摩擦圓法 的英文怎麼說
中文拼音 [mócāyuánfǎ]
摩擦圓法
英文
friction circle method-
This method is of high reliability and efficiency. it ' s regarded the one of the best designing method nowadays. to choose the best parameter of frication piece and make sure that the cloth ' s mechanical function is the aim of friction piece ' s parameter priority
為了圓滿解決上述兩個問題，本文採用廣義既約梯度法對摩擦片參數、變速器傳動比及變速器二軸六檔齒輪進行了優化設計，該演算法可靠性和效率都很高，是目前公認最為優秀的優化方法之一。Moreover, based on the assumption that the slip velocity at the disks increases linearly with the radius up to the rim slip velocity, another pressure distribution is derived by introducing a appropriate velocity field. then these different results by the different friction conditions and technique are compared. 2
同時，在圓盤邊緣處滑移速度一定，介質的滑移速度隨著半徑線性變化的假設下，引入合理的速度場，得到了另一種圓盤上的壓力分佈規律，並對不同的摩擦條件及用不同方法計算得到的結果進行了對比。Based on the review, the fluid flow and heat transfer in the curved circular and rectangular pipes have been researched by employing perturbation method and numerical simulation with a physical model under the rotational orthogonal curvilinear coordinate in a rotating curvilinear pipe with multi - parameters. we firstly analyzed the fully developed fluid flow and heat transfer, mixed convection heat transfer, the development of flow and heat transfer in the inlet in different cross section ( circular, elliptical, annular and rectangular crossection ). the variations of the secondary flow, axial velocity, distribution of temperature, the friction force on the wall, the ratio of friction factor as well as the nusselt number with different dimensionless parameters had been examined in detailed
本文在總結和分析了一個世紀以來有關曲線管道流動和換熱特性的研究成果的基礎上，以旋轉正交曲線坐標系統下的多參數旋轉螺旋管道中的對流傳熱為物理模型，通過攝動方法和有限體積法，首次對各種截面（圓截面、橢圓截面、環形截面、矩形截面）旋轉曲線管道內充分發展流動的流動結構和傳熱特性（包括耦合對流傳熱特性）以及旋轉曲線管道開口段發展流動的流動結構和換熱特性進行了系統的數值模擬和理論分析，詳細討論了各種無量綱參數對管道內軸向速度分佈、二次流結構、溫度分佈、壁面摩擦力、摩擦系數比以及管道nusselt數的影響，獲得了若干創新性成果。With the help of this program, this paper does research on the moved backwards of the slide surface, lengthening the anchor section, the soil nail ' s total force, gets conclusion about relations between the soil nail ' s length and the slope ' s grade, height, soil ' s mechanical parameter ; relations between soil nail ' s total force and coulomb soil pressure. with the help of the large multiuse finite element program ansys, this paper analyzes the soil nailing in one - step ' s slopes, in two - steps " slopes, puts the emphasis on the axis force ' s distributing along the soil nail at each rows, the effect of both the excavating mode and the original slope figure to the axis force of the soil nail, the one another effect between the upper - step slope and the nether - step slope in the soil nail ' s axis force, gets conclusion about the design of soil nail at the first low, different slope body is the same with different excavating mode, the original slope figure has more effect to some than others because of the slope body, the reasonably design of the step width in two - steps slopes, the two - steps excavating and retaining has more virtue than the one - step ' s. through soil pressure analysis this paper does research on the differences and the links between the coulomb soil pressure theory and the rankin ' s, the vertical pressure at the slope surface when the slope surface is inclined and the retaining wall is rough, the soil pressure ' s distributing behind the panel, gets conclusion about the effect of both the slope body inner stability and the slope surface local stability to the soil pressure
通過分析比較，論證了對數螺旋線型比圓弧形作為邊坡的假設滑裂面具有較多的工程優點，並為此編制了一個採用極限平衡法分析土釘支護的fortran語言程序，以此作工具對滑裂面的后移、土釘錨固段的超長、土釘總力的大小等方面作了研究，得出了有關土釘的長度與邊坡的坡角、坡高、土體力學參數的關系、土釘總力與庫侖土壓力間的關系等結論；採用大型通用有限元數值分析程序ansys分別對採用土釘支護的一階邊坡、二階邊坡進行分析，重點是研究各排土釘的軸力分佈規律、開挖方式及原始邊坡形態對土釘的軸力的影響、上下階邊坡在土釘軸力方面的相互作用，得出了有關第一排土釘的設計問題、不同類型的土體應適用於特定的開挖方式、原始開挖出的邊坡形態對一些類型坡體的邊坡土釘支護有較大的影響而對另外一些影響不大、二階邊坡臺階寬度的合理確定、二階開挖及支護比一階時具有較多的工程優點等結論；通過土壓力分析對朗肯、庫侖兩種經典土壓力理論的區別與聯系、坡面傾斜及墻背有摩擦時的坡面豎向應力分佈、面板背土壓力的分佈形態作了研究，得出了邊坡支擋土壓力受坡體內部穩定與坡面局部穩定兩個方面的影響、土釘支護面板背土體中卸荷拱的存在對面板受力有利等結論。Circular saw friction cutting
圓形摩擦鋸割切法Friction circle method
摩擦圓法After the topological structure of machine system and the method of conversion of coordinate are introduced, 3d model of the manipulator had been set up in pro / e. in the process, several problems had been solved, such as simplification of part model, assembly, idealization of rub disc movement decomposition organization
在介紹了軟體中機械繫統的拓撲結構和坐標變換的方法后，在pro e中建立了機械手的3d模型；解決了模型建立過程中的零件模型的簡化、零件的裝配、摩擦圓盤機構的理想化、模型中電動機的轉動方向等問題。分享友人