擰緊螺栓 的英文怎麼說
中文拼音 [nǐngjǐnluóshuān]
擰緊螺栓
英文
to tight a bolt- 擰 : 擰形容詞[方言] (倔強) pigheaded; stubborn
- 緊 : Ⅰ形容詞1 (物體受到幾方面的拉力或壓力以後呈現的緊張狀態) taut; tight 2 (物體受外力作用變得固定...
- 螺 : 1. [動物學] (軟體動物) spiral shell; snail; conch 2. (螺旋形的指紋) whorl (in fingerprint)
- 栓 : 名詞1. (可開關的機件) bolt; plug 2. (塞子) stopper; cork
- 擰緊 : screw home; screw up; tighten; buck-up
- 螺栓 : bolt; screw bolt; threaded bolt
-
1, screw down the flange bolt regularly and the tightness of all bolts shall be same as soon as possible. under bad conditions, flat pad as well as spring gadket shall be installed to prevent the nut loosening
1法蘭螺栓應逐步均勻地加壓擰緊,所有螺栓松緊度盡可能一致。使用條件惡劣的場合,除加平墊外可添加彈簧墊圈,以防螺母松動。Using the optimum calculating method, some important technical parameters could be determined, that is, optimum supporting force, allowable deformation of rock mass, cross section area of u - shape set, pre - tight force and diameter of the bolt as well as torque to provide optimum supporting force
用這一計算方法能求出巖石恆阻支護的重要技術參數,即最優(小)恆阻支護力、圍巖最大允許變形量、恆阻u型鋼支架的截面積、聯接螺栓的預緊力和直徑及最優支護力的擰緊力矩。396 after seven days, the grouted mortar will have concreted, then we shall tighten the anchor bolts
灌漿在七天以後凝固,我們就將擰緊地腳螺栓。Combines with a concrete subject, this paper, composed of seven chapers, makes a deep analysis on theory and experiment of key bolt fastening of engine. the first chapter presents the theory of tightening technology of the available bolt the second chapter gives a narrating about tighten technology availably in survey. pointing that the nature of torque control is axis preload
本文結合一具體課題,第一章敘述了可控螺栓擰緊技術的理論,第二章綜述了可控擰緊技術,提出了扭矩控制研究的實質是控制螺栓的軸向預緊力。High-strength bolts were inserted into the holes and tightened to a high preload level.
把高強度螺栓插入孔洞,同時擰緊螺栓達到高的預加載水平。The plumber took out a wrench and tightened the bolt
管子工拿出一把扳手擰緊了螺栓。Fasten bolt to fix distributor. regulate ignition timing, start up engine and make fine regulation to ignition advance angle at the time of idling speed to make engine to be stable while idling. acceleration should be sensitive and powerful which means a complete regulation is done
調點火正時,啟動發動機,在怠速時對點火提前角做細微調整,使發動機在怠速階段平穩,加速時應明顯感到快捷有力,即調整完畢,擰緊分電器緊固螺栓。Chapter three makes clear the importance of preload, and deals with the theories on the relationship between preload and torque, angle and extension of the bolt from various aspects
第三章由扭矩控制的實質? ?預緊力,點明了預緊力的重要性,預緊力與擰緊力矩、螺母轉角、螺栓伸長的關系,對其進行了理論方面的研究和探討。Add sealed shim between the two flanges and then lock down the bolt
安裝時兩法蘭間需加密封墊片,然後均勻擰緊螺栓。To tight a bolt
擰緊螺栓Don t tighten the bolt too much to prevent the gear broken or cut caused by expansion
在裝輪時不要過度擰緊螺栓,以免輪在正常運轉狀況下,因材料膨脹導致輪破裂或者螺栓被剪斷。The wire junction uses plugged bolt to insure its easy operation. it s small in volume and light in weight easy to be installed
2採用對接式接頭,連接時需將連接排插入接頭,擰緊螺栓即可體積小,重量輕,方便安裝。Insert special bolt into the preset hole of c form parts, where the bolt will be fixed into the threaded hole of wedge, then screw the bolt on with a socket spanner until the first nut drops
將專用螺栓插入c形無件預留孔與楔塊的螺紋孔相連,用套筒扳手擰緊螺栓直到第一個螺帽自行斷落。The transmission part cannot be hoisted and damaged. add sealed shim between the two flanges and then lock down the bolt equably
安裝時傳動部分不允許作吊裝用,並嚴禁損傷。兩法蘭連接中間需加密封墊片,然後均勻擰緊聯接螺栓。In chapter four, the parameter in the bolt fastening process is set down and the controlling methods and comparison is analyzed
第四章討論了螺紋裝配過程參數的設定和螺栓擰緊的控制方法及比較,並對擰緊控制方法的選用進行了分析。The preparing work before test run : first organize test run guide group consisted of supply party, demand party and installation party to check the installed qualified equipment ( machine, electricity, liquid, gas ) in an all - round way to see that circuit, water - way, gas - way and oil - way are switched on ; that all fastener, bolts and nuts are tight ; that all lubricating points and cooling points are put in position
試運轉前的準備工作:首先應組織有關(供方、需方、安裝)等單位參加的試車領導小組,對已安裝合格的設備(機、電、液、氣)進行全面的檢查,電路、水路、氣路、油路是否接通,所有設備的緊固件、螺栓、螺母等是否擰緊,各潤滑點和冷卻點是否到位。The bolt is worn and not an exact fit but it will serve its turn until i can buy a new one
這個螺栓已經壞了,不能擰緊了,但是我還未買來新的之前暫時再用一下。Place the new pump in position and tighten mounting bolts
使水泵就位,擰緊裝配螺栓。分享友人