坡口 的英文怎麼說

中文拼音 [pōkǒu]
坡口 英文
beveled edges
  • 坡 : Ⅰ名詞（地面傾斜的地方） slope Ⅱ形容詞（傾斜） sloping; slanting
  • 口 : Ⅰ名詞1 （人或動物進飲食的器官; 嘴） mouth 2 （容器通外面的地方） mouth; rim 3 （出入通過的地方） ...
  1. Coil spring loaded slotted oil control ring

    螺旋彈簧加載雙坡口油環
  2. As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers

    本機床是電站大型汽輪發電機組的管道施工的關鍵設備，對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口，端平面，內外徑過緩斜度及直口，能滿足施工現場和製造廠家對各種管件的加工要求。
  3. Cracks have been found in the flange and web splices at groove welds in at least four bridges.

    至少在四座橋梁的翼緣板和腹板拼接坡口焊縫中發現了裂紋。
  4. These attachments were considered secondary components, so no weld quality control has been imposed on the groove weld splice.

    這些附連件被看作是次要的部件，所以在這種坡口焊接中沒有進行焊接質量控制。
  5. Add metal from the rod by dipping the end into the pool so that it melts and makes up the vee.

    將焊條一端浸入池內熔化，填滿V形坡口。
  6. This paper describes the difference between the terms of groove and bevel in weld joints and condition in asme code translation

    本文敘述焊接接頭中術語剖口與坡口的區別和在asme規范翻譯中應注意的問題。
  7. This product is a ideal machine to cut the seal of processing vessel and its linear velocity is nonstage transmission. its edge face and groove can be finished in one time and it is several times more effective than before

    本機是加工容器封頭切割的最佳設備，線速度無級調速，端面和坡口可一次加工完成，比立車加工功效提高幾倍。
  8. 5 all single - sided groove joints in nickel alloys, stainless steel and ferritic alloys containing more than two ( 2 ) percent chromium shall be welded using a gas tungsten - arc root pass with an inert gas back purge

    鉻含量超過2 %的鎳合金、不銹鋼和鐵素體合金的單面坡口焊道用鎢極氣體保護焊，其根部焊道用惰性氣體反吹。
  9. Often lack of fusion adjacent to the girder web in the transverse groove welds led to the cracking.

    在靠近主梁腹板的橫向坡口焊縫處常常出現未熔透而導致裂紋。
  10. Specializing in the production of jack, hydraulic wrench, hydraulic nuts, bolts hydraulic tensile, snorkel platform groove machine, demolition broken clamp, the manual hydraulic pump, electric and pneumatic hydraulic pumps and other hydraulic pump

    專業生產千斤頂、液壓扳手、液壓螺母、螺栓拉伸器、液壓升降平臺、坡口機、拆破鉗、手動液壓泵、電動液壓泵和氣動液壓泵等。
  11. This chamfering machine employs the principle of rolling shear to shear the edge of the steel plate according to the angel needed, to obtain the bevel for w - elding

    該倒角機利用滾剪原理，對鋼板邊緣按所需角度進行剪切，以得到焊接所需坡口。
  12. For all processes, the welding procedure specification ( wps ) shall contain a detailed cleaning procedure indicating joint preparation prior to welding

    對于所有焊接方法，焊接工藝規程都應詳細包含清除方法，說明焊前坡口的準備。
  13. This consists for the most part in straightening up, cleaning, and, on thicker plates above 5/16 in vee-ing the edges.

    主要是矯直，清選，對于厚度超過516英寸的金屬板，還需將焊邊做成V形坡口。
  14. The second crack is a crack originating at the groove weld toe of the column flange-girder flange connection.

    第二種是產生於立柱翼緣與主梁翼緣連接處的坡口焊縫焊趾處的裂紋。
  15. Two pfms are normally used on major pipeline projects

    大多數管道工程通常使用兩個坡口機。
  16. Range of use : cz2. 5 air shovel is used for clearing slag by electric welding, beveling groove. it also can do some shovelling and cutting on steel cast

    使用范圍： cz2 . 5型氣才鏟適用於電焊去渣、去毛邊、去坡口，也可在鋼結物體、鑄件上進行少量鏟削。
  17. A large number of these cracks occurred because the groove welded component was considered a secondary member or attachment.

    發生這許多裂紋是因為把這些坡口焊接部件作為次要構件或附件考慮。
  18. A saddle - shaped hole grooving machine for pressure vessel was introduced. a method for processing saddle groove and the designing of a technical background were put forward

    摘要介紹了一種壓力容器殼體開孔馬鞍形坡口加工機械的設計背景技術，給出了馬鞍形坡口加工的一種實現方法。
  19. It is then ready for the operator to initiate faceplate rotation and machine the bevel

    此時操作者可啟動旋轉面板並切削坡口。
  20. Strictly checking the clamping device of beveling machine to be free from loosen

    使用前應嚴格檢查坡口機夾緊裝置是否有松動現象。
分享友人
分享到 Line

分享到臉書