嚙合平面 的英文怎麼說
中文拼音 [niègěpíngmiàn]
嚙合平面
英文
plane of action-
Gs series high speed involute cylindrical gear box is hard gear side box which is according to national criteria to design and manufacture. its structure form is outside engaged straight fear, oblique tooth gear or herringbone gear of single, closed and parallel axis
Gs系列高速漸開線圓柱齒輪箱是按照國際標準設計、生產的硬齒面齒輪箱，其結構形式為外嚙合的直齒、斜齒或人字齒結構，單級、閉式、平行軸傳動。On the basis of the engage efficiency and lubricious conditions, theoretical transmission efficiency with the different drive ratios ( 1 / 50 and 6 / 31 ) of involute cylinder worm gears is analyzed. at the same time, the change trend of engage efficiency and transmission efficiency with different design parameters is discussed. the experimental investigation on transmission efficiency
從漸開線蝸輪蝸桿傳動的嚙合效率和潤滑條件兩個方面對不同傳動比的漸開線圓柱蝸桿的傳動效率進行理論分析，並通過傳動比分別為1 / 50和6 / 31的漸開線圓柱蝸桿設計參數得到蝸桿潤滑條件的理論分析結果和蝸桿嚙合效率、傳動效率的變化趨勢，同時利用電測法對蝸桿傳動的傳動效率、潤滑油平衡溫度進行測試，將測試數據與理論計算結果進行對比分析，得出理論分析結果的正確性。On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs
考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示Creative points and all tasks having be finished are briefly shown below : according to the classical space meshing theory, we have strictly deduced a series of formulae such as the equation of contacting line of worm, the equation of the second limiting curve of worm gear, and the equation of working surface and non - working surface, etc. and we have deeply studied the algorism of the actual contacting lines of worm gear drive
本文的主要創新點和成果如下：基於經典共軛嚙合理論，對平面二包蝸桿副的運動關系進行了嚴密分析，獲得了蝸桿副齒面方程、蝸桿齒面一界曲線方程、蝸輪齒面二界曲線方程等一系列齒面分析所必須的數學公式，並深入研究了蝸桿副齒面接觸線的演算法，為蝸桿副的三維數字化造型打下了堅實的數學基礎。It was pointed out that the actual center - line and theoretic meshing line of the paired gears varied in the form of planar motion due to the system vibration, and the actual meshing line was curvilinear
結果表明，由於系統振動的原因，齒輪副的實際中心線和理論嚙合線是以平面運動方式變化的，實際嚙合線（即嚙合點的軌跡）是一條曲線。The states of motions and victories and forces of the worm engaging point were been analysis. the motions and forces of the worm engaging point have been initiate by the program with matlab. the 3d motions of plane double enveloping worm has been emulated with solidege and flash
應用solidege三維實體造型軟體，進行平面二次包絡環面蝸桿傳動的運動狀態的動態模擬，模擬了平面二次包絡環面蝸桿傳動的運動狀態，再現了蝸桿嚙合的運動狀態的模擬。Flat disc. floating stem - disc engagement, hardfaced with 13 cr, stellite 6, ss 316 or monel, ground and lapped with seat. disc in ss 316 hardfaced with stellite 6 also available
平面閥瓣。浮動的閥桿-閥瓣嚙合， 13cr 、鎢鉻鈷合金6 、不銹鋼316或蒙乃爾表面硬化、研磨拋光的閥座。表面鎢鉻鈷合金6硬化的316不銹鋼閥瓣也可供用戶選擇。This thesis reviewed the mesh theory of plane double - enveloping worm gearing : the equations including the first enveloping equation, the second enveloping equation, contact line equations of the first enveloping and the second enveloping, boundary equations of the first enveloping and the second enveloping, the equations of relative velocity and absolute velocity
本文介紹了平面二次包絡環面蝸桿傳動的嚙合原理基礎：第一次包絡嚙合方程和第二次包絡嚙合方程，相對速度、相對角速度方程，第一次包絡的接觸線方程，第二次包絡的接觸線方程，以及第一次、第二次包絡的一界線方程和二界線方程。分享友人