄壁桿件為研究對象，假設其在反對稱荷載作用下翹曲位移和切向位移的分佈函數，考慮剪切變形的影響，利用最小勢能原理建立單位均布畸變荷載作用下的畸變角微分方程。
分享友人
分享到 Line

分享到臉書