拉模孔型 的英文怎麼說
中文拼音 [lāmókǒngxíng]
拉模孔型
英文
die profile-
At the same time we study, analysis and discuss the action that non - linearity - stickiness - springiness and crazing damage of the pmma sample under creep though making us of the knowledge about the high molecule physics the damage theory of material of rheology of bodies with defects. through the study and theory analysis of single - axes stretching experiment in pmma sample under creep, take the surface crazing damage density of pmma sample as an variable, to look for a commonly rule that the crazing damage of pmma, and to offer a feasible damage model for the sake of study that of pmma ' s remoteness damage
同時運用高分子物理、含缺陷流變性物體的材料破壞理論等知識，對無孔洞pmma試件和有孔洞pmma試件蠕變條件下非線性粘彈性行為及其銀紋損傷現象進行了研究、分析與探討，通過對蠕變條件下的pmma試件的單軸拉伸實驗研究和理論分析，以pmma試件的銀紋損傷面密度值為損傷變量，來嘗試尋求pmma銀紋損傷的一般規律，為研究pmma的細觀損傷提供了一種可行的損傷模型。Sem, transmission electron microscopy ( tem ), x - ray energy - dispersion analysis ( edax ), xrd, electron diffraction ( ed ) and high - resolution electron microscopy ( hrem ) were used to investigate the morphology, atomic composition and crystal structure of the nanowires. the hexagonal cdse nanowires with single crystal structure have been obtained in dmso under 140. ( 3 ) semiconductor te and cdte nanowires embedded in aao templates were fabricated for the first time by dc < wp = 7 > electrodeposition in ethylene glycol
Sem 、 tem 、 edax 、 xrd 、 ed 、 hrem分析的結果表明，所得cdse納米線為六方晶型，晶體的（ 001 ）晶面沿平行於基底的方向擇優生長，且隨沉積溫度的降低，這種擇優生長的趨勢越來越強；納米線晶體在生長時，由於受aao模板孔徑的限制，形成c軸方向拉長的晶粒，其長徑比達5 1以上；晶體的大小和完善程度隨沉積溫度的降低而增大， 185沉積得到多晶六方cdse納米線，而140沉積時可得到六方cdse單晶納米線。In consider drilling rod state, hole state, creep into course influence foundation of parameter synthetically, the drilling rod model under acting on the pulling force and torsion together carries on the theory to calculate, receive drilling rod pulling force and torsion differential equation group, in order to benefit drilling rod strength further to analyse
在綜合考慮鉆桿狀況、鉆孔狀況、鉆進過程參數的影響基礎上，對拉力和扭矩共同作用下的鉆桿模型進行理論計算，得到鉆桿拉力一扭矩微分方程組，以利於鉆桿受力的進一步分析。In order to optimize the perpetuation tensioning tonnage of prestressed pier anchor wire of goupitan arch dam, first the scheme contrast method is adopted to define the perpetuation tensioning tonnage combination of the primary and secondary anchor wire, but the optimization result is that the pull - anchor coefficient is too big ; then the body form of the pier is optimized ; finally the anchor wire perpetuation tensioning tonnage is optimized by using ansys optimization design module based on parametric fem, the optimization result is acceptable and the pull - anchor coefficient is lowered down
摘要為優化構皮灘拱壩中孔預應力閘墩錨索永存張拉噸位，首先採用方案優選的方法確定主次錨索永存張拉噸位組合，但優選結果拉錨系數偏大，再對閘墩體型進行優化，然後採用基於參數化有限元的ansys優化設計模塊對主次錨索永存張拉噸位進行優化，優化結果滿足應力控制要求，降低了拉錨系數。Experimental specimens embedded with superelastic wires, which are rectangle laminated composite panels with a circular hole and square plate, were prepared to make respectively tensile and bending test. the outputs of sensors embedded in structures were timely acquired to monitor mechanical properties of structure
對含孔洞的典型構件進行拉伸試驗，對方板構件進行彎曲模擬受載試驗，實時採集結構中傳感元件的輸出，以實驗的方法監測結構宏觀力學行為。分享友人