嚙合深度 的英文怎麼說

中文拼音 [niègěshēndù]
嚙合深度 英文
depth of engagement
  • 嚙 : 動詞[書面語]1. （鼠、兔等用牙啃或咬） gnaw （at） 2. （侵蝕） erode
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 深 : Ⅰ形容詞1 （從上到下或從外到里的距離大） deep 2 （深奧） difficult; profound 3 （深刻; 深入） thor...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 深度 : 1. （深淺程度） degree of depth; depth 2. （觸及事物本質的程度） profundity; depth
  1. The paper studies the surface geometry of globoidal indexing cam by applying the theory of conjugate surfaces and the method of coordinate transformation, presents the equations related to the main inducement curvature of the cam profiles, analysis and deduces the equations of two circumscription curves, which judge if the conjugate surface could mesh properly. some calculate examples and conclusion are given. the surface equation of the globoidal cam and conjugate equation are established

    論文首先在分析空間嚙合原理基礎上，採用坐標變換法推導出弧面分度凸輪的工作廓面方程、嚙合方程和壓力角計算公式，對弧面分度凸輪的嚙合特性進行了深入的分析和研究，對判斷曲面能否正確嚙合的依據如兩類界限線方程以及誘導主曲率等進行推導，並給出算例。
  2. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  3. 2 ) the spiral bevel gears design method based on the transmission error is proposed. the thesis analyzes deeply the inner relations of between the transmission error and the meshing behaviors, and the valuable information that the transmission error reflects, and investigates further influences of the manufacturing and installing errors, the various loads on the contact behavior of the spiral bevel gears with the high contact ratio. after that, the approach is presented, which assure that the spiral bevel gears have the high real contact ratio and the lower sensitivity to error

    2 ）提出了基於傳動誤差的弧齒錐齒輪設計方法，深入分析了傳動誤差與齒輪嚙合性能的內在關系及其反映的豐富的信息，並進一步研究了各類加工、安裝誤差和載荷變化對高重合度弧齒錐齒輪嚙合性能的影響，提出了對于高重合度弧齒錐齒輪降低誤差敏感性、保證實際重合度的設計途徑和方法。
分享友人
分享到 Line

分享到臉書