擬塑性流體 的英文怎麼說

中文拼音 [nǐsùxìngliútǐ]
擬塑性流體 英文
pseudoplastic fluid
  • 擬 : 動詞1. （設計; 起草） draw up; draft 2. （打算; 想要） intend; plan 3. （模仿） imitate
  • 塑 : 動詞（塑造） model; mould
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 體 : 體構詞成分。
  • 流體 : [物理學] fluid; fluor流體力學 fluid mechanics; hydromechanics; 流體生物學 hydrobiology; 流體運動學 hydrokinematics
  1. During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied

    在溫度場的模擬中，模擬結果表明，保壓時間是影響製件成形質量的關鍵因素之一，擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大，需進行參數之間的協調，只有當變形區內部始終維持準固態時，才能實現穩定的液-固擠壓成形過程；在變形場的模擬中，根據液態浸滲擠壓的成形特徵，選用了雙曲正弦剛-粘塑性有限元計算模型，研究了變形過程中應力應變場的變化規律，研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。
  2. According to the practical geological model of slope, by means of the finite element analysis, from the constitutive equations of the elastoplasticity and the viscoelasticity - viscoplasticity, the process and mechanism for progressive failure of the locked segment of rockmass are quantitatively revealed and simulated during the rupture, deformation, destruction, and failure of highsteep slope rockmass, and the dynamics driving the motion of rocky landslide with violent starting velocity by high pressure water flow is dealed with

    根據邊坡實際地質模型，基於彈塑性與粘彈-粘塑性理論的本構方程，通過有限元模擬分析，定量地揭示和模擬再現了高邊坡巖體破裂、變形、破壞及失穩前後鎖固段巖體漸進性破壞的機制和過程，探討了高壓水流作用下滑坡啟程劇動的破壞機理。
  3. Based on the shale code, the early code of ale, the two dimensional finite difference elastic - plastic flow code hepale has been developed, in which the ideal elastic - plastic model and equation of state of gruneisen are used to describe the solid material, the programmed burn technique is used to simulate the propagation of detonation, and the equation of state of jwl is used to describe the detonation products

    藉助于ale方法的早期程序shale的基本框架，開發研製了二維彈塑性流ale方法計算程序hepale 。程序包含用彈塑性本構模型和gr nrisen狀態方程來描述固體材料的行為；採用jwl狀態方程來描述爆轟產物的性質；採用程序燃燒法來模擬爆轟波陣面的傳播。
  4. Through analysis and compare, the measure fitting for huxi bank was put forward. ( 3 ) introduced fast lagrangian analysis of continua. flac3d is a three - dimensional explicit finite - difference program. it can simulate the behavior of three - dimensional structures built or soil, rock or other material and can simulate plastic collapse, flow and large - strain accurately

    （ 3 ）對三維快速拉格郎日有限差分法進行了介紹，三維快速拉格朗日法是一種基於三維顯式有限差分法的數值分析方法，它可以模擬巖石或土體及其它材料的三維力學行為，可以準確模擬材料的屈服、塑性流動、軟化直至大變形，尤其在材料的彈塑性分析、大變形分析以及模擬施工過程等領域有其獨到的優點。
  5. The methods and feasibilities by which the filling simulation software of plastic injection molding can be adjusted for mim have been discussed

    探討了修改塑料注射成型充模流動模擬軟體作為金屬注射成形充模流動模擬的可能性及方法。
  6. This paper investigated the electrorheological ( er ) characteristics of two suspensions of starch particles ( a ) and aluminosilicate particles ( b ) in silicone oil respectively, and also their transmitting properties on a simulated device of cylindrical er clutch ( erc ) by comparison, only to show that a is a kind of electrorheological fluid ( erf ) with definite plastic yield - point and can be subjected to a narrow voltage range on erc, while b is a kind of pseudo - plastic erf and can be subjected to a wilder voltage range on erc

    本文研究了硅油-澱粉（ a ） 、硅油-硅酸鋁（ b ）兩種er流體的電流變性能，並通過一套筒式er離合器模擬傳動裝置，研究且對比了這兩種er流體在筒式er離合器上的傳輸特性。結果表明a是具有塑性屈服點的流體，其在er離合器上有效調速電場范圍較小； b是假塑性流體，其在er離合器上有效調速電場范圍較寬。
分享友人
分享到 Line

分享到臉書