彎緣機 的英文怎麼說
中文拼音 [wānyuánjī]
彎緣機
英文
flanger-
The test proves that the caudal fin oscillation frequency, the maximum amplitude of vibration of caudal fin, the caudal fin strikes the water angle influence the fish ’ s speed ; the curve experiment has obtained curve radius of inertia advance curve and static curve ; the ups and downs experiment proves that the pectoral fin on different angle influences the fish to move ups and downs
加減速試驗論證了尾鰭擺動頻率、尾鰭后緣最大擺幅以及尾鰭的最大擊水角度對魚體速度的影響;轉彎試驗測得了機器魚慣性前進轉彎和靜止轉彎時的轉彎半徑;在機器魚的升潛試驗中論證了胸鰭不同轉角對升潛運動的影響。Energy consume, electric strength, insulation resistance, ground conductivity, leakage current, microwave leakage, power input, normal temperature, humidity treatment, glow wire, horizontal flame, vertical flame, tracking, ball pressure, rainproof, water splash, dustproof, salt fog, endurance, motor load test, cord flexing, cord pulling, pull & torque test, lamp replacement, construction check etc
能耗、電氣強度、絕緣電阻、接地連續性、泄漏電流、微波泄漏、功率、溫升、濕熱試驗、灼熱絲、水平燃燒、垂直燃燒、漏電起痕、球壓試驗、防雨淋、防濺水、粉塵、鹽霧、耐久性(壽命)試驗、電機負載試驗、電源線彎折、電源線提拉、拉扭力測試、燈頭互換性、安全結構檢查等。Stretch - bending former is used to manufacture curved pieces with large size and high shaped precision. generally, these pieces are relatively large winding radius extrusion or sheet bending profiled bars. especially, stretch - bending former is the needed equipment to produce rims, ribs, edges and strips of airplanes
拉彎機是生產加工飛機上的框肋緣條等型材零件的必須設備,常用於製造尺寸大、外形準確度要求較高、相對彎曲半徑大的擠壓和板彎型材彎曲件。Flipping among imagery, topographic maps and reconnaissance scans, the editors tweaked the route to take tight turns the way a race driver would and to shy away from cliff edges
路線編輯員必須快速瀏覽影像、地形圖及勘察掃描結果,精確調整路線,讓機器人像賽車選手那樣精準過彎,並且避開懸崖邊緣。A certain number ( odd number ) of enameled flat wires, through precise action of a transposition unit, are edgewise bent, repeatedly crosswise transposed, and braided into a bundle conductor, and then the bundle conductor is wrapped with paper as its insulation so as to become a finished product
設備的主要功能是通過換位裝置準確的機械動作將一定根數(奇數)的漆包扁線進行小邊彎曲,迭次交叉換位,編結成集束導線,然後包紙絕緣成為產品。The effects of leading edge skewed - swept blade on meridian acceleration fan
前緣彎掠影響子午加速風機內流的研究In allusion to the characters of structuralized road and images acquired through projection, we divide the lane into three parts according to golden section and extract each section ' s edge
針對結構化道路的特點,以及經攝像機投影的道路彎曲的圖像特徵,提出了將道路按黃金分割0 . 618分為由近至遠的三段,對每段進行分段線性化提取道路邊緣。2 based on experimental results and finite elements analysis of new joint, the stress transfer mechanism of the new joint is analyzed. there are two stress transfer patterns about the new joint, one is for rectangular steel tubular column joint, its stress transfer pattern is that beam moment is transferred to column webs mainly by stiffeners, the other is for crft column joint, its stress transfer pattern is that part of beam moment is transferred from stiffeners to column webs, another part of beam moment is transferred to infilled concrete by column flange
(二)基於新型節點的試驗結果和有限元分析,研究了新型節點的傳力機理,其應力的傳遞路徑分為兩種:對于鋼管柱節點,梁端彎矩主要通過加勁肋板直接傳至柱腹板,對于鋼管混凝土柱節點,梁端彎矩一部分通過加勁肋傳給柱腹板,另一部分通過柱翼緣傳給鋼管內的混凝土。The pvc insulated nylon sheathed wire has advantages with excellent thermal stability, larger machanical strength and surface strength, anti - thermal - distortion, better bending strength and impulse strength, abrasion resistance and chemical - resistance and self - lubrication as well as better machine - oil - resistance and gas - proof
尼龍護套pvc絕緣電線具有優良的熱穩定性、較高的機械強度、表面強度、耐熱變形性、抗彎強度、沖擊強度、耐磨性、耐耐化學性和自潤滑性, 2 、更具有耐機油、耐汽油性。Stiff struts and ribs meant that wings were too rigid to flex much torsionally, so builders installed ailerons ? flaps located on the outer, trailing - edge portions of wings
難以彎曲的支柱和翼肋,使得機翼太過剛硬,同時也限制了扭轉幅度,因此工程師加上了副翼,也就是位於機翼后緣外側的襟翼。Test method for formability of attached organic coatings with impact - wedge bend apparatus
用沖擊邊緣彎曲儀測定附加有機塗層可成形性的試驗方法分享友人