均勻流出 的英文怎麼說

中文拼音 [jūnyúnliúchū]
均勻流出 英文
smooth outflow
  • 均 : Ⅰ形容詞（均勻） equal; even Ⅱ副詞（都; 全） without exception; all
  • 勻 : Ⅰ形容詞（均勻） even Ⅱ動詞1. （使均勻） even up; divide evenly 2. （分出一部分） spare
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 流出 : outflow; effusion; runout; vegetate; runoff; profluvium; discharge
  1. The structure of air - blast pipe was improved on. an orienting object was installed based on theoretical analysis, that increase the spraying span. it has been found that both spraying span and droplets uniformity improved, by installing the orienting object. according to the results of a great number of experiments, orderliness of droplets diameter along the spraying span was researched, and rational spraying span of air - assisted sprayer was suggested

    通過試驗檢驗噴霧機樣機的噴霧性能，並提出對各項參數的優化設計方案。通過正交試驗和對比試驗對霧滴取樣，證明導流器的安裝不僅增加了噴幅，而且還提高了霧滴均勻性系數。根據大量試驗的結果分析，找出了霧滴直徑在噴幅方向上所呈現的變化規律，並提出了合理的噴幅范圍。
  2. Brings forward the basic network cell model of symmetrical blast vault and asymmetric blast vault. then studies and analyses airflow in vault of main voltage switchyard hall of xiluodu hydropower station which is far cry and large numbers of airflow conflux, brings forward concept of “ virtual embranchment ” and corresponding basic network cell model, regresses calculate expressions of flux uniformity coefficient and impedance of “ virtual embranchment ” of vault of main voltage switchyard hall of xiluodu hydropower station

    而後又採用cfd數值模擬的方法對溪洛渡水電站主變洞排風拱頂這種多股氣流匯流的長距離通道內的氣流流動進行了分析，提出了「虛擬分支」的概念和相應的網路基元模型，並回歸得到了溪洛渡水電站主變洞排風拱頂各個排風「虛擬分支」風量均勻系數以及阻抗的計算公式。
  3. Based on studying of the unequal rainfall in space - time and the asymmetry physical geography parameters in space, which can influence the process of the runoff, this paper puts forward a sort of slope conflux and watercourse conflux simulating model based on grid, and that gains flux at random time and grid in basin

    本模型針對降雨時空分佈不均勻與下墊面自然地理參數空間分佈不均勻，對產匯流形成過程的影響，提出了一種基於柵格的坡面產匯流與河道匯流的數值模擬模型。
  4. Sylock fan fit for partial cooling and crosscurrent fan blowing equally wide wind

    有適合局部冷卻用的西洛克風扇及送出寬度均勻風力的橫流風扇。
  5. Firstly, simulate flow field of rear smoke channel, plot velocity magnitude and ash concentration distribution in section of entry of heat pipe air preheater, compare with data which were measured in guiyang power station, verify simulation to be reasonable and right. secondly, simulate all kinds of factors which affect flow field ' s uniformity such as length, thickness, location of diffluent board, ash concentration, ash diameter, and so on, find the chiefly factors. thirdly, install guide board in curve channel in rear smoke channel, then simulate its " flow field, plot velocity magnitude and ash concentration distribution

    在此基礎上模擬在冬夏兩季不同情況下，不同流速對熱管空氣預熱器壁面溫度的影響；然後對影響整個流場分佈的各種因素：包括分流板長度、厚度、偏離中心流道位置的偏離度、飛灰濃度、飛灰粒徑等因素進行數值模擬；最後提出在分流煙道轉彎處加裝導流板，並模擬加裝導流板后的流場分佈，得到下級空氣預熱器出口、熱管空氣預熱器進口處的斷面速度場分佈、濃度場分佈，以論證加裝導流板能達到流場均勻化的作用。
  6. In recent years, plentiful and substantial fruits achieved by the lb method in simulations of hydraulics, multiphase flows, flows in porous media and heat transfer as well as magnetohydrodynamics, have revealed a broad perspective of application of this method, it will become a powerful competitor to the conventional approaches. in order to absorb the recent achievement in theory and application of the lb method, explore new ways in hydraulic computation to promote the development of practice, some work is car ried out in this thesis, as following : advances in the theory research and application, deductive process of the d2q9 model and some other commonly used models of the lb method are summarized. based on the hydrodynamic and general boundary conditions, a new joint boundary condition is presented, it integrates advantage of the two conditions above and obtains very good results in dealing with all kinds of boundaries of flow fields

    為了消化和吸收近年來lb方法在理論和應用方面的新成果，探索在水力計算方面的新途徑以促進lb方法實用化的發展，本文進行了下列研究工作：綜述了lb方法在理論研究和實際應用方面的新進展，以及d2q9模型的推導過程和其他一些常用的模型；在水動力邊界條件和通用邊界條件的基礎上提出了一種新的聯合邊界條件方法，它綜合了上述兩種邊界條件的優點，在流場的各種邊界處理中取得了非常好的效果，經過模塊化的處理以後這種邊界條件具有更好的實用性；針對均勻網格的lb方法計算效率較低的不足，提出了雙重網格的latticeboltzmann方法，通過二維poiseulle流動、后臺階流動和渠道方槽流動三個算例的模擬，證明這種方法能夠明顯地提高流場模擬的計算效率；此外，根據復雜區域流場的特徵提出了latticeboltzmann方法的分塊-耦合演算法，利用lb方法的計算特性實現塊與塊之間的數據交換，充分利用計算資源提高計算效率，通過對「 t 」型、 「十」型和「 x 」型分岔管道流場的模擬，展示了這種演算法的特徵和優點，以及它所具有的應用前景。
  7. The axial magnetic field distribution on center surface of contact gap and contact piece are calculated when the current is at peak. it can be found that the intensity of axial magnetic field and radial magnetic field uniformity are strengthened after the iron core is put into, this helps to improve the stability of the vacuum arc

    計算了電流峰值時觸頭間隙中心平面和觸頭片上的縱向磁場分佈，可以看出加入鐵芯后縱向磁場強度和徑向磁場均勻性增強，這有利於提高真空電弧的穩定性。
  8. Abstract : based on thestatic wind force factors of a tower and on the root - mean - square of the buffetingdisplacement responses of the tower top, which are measured by wind tunnel tests inlaminar and turbulent field respectively, the static and buffeting internal forces of thetower bottom control sections under its design wind speed are obtained by linearsuperposition method and fem

    文摘:基於均勻流和紊流風場中的橋塔模型風洞試驗所測得的橋塔空氣力靜力系數及塔頂抖振響應的位移均方根，採用線性疊加法及有限元法反演，給出設計風速下塔底控制截面的順風向靜風及抖振內力。
  9. ( 4 ) through the hydraulic property experiment of micro - hole lateral pipes of simple sdi in air, it was found that the average pressure of 60 mitre length lateral pipes was at the position of per 40o / o ~ ~ ~ 50 % of the effectual pipe length from the fist micro - hole, major pressure - loss was occurred at the ahead part of half pipe. the pressure uniformity reduced with orifice aperture ? increasing, and the relationship between pressure uniformity and initial water pressure was poor. running under the initial water pressure of 1. 5 meter, the discharge uniformity reduced with orifice aperture ? increasing, and when the orifice aperture smaller than or equal 1. 0mm, irrigation uniformity could achieve above 0. 6

    （ 3 ）通過對空氣介質中簡易地下滴灌的微孔毛管試驗研究發現： 60m管長的毛管平均壓力水頭的位置基本上在距第一孔口的有效管長40 - 45的地方；大部分水頭損失發生在毛管的前半部分；壓力均勻度隨孔徑的增大而減小，但與初始工作水頭關系不密切；在1 . 5m以下的工作壓力下運行，沿程出流均勻度隨孔徑的增大而降低，當孔徑不大於1 . 0mm時，灌水均勻度可以達到60以上；當孔徑大於等於1 . 2mm時，灌水均勻度低於50 。
  10. And the results of calculation and numerical simulation indicate, without increasing the intrinsic collector - junction area of power devices, collector - combed structure helps to raise the intrinsic heat - dissipating area and base ' s perimeter, improve heat - dissipating method of each cell of the chip, enhance the distribution uniformity of junction temperature and current of each cell of the chip, reduce the thermal resistance and raise the dissipation power pd and output power p0, fairly well relax the contradiction among frequency, out - put power and dissipation power of the devices, and further improve the devices " property against second breakdown

    而計算分析和二維數值模擬分析結果表明：梳狀集電結（基區）結構在不增加器件本徵集電結面積的條件下，增大了器件的本徵散熱面積和基區周長，改進了每個子器件單元內的散熱方式，提高了單元內結溫和電流分佈的均勻性，降低了器件的熱阻，增大了器件的耗散功率和輸出功率，較好地緩解了目前傳統結構中頻率與功率、功耗的矛盾，並有利於改善器件抗二次擊穿的性能。
  11. Based on the green ' s formula and the assumption of the propeller blade ' s thin sections, a lifting - surface method of propellers with the vortex lattice and equal source panel distributions on the mean camber surface has been introduced for the prediction of steady propeller ' s hydrodynamics in this paper. an approximate kurta condition was applied

    基於creen公式和薄翼理論假設導出的升力面方法，採用在螺旋槳拱弧面上分佈離散渦、源布置方法預報均勻流場中的螺旋槳的定常性能，螺旋槳尾渦面上壓力連續性條件採用近似的kutta條件處理。
  12. The air absorbed by the fans is separated in and equably flows in the interior and outer canister, from to the heater and interior canister, the air is efficiently heat - treated, then the hot air influxes to and is balanced in because of the mixing by the heater, the hot airs temperature in has only little change, then it is separated completely from to ensure the balance - dryness of the colophony

    由鼓風機吸入的空氣在處被分散，于內筒和外筒間均勻地流動，從處進入內筒和加熱管進行有效地熱交換。然後熱風在處匯集，在處無序混亂的熱內被均化。由於加熱箱熱風混合效果的作風，處的熱風溫度變化幅度很小，熱風經熱風排出口被完全均勻地分散開，從而保證了樹脂均勻乾燥。
  13. Installation requires no water draining. simply lower the pipes at tank side and let it sink to the bottom to send up air for aeration. for maintenance, pull up pipe to remove surface deposits, then return it to bottom again

    個細孔出氣，上升帶動全池污水繞流均勻，施工免抽水，由池上放入污水池邊，使其沉下池底送風曝氣即可，保養時上拉清除表皮再放回即完成。
  14. The numerical simulations show that the phase plane and amplitude plane in orthotropic fluid - saturated porous media is not paralleled to each other any more though the dispersion caused by the fluid is omitted. it is one kind of non - homogeneous wave. the maximum attenuation is no longer

    指出由於介質的各向異性，盡管忽略了流體粘度引起的粘度耗散，正交各向異性液飽和多孔介質中瑞利波的相平面和幅平面亦不再重合，為非均勻波，最大的衰減不再沿波傳播方向。
  15. This paper presents a design method of propeller blade section operating in non - uniform flow field and an idea of equivalent operating curve with unchanged cavitations characteristic on blade section, the method for selecting the curve is set up

    摘要給出了非均勻流場中螺旋槳槳葉剖面的設計方法，提出了保持剖面空泡特徵不變的等效運轉曲線的思想，並創建了等效運轉曲線的確定方法。
  16. Part ii : a third possible mechanism for the effect of nonuniform current on short waves is suggested, which ascribes the modulation of short wave spectrum by current to that the current changes the drift, through which it changes the breaking criteria, as a result the energy dissipation is altered

    第二部分:本文提出非均勻流場影響短波譜的第三個可能機制:非均勻流場通過對表面漂流的調制，改變風浪破碎的閉值條件，進而改變破碎損耗，從而調制海面小尺度粗糙度。
  17. When the propeller operates in the spatially non - uniform velocity field behind the ship, the unsteady cavitation on the blades often causes the vibration of ship structure, the propeller noise and the cavitation erosion on the blade

    在船尾非均勻流場中工作的螺旋槳，常常由於槳葉上產生了非定常空泡，導致船尾振動和螺旋槳噪聲，致使槳葉表面出現空泡剝蝕。
  18. The materials - air circulation is existed in the ginding chamber of hammer mill when grinding materials. it led to lower production, higher consumption of energy and particle inhomogeity. aiming at materials - air circulation, the special type grinding chamber that is made up of trapezium screen was proposed

    針對錘片式粉碎機工作時粉碎室內存在物料-空氣環流層，導致其粉碎效率低、能耗高，且粉碎物粒度不均勻，提出使用梯形篩片構成的異型粉碎室來改善錘片式粉碎機的性能。
  19. In order to know the relationship between gas - content and pipeline ' s pressure drop, the thesis deduces the pressure drop calculating equations based on uniform flow pattern and separating flow pattern. the equations show that pressure drop is made up of three parts, that is, friction resistance effect, gas acceleration effect and the gravity effect. and the research has shown that the gas has little effect on pressure drop. in the horizontal pipeline, the resistance effect must be overmatched the acceleration effect

    為探討加入的氣體對管道壓力的影響，本文基於分相流和均相流兩種模型分別推導了三相流管道的壓降公式，表明無論是分相流模型，還是均勻流模型，管道內流體總的壓降是由三項組成的，即摩擦項、加速項和重力項，並得出了加氣對管壓變化不大的結論，所以認為在水平管道中，要獲得有效的減阻，則要使摩擦阻力分量的減小效應大於漿體加氣的加速效應。
  20. Especially the paper relatively systemically cleans up and deduces a mathematical model of the ship maneuvering simulation that is fit for the ship maneuvering simulator for the demonstration of the designs of harbor and fairway, which makes a strong foundation for the manufacture of our country " s ship maneuvering simulator for the demonstration of the designs of harbor and fairway. then author designs a sort of twain dimensions ship maneuvering simulator for the demonstration of the designs of harbor and fairway that is based on pc and is fit for the developing country, which provides a piece of trail of the thought for the development of our country " s new generation ship simulator

    探討了運用於港航設計論證的模擬器中不均勻流場數據的處理方法；比較系統的整理、推導出一套適合於港航設計論證的船舶操縱模擬器的船舶操縱運動數學模型，為我國基於港航設計論證的船舶操縱模擬器的進一步研製工作打下了堅實的基礎；在此基礎上設計了一種基於pc機的，適合於發展中國家的，運用於港航設計論證的二維船舶操縱模擬器的框架，希望能為我國新一代運用於港航設計論證的模擬器的研製提供一條思路。
分享友人
分享到 Line

分享到臉書