均勻粘性流 的英文怎麼說

中文拼音 [jūnyúnniánxìngliú]
均勻粘性流 英文
uniform viscous flow
  • 均 : Ⅰ形容詞（均勻） equal; even Ⅱ副詞（都; 全） without exception; all
  • 勻 : Ⅰ形容詞（均勻） even Ⅱ動詞1. （使均勻） even up; divide evenly 2. （分出一部分） spare
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  1. The numerical simulations show that the phase plane and amplitude plane in orthotropic fluid - saturated porous media is not paralleled to each other any more though the dispersion caused by the fluid is omitted. it is one kind of non - homogeneous wave. the maximum attenuation is no longer

    指出由於介質的各向異性，盡管忽略了流體粘度引起的粘度耗散，正交各向異性液飽和多孔介質中瑞利波的相平面和幅平面亦不再重合，為非均勻波，最大的衰減不再沿波傳播方向。
  2. On the contrary if resin ' s viscosity is very low, the capacity of resin in soiled thing become lower. both this two conditions can lead to decrease product ' s performance. in the manufacturing of fiber reinforced plastic production, measurement and control of resin viscosity is always a difficult problem to resolve

    樹脂的粘度越高，那麼其流動性越差，原材料外表面上的樹脂分佈就越不均勻；反之，如果樹脂的粘度很低，被浸漬物的浸膠量會過低，這兩種情況都將導致製品性能下降。
  3. 2. effect of the viscosity ratio, mterfacial adhesion, processing conditions and composition on the dispersing morphology and properties of pp / eoc blends was investigated. low viscosity ratio and high shear rate during processing were found to produce fine and uniform dispersion of eoc in pp matrix, while low viscosity ratio, high interfacial interaction, good fluidity of elastomer and high shear rate in molding process resulted in fibril dispersion, which afford a guide for controlling the morphology of pp / eoc blends

    研究了粘度比、界面相互作用、加工條件和共混比例等因素對pp eoc體系分散形態和性能的影響，發現粘度比小和加工過程中剪切強度大有利於彈性體在基體中分散均勻細化；粘度比小、界面相互作用強、彈性體本身的流動性好及成型時受到的剪切應力大，使彈性體相易變形，沿流動方向取向呈纖，闡明了各因素對形態影響的作用機制，這對pp eoc共混物的形態控制具有重要的指導作用。
  4. We also found that the rheological behavior of single layer gmt is isotropic. temperature and pressure method has great affection on the distribution of the fiber. second, we measure the pressure change under different molding rate and use extensional viscosities model and shear force model to analysis the data

    研究表明： gmt材料具有很好的充模流動性，流動過程中纖維氈保持一個整體； gmt材料擠壓流動行為表現為各向同性；溫度、壓力制度對纖維的均勻分佈影響很大： 2 ）通過測量不同合模速率下壓力變化，採用拉伸粘度模型（ extensionalviscositiesmodel ）和純剪切流動模型（ shearforcemodel ）對數據進行分析，導出了描述gmt材料宏觀行為的流變學參數。
  5. The resulting semi - solid mixture then flows homogeneously, figure 1, behaving as a thixotropic fluid with viscosity depending on fraction solid, morphology, shear rate and time

    這樣最終形成的半固態混合物會均勻地流動（圖表1 ） ，並依據固體粒度、晶形、剪切速率及時間而形成粘性觸變液體。
分享友人
分享到 Line

分享到臉書