扭法螺 的英文怎麼說
中文拼音 [niǔfǎluó]
扭法螺
英文
murex anus-
Crenshaw deciphered the algorithm of the twisting motion, known as helical klinotaxis, and assisted nekton ' s team in applying it to the robots, in essence crafting a new guidance technology
克倫肖解算出螺旋狀調轉趨性這種扭擺運動的運作法則，並協助耐頓研究所的團隊設計機器人，基本上是要發展出一種全新的導向技術。In the work, it is founded to study the thermal degradation of the polymer by study the change of toque of micro twin screw extruder
在本論文工作中，建立了通過微型雙螺桿扭矩變化來研究聚合物的熱降解情況的方法。For reducing the disadvantageous influence of the the relaxation of strain and the lose of pretension on the structure, the time span of delaying scene torsional moment checx and accurate maintence method are given
為減少高強螺栓預拉應變鬆弛和預拉應力損失對結構的不利影響，給出了延遲現場扭矩檢測的時間區間和正確維護的方法。After proper operation has been verified, tighten all bolts using the crossover method. recommended tightening torques pattern is listed below
在檢驗操作能夠正常進行后，在採用交叉法緊固所有螺栓。推薦的緊固扭矩模式如下所示。The running condition would be deteriorated and at last the parts of the engine would be damaged if the revolution were reduced too low. the propeller must be redesigned or be modified in this situation. people usually modify the propeller rather than change the propeller because it will be more easily and economical
此時若要更換新的螺旋槳必然造成經濟上過重的負擔，較方便可行的方法是對原來的螺旋槳採取切邊修改的方法，減少螺旋槳的直徑、盤面積或螺距，使螺旋槳的扭矩減小，螺槳變「輕」 。Test method for mechanical torque rate of spiral coils of thermostat metal
恆溫雙金屬制螺旋線圈的機械扭轉率的試驗方法Assembly tools for screws and nuts - hand torque tools - requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure
螺釘和螺母用裝配工具.手動扭具.設計合格檢驗質量合格檢驗和再校準程序的要求和試驗方法The method of torque - angle is adopted as the control method of the intelligent screw tightening machine on the basis of analyzing the excellence and deficiency of all kinds of control methods and taking practical situation into account. secondly, the design of the machinery of the tightening machine is explained in detail, almost all parts of the structure principle diagrams are given and an introduction of function of each part in the diagram is made concisely
文章首先對螺紋擰緊的控制方法進行了探討，在分析各種方法優缺點和結合實際情況的基礎上採用扭矩轉角法為螺紋自動擰緊機的控制方法。然後，文章詳細地介紹了擰緊機的機構部分設計，給出了擰緊機的各部分的結構原理圖，並對原理圖中的各個環節的功能作了簡要介紹。The surface panel method has been applied to predict the hydrodynamic performance of highly skewed propeller. the surface of propeller and its trailing vortex are discreted by a number of small hyperboloidal quadrilateral panels with constant source and doublet distribution. for highly skewed propeller, the conventional method generating grid oriented along constant radii will result in a high aspect ratio and a high skewness and a twist panel near the propeller tip on blade surface, which result easily in incorrect calculation results of velovity on blade surface, even in iteration divergence and calculation failure. a “ non - conventional grid ” is developed to acoid these problems. this grid can effectively solve the problem of the calculation and convergence for highly skewed propeller. the non - linear kutta condition of equal pressure on upper and lower at the trailing edge is executed by the iterative procedure. by sample calculating, the obtained results are satisfied the experimental data
採用面元法預報大側斜螺旋槳水動力性能，螺旋槳表面及尾渦面離散為四邊形雙曲面元，每個面元上布置等強度源匯和偶極子分佈.對于大側斜螺旋槳而言，槳葉表面採用常規的等半徑網格劃分方法在近葉梢處將導致大展弦比、大側斜和扭曲面元，這容易使槳葉表面速度的計算結果不正確，甚至會導致迭代過程發散及計算失敗.文中建立了一種「非常規網格」劃分方法，能有效地解決大側斜螺旋槳的計算和收斂問題.槳葉隨邊處通過迭代實現非線性等壓庫塔條件Prevailing torque type all - metal hexagon nuts with flange with metric fine pitch thread
帶公制小螺距螺紋法蘭的流行全金屬扭矩型六角螺母Prevailing - torque type steel metric hex nuts and hex flange nuts
經常作用的扭矩型鋼制米制六角螺母和六角法蘭螺母Helical torsion springs - requirements for design, performance test method
螺旋扭力彈簧.設計要求和性能試驗方法Standard test method for application and removal torque of threaded or lug - style closures
螺紋或突耳型閉塞物的應用及移動扭矩的試驗方法分享友人