控制序列 的英文怎麼說

中文拼音 [kòngzhìxùliè]
控制序列 英文
control sequence
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 列 : Ⅰ動1 （排列） arrange; form a line; line up 2 （安排到某類事物之中） list; enter in a list Ⅱ名詞1...
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. The hybrid genetic algorithms are employed to get the better optimization control law, and the problem of limited torque is solved by individual representation operation

    為了獲得最優擺起控制序列，採用混合遺傳演算法進行優化計算，通過編碼操作解決控制力矩受限問題。
  2. The following sections describe how to control serialization

    以下各節描述如何控制序列化。
  3. Describes how to control serialization by using attributes

    描述如何通過使用屬性控制序列化。
  4. To further control the serialization, the

    要進一步控制序列化，
  5. The other way to control serialization is achieved by implementing the

    控制序列化的另一種方式是在對象上實現
  6. That controls type substitution during serialization and deserialization

    ，它控制序列化和反序列化過程中的類型替換。
  7. Takes control of the serialization process, and replaces all objects derived from

    預先配置）控制序列化過程，並用代理代替從
  8. Begins the control sequence that determines when and how to print a document

    開始控制序列，確定何時以及如何對文檔進行列印。
  9. Completes the control sequence that determines when and how to print a document

    完成確定何時以及如何對文檔進行列印的控制序列。
  10. Provides types that support customization and control of serialization at design time

    提供支持在設計時自定義和控制序列化的類型。
  11. Ergonomic design of control centres - principles for the arrangement of control suites

    控制中心的人類工效學設計.控制序列排列的原則
  12. Predictive control is a form of control in which the current control action is obtained by on - line solving open - loop optimal control problem, and the above procedure is repeated based on new state and out measurements at the next time

    預測控制通過在線求解一個有限時域開環最優控制問題來獲得最優預測控制序列，並將當前時刻的控製作用於對象，在下一采樣時刻基於新的狀態或輸出測量值重復上述過程。
  13. For a prescribed sequence of fuel supply rates, it has been shown that a strategy of optimal type depends on two real - number parameters, a. and n. the parameter n determines the hold speed for the journey, and the parameter a determines the sizes of the coast - power pairs used to approximate speedholding

    在給定控制序列及單位能耗后，已經證明優化類型方案由兩個實數參數和決定。參數決定了平均速度而參數決定了用來近似平均速度的開始加速和開始滑行的速度之間的差距。
  14. Within the specified time limit, the strategy determines and implements an optimal feed - forward control sequence to the system, swings up the double inverted pendulum from its hanging position, and achieves zero speed state at the upright position

    該策略通過在規定的時間內向系統施加一前饋控制序列，使上、下擺桿從自然懸垂位置擺到倒立點位置並使速度為零。
  15. Begins the control sequence that determines when and how to preview a print document

    開始控制序列，該序列確定何時以及如何預覽列印文檔。
  16. Completes the control sequence that determines when and how to preview a print document

    完成控制序列，該序列確定何時以及如何預覽列印文檔。
  17. Begins the control sequence that determines when and how to print a page of a document

    開始特定控制序列，該序列確定文檔頁的列印時間和列印方式。
  18. Begins the control sequence that determines when and how to preview a page in a print document

    開始控制序列，該序列確定何時以及如何預覽列印文檔中的頁。
  19. In the description of circuit design, the emphasis is paid the following hardware modules : ad / da inverter, dsp module, external program / data memory, cpld control logic, serial communication module, power module, and so on. problems and the corresponding solutions found in the design and debug stage are discussed, too. finally, the low - level software driver design is presented in detail, including system booting, initialization of dsp registers, cpld logic and timing control, drivers for asynchronous communication fifo, and drivers for ad converter

    在電路模塊分析中，重點介紹了語音的輸入放大和輸出緩沖部分、 ad da轉換、 dsp語音壓縮解壓、外部程序數據存儲器、 cpld邏輯控制、串列收發組件、電源供電以及dsp的jtag介面等等，並且給出了在硬體電路設計和調試過程中的問題與解決辦法。
  20. Completes the control sequence that determines when and how to preview a page in a print document

    完成控制序列，該序列確定何時以及如何預覽列印文檔中的頁。
分享友人
分享到 Line

分享到臉書