恆壓響應 的英文怎麼說
中文拼音 [héngyāxiǎngyīng]
恆壓響應
英文
constant-voltage response-
The effects of the fabrication conditions on the crystal structure, grain size, micromorphology and electrochemical performance of these materials have been studied in depth. the reaction mechanism of the low - heating solid - state reaction method has also been investigated. in addition, a novel electrochemical method ( rpg method ) based on the concept of " ratio of potentio - galvano - charge capacity " has been for the first time developed to determine the diffusion coefficient of lithium - ion within insertion - host materials on the basis of the spherical diffusion model
本論文較系統地考察了低熱固相反應法合成鋰離子電池正極材料的可行性問題，研究了工藝條件對材料的晶體結構、晶粒尺寸、微觀形貌及電化學性能等的影響，探討了低熱固相反應的機理，並通過引進「恆壓-恆流充電容量比」的概念，給出了一種測定鋰離子嵌入脫出固相擴散系數的新方法。The result of the study shows that the electro - hydraulic proportional technology is useful for all - hydraulic operated drilling machine to simplify the operations and composition of system, to improve the level of automatization and efficiency and to reduce the consumption of energy. the result of the study also shows that the system of feeding has the properties as followed : fast respone, stable pressure - adjusted characteristic, distinct effect of energy - saving, some improvement of system efficiency
研究結果表明：全液壓鉆機中應用電液比例技術，可以簡化系統組成和操作，提高鉆機自動化水平，提高系統效率，降低發熱和溫升；採用恆壓變量泵的給進加壓電液比例控制系統調壓性能穩定、響應快、節能效果明顯。When the transportation load is long - term evenly distributed, the influences of each relevant factor, i. e. pipeline depth, diameter, deformation module of foundation, poisson ratio of soil and tyre pressure of vehicles, toward mises stress and vertical displacement of pipelines are discussed. when the transportation load is movable and invariable, the changing rules of mises stress and vertical displacement during the vehicle ' s movement are calculated and analyzed, and effects of vehicle velocity and tyre pressure toward these two mechanical characteristics are discussed. when the transportation load is stable and simple harmonic, the changing rules of mises stress and vertical displacement during the time of load function are calculated and analyzed, and effects of vehicle velocity and tyre pressure toward these two mechanical characteristics are also discussed. in three - dimensional analysis, mises stress and vertical displacement of pipelines under three kinds of transportation loads are calculated, and the analysis and discussion of correlative factors are also made
當交通荷載為長期均布荷載時，討論了各相關因素，包括管道埋深、管徑、地基變形模量、地基泊松比和車輛輪壓大小分別對管道mises應力和豎向位移的影響；當交通荷載為移動恆載時，計算並分析了車輛行駛過程中管道mises應力和豎向位移的變化規律，討論了車速和車輛輪壓對這兩個管道力學性狀的影響；當交通荷載為穩態簡諧荷載時，計算並分析了荷載作用時間內管道mises應力和豎向位移的變化規律，討論了車速和車輛輪壓對管道力學性狀的影響。In this dissertation, the experimental study of rolling condition on two - phase flow instabilities of the forced - single - tube circulation system was carried out. furthermore, based on the d - partition method and the hypothesis of drift flow model, given some conservative equation, using the perturbation method the response of the pressure drop of the tube to the inlet flow rate perturbation was analyzed both in rolling condition and in normal upright position
本文主要通過實驗對搖擺條件對單管強迫循環中汽液兩相流動不穩定性的影響，同時在d分區法的前提下，在兩相區基於漂移流模型，一定的守恆條件下，在搖擺和不搖擺工況中用線性小擾動法對實驗段的壓降對入口流速的擾動的響應進行了分析。Abstract : in this paper, rigid visco - plastic fem technique is applied to numerically analyze the factors affecting the forming time of superplastic bulging, and the regularities of forming time affected by different factors are given by examples of constant pressure and constant strain rate die - bulging of cylinder parts, all of which provides guideline for process planning in actual superplastic bulging
文摘:採用剛粘塑性有限元技術對超塑性脹形成形時間的影響因素進行了數值分析，以圓筒形零件的恆壓和恆應變速率充模脹形為例，給出了不同因素對超塑性成形時間的影響規律，為超塑性脹形實際工藝設計提供了依據。After debugging the waveform control system and man - machine interface system, we program constant - current control software and research respectively the current and voltage step response of power source. at last, the carbon dioxide welding method is realized in the welding machine controlled by the waveform control program. the simulated load test is also made here
本文在完成所設計的波形控制系統和人機介面交互系統的調試后，首先編寫軟體實現了電源的恆流控制，並研究了該電源的電流、電壓的動態響應性能，最後，編寫控制軟體實現了雙斜率波形控制co2焊的功能並進行了模擬短路過渡負載試驗。The system simultaneously used the technique of computer, electron as well as single - chip microcomputer, and solved the key problem brought about by the pump ' s high speed revolving all the time. that is, the electrical energy ' s waste, which existed in the water supply system of the city and the high building. at the same time overcome the shortcomimg of long reaction time of the traditional water supply system, varied frequency at low speed, made use of large area, and consume a lot
該系統集計算機、電子技術於一體，不但解決了目前城市供水系統和小區高樓供水中，水泵一直高速轉動所帶來的電能浪費的問題，而且也克服了傳統的供水系統響應時間長，變頻速度慢，佔地面積大，投資大等缺點，為實時恆壓供水提供了一種實用的方法。The director of liquid crystal will generate an evident transformation due to the flexoelectric effect induced by an external invariant voltage normal to the plane of the glass plates
沿垂直於玻璃基板表面的方向加一恆定的電壓，由於撓曲電效應的影響，液晶指向矢將會發生明顯的變化。分享友人