指令傳送線 的英文怎麼說

中文拼音 [zhǐlìngzhuànsòngxiàn]
指令傳送線 英文
command line
  • 指 : 指構詞成分。
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  • 送 : 動詞1 （運送; 傳送） deliver; carry 2 （贈送） give as a present; give 3 （伴送; 送別） see sb of...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 指令 : 1 （指示; 命令） instruct; order; direct2 （上級機關對下級機關的指示） instructions; order; direc...
  1. It includes : dynamic show of technics flow, real time data acquirement and show, history data save and print, fault alarm, etc. the plc control system mainly accomplishes the wastewater technics flow control, harmonizes the logical relationship among local intelligent control instruments and transmits the state of each local equipment to the industrial computer simultaneously, the plc control station receives the control commands from the industrial computer ; the local intelligent units take charge of the correlated parameters measure, disposal and control, and it will transmit the related parameters to the computer, etc. in this thesis, introduced municipal wastewater treatment technics, the integrated application program development of computer, the design method of plc control station, the communication between plc control system and computer, and the network of wastewater treatment with profibus - dp was also discussed

    上位計算機主要實現遠程監測和管理功能，具體包括:工藝流程動態顯示、實時數據獲得及顯示、歷史數據存儲與列印、故障報警等功能plc控制系統主要完成工藝流程式控制制以及協調現場各智能儀表之間的邏輯關系，將現場各設備的運行狀態通過通訊網路傳輸到上位計算機，並接收上位計算機的控制指令;現場各智能儀表單元負責各相關參數的監測和處理、控制，並將有關參數送往上位監控計算機進行處理、保存等。本文以莎車污水處理項目為例，介紹了城市污水處理工藝、上位監控計算機的綜合應用程序開發、城市污水處理自動控制系統plc控制站的設計和採用profibus系列中廣泛應用於現場設備的profibus - dp總線。
  2. Before the connectting between moden and other equipments, it works at the cammand mode, the cammand that is send to moden is used to set or manipulate the mode, after the connectting between moden and other equipments, it works at connectting mode, at that time, the cammand send from the computer is send to another computer which will pass the moden and telephone line. the moden control cammand is called " at " cammand, all the control manipulation is realized by sending the ascii character to moden, after the moden received the " at " cammand, it firstly judges the cammand, secondly, it analyses and executes the cammand, finnally, it executes a response by sending back a ascii character, during the deseign of below - computer, we introduce in detail the deseign of system hardware and system software, below - computer system hardware and system software, below - computer is made up of microchip collecting and controlling system, which finish the strobe and water level data collection, display and disposal, deal with the communication with the above - computer, the microchip is the centre of data dealing with, the peripheral equipments are made up of data collecttion module, control cammand input module, display module, execute output module, and long - distance communication module

    在moden控制軟體的設計中，詳細敘述了moden正常工作時的幾個重要函數：初始化函數、撥號處理函數、應答處理函數、掛機處理函數，設計並調試了四個函數的通信程序，數據機工作時存在兩種模式，命令模式與連線模式，命令模式是針對功能設置的模式，連線模式是數據傳輸的模式。當數據機未與其他設備連接時，其處于命令模式，這時候下達給數據機的指令是作為數據機本身設置或操作用的；當數據機已經與其他設備連接時，其處于連線模式，所有在此時由計算機送至數據機的信息都將經由電話線傳送到另一部計算機上。專門使用於控制數據機的指令集被稱為「 at指令集」 ，對moden的所有操作（如撥號、應答、掛機等）都可以通過給moden發送ascii字元串來實現， moden在收到at命令后，先對命令進行判斷，接著分析和執行命令緩沖區中的命令，最後以自身的ascii字元對命令作出響應。
  3. According to the actuality of the present research on ct, we bring forward a new design scheme based on the rogowski coil, in this design, the protection in short circuit failure and the measurement in normal condition are both fulfilled. it can also communicate with the computer through the communicating interface, sending the parameter of the system current and accepting the instruction

    本文在考察了國內外電流互感器發展現狀的基礎上，提出了一種基於rogowski線圈的電流互感器，該互感器具有正常電流的測量和短路故障時的保護功能，並且預留了與上位機的通訊介面，接受上位機的指令並向上傳送電網的電流參數。
  4. In order to satisfy this requirement, the complex signal lines are usually used to detect the speed and position of each motor and to command the desired speed and position

    在多電機同步控制中，各電機之間實時的數據通信是很重要的。為了滿足這個要求，檢測每個電機的速度和位置數據以及傳送指令都需要大量復雜的數據信號線。
  5. Based on the developed system, and equipped with module for wireless transmitting and receiving, the experimental validation for the functions of cdma techniques are carried through. corresponding experimental data is presented. it can be concluded that cdma system can realize the correct receiving, meanwhile cdma system will not interference with another receiver in the system and other receivers will not capture the signal from the working system

    基於所研製的系統，配以無線發送、接收模塊，進行cdma無線制導指令傳輸實驗、對cdma的原理進行實驗驗證，得出相應的實驗數據，證明了cdma技術一方面能實現信號的正確接收，另一方面又能防止對系統中其它用戶的干擾及非預定接收機對發送數據的截獲。
分享友人
分享到 Line

分享到臉書