噴嘴噴射角度 的英文怎麼說

中文拼音 [pēnzuǐpēnshèjiǎodù]
噴嘴噴射角度 英文
nozzle spray angle
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 射 : Ⅰ動詞1 （用推力或彈力送出） shoot; fire 2 （液體受到壓力迅速擠出） discharge in a jet 3 （放出） ...
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 角度 : 1. [數學] （角的大小） angle; the degree [size] of angle 2. （看事情的出發點） point of view; angle
  1. A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure, properties of conveyed material and driving gas. it is observed that, an increase of convergent section angle is harmful to the pneumatic conveying system, and also influences on the mass flow rate of conveyed material, the distribution of static pressures in injector and the pressure drops of conveying pipe. in addition, within a reasonable scope of air mass rate, increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle

    試驗研究發現，氣體噴嘴位置對氣固噴射器的輸送能力影響最大，氣體噴嘴存在某一最佳位置，而這一最佳位置與背壓、輸送物料特性和輸送風特性相關聯；氣固噴射器的收縮角對其輸送能力、內部靜壓分佈和輸送管阻力特性均有適量影響，收縮角增大對整個輸送系統均不利；在適當的輸送風范圍內，提高氣體噴嘴出口速度比擴大氣體噴嘴尺寸更為有利，但氣體噴嘴出口速度過高會增加氣固噴射器和輸送管內的能量損耗，給輸送帶來不利的影響；系統背壓與氣固噴射器的氣體噴嘴出口速度的選取有關。
  2. Oil pressure atomizing nozzles - determination of the angle and spray characteristics

    油壓霧化噴嘴.角度和噴射特性的測定
  3. Analyzing the finished sprinkler products in our country and overseas, testing all sorts of sprinkler parameters ( elevation of sprinkler, diameter of the nozzle, working pressure, the range of water, uniformity of spray irrigation, intensity of spray irriga tion, the degree of atomization ) so as to compare with the new style sprinkler install with pressure adjuster

    對國內和國外的一些中壓噴頭成品進行分析、研究、測試取得實際的各項參數（噴射仰角、噴嘴直徑，工作壓力、射程、噴灌均勻度、噴灌強度、霧化程度）以便和安裝「壓力調節器」后的噴頭進行比較2
  4. The influences of the inlet tube angle, backpressure and driving jet velocity on static pressure distribution in the gas - solid injector are calculated, and the effects of the inlet tube angle on particle bulk phase concentration and axial mean speed of particles in the gas - solid injector are analyzed firstly. the predicament caused by lack of measuring means on the particle velocity in experiments is solved

    分析了收縮角、背壓和氣體噴嘴出口速度對氣固噴射器內靜壓分佈的影響，以及收縮角對氣固噴射器內固體顆粒體積濃度場和顆粒平均速度的影響，解決了噴射器內固體顆粒速度試驗測試手段缺乏的困境。
  5. 3. testing all the hydraulic parameters of the sprinkler installed with adjuster such as working pressure, water flux, the range of the sprinkler, intensity of water drop impact, characteristic of water distribution, etc. according to the testing data, we can learn the quantitative relations among the structure of the adjuster, working pressure, diameter of the nozzle, elevation of sprinkler, wind power, velocity of rotation and the range of water

    測試安裝「壓力調節器」后的噴頭的水力性能參數，即工作壓力、流量、射程、水滴的打擊強度、噴灑水分佈特性等。依據所測得的噴頭水力性能參數和射程數據，我們可較清楚的了解「壓力調節器」的結構形式、工作壓力、噴嘴直徑、噴射仰角、風力、旋轉速度和噴頭射程之間的定量關系。
  6. ( 2 ) base on the analysis of the atomizing principles of spray nozzle, mathematical model of combined spin - flow pressure spray drying was set up and the essential parameters such as spraying pressure, liquid quantity, temperature, spraying angle, inject distance, particle diameter and distribution, hollow diameter for several materials in normal conditions by experiment and ldv

    （ 2 ）對旋流式組合壓力噴嘴噴射霧化機理加以分析，建立了旋流式噴嘴霧化的數學模型，採用冷態試驗法並藉助激光霧滴測試等實驗裝置對噴嘴的霧化參數（如霧化壓力、噴液量、料液溫度、霧化角、霧距、霧滴直徑和分佈以及噴嘴的空芯半徑等）進行測量和計算。
  7. En299 oil pressure atomizing nozzles. determination of the angle and spray characteristics

    油壓自動噴嘴.角度和噴射特性的測定
分享友人
分享到 Line

分享到臉書