支承強度 的英文怎麼說
中文拼音 [zhīchéngqiángdù]
支承強度
英文
bearing strength-
In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test
然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。The epoxy resin floor can be divided into skidproof and anti - static, etc. tiffany is equipped with a strong force of professionals, experienced engineers and workers as well as advanced production facilities. it is mainly engaged in the processing of anti - static, erosion - proof, skidproof, high - strength floors and water - proof surfaces. tiffany s aim is " advanced technology, high - quality products and best service "
公司擁有一批高素質的專業人才和一支富有實際經驗的施工隊伍，設備先進，主要承接電子電器、精密機械儀器、食品、符合gmp標準的醫藥等行業的防靜電、防腐、防滑、高強度地面處理和墻體處理工程。By the check - out, inspection and measurement to start construction the industrial art to this test pile with the examination between stake body mass and bearing power, made sure the stroke reasonable operation method drilling under the dissolved cavern geology term ; the pier foundation loading test expressed the lading and rub the lading that resistance drag a glazing for of relation, and to the borehole cast - in - place concrete pile in the karst terrain deliver with break the mechanism, the characteristic of bearing power, proceeding the spot test job of the full of result ; the test data expresses the stake side friction resistance to rises with a bat batch terminal friction resistance very important function, the of tip of pile resistance drag occupies the proportion very few
通過對本次試樁施工工藝的檢測和樁身質量及承載力的檢驗，確定了沖擊鉆在溶洞地質條件下的合理使用方法；基樁承載實驗表明了荷載與摩擦阻力之間的關系，並對巖溶地區的嵌巖灌注樁的荷載傳遞和破壞機理、承載力特性，進行了富有成果的現場測試工作；試驗數據表明樁側摩阻和支盤端阻起很重要的作用，樁端阻力所佔比例甚少。這與設計樁基時的計算模式相差很大，承載力也較設計增加；使用力學數值分析方法和有限單元法，對鉆孔灌注樁樁端下的巖體強度和結構穩定性方面進行模擬計算和定量研究。Besides, this paper adopts the random finite element method, uses geometric and physical mechanical parameters that are relevant to lining weight of surrounding rock, coefficient of lateral pressure, height or buried depth of vertical loading, elastic resistance coefficients of surrounding rock, elastic modulus of support structure, unit weight of concrete, thickness of the structure as well as torsional strength and compression strength of concrete and etc., as random variables, applies the monte - carlo method to sampling by computer, preliminarily evaluates the reliability of bearing capacity and stability of molded concrete lining of the xuefeng mountain tunnel, and obtains the related displacement of the lining, mean value and variance of internal force, and computed the reliability index of lining structures
此外，本文採用隨機有限元方法，將圍巖容重、側壓力系數、垂直荷載高度或埋深、圍巖的彈性抗力系數、支護結構的彈性模量、混凝土容重、結構的厚度以及混凝土的抗扭與抗壓強度等與襯砌結構有關的幾何與物理力學參數作為隨機變量，應用蒙特卡洛理論進行計算機隨機取樣，對雪峰山隧道模注混凝土襯砌的承載力與穩定性的可靠度進行了初步評估，得出了襯砌的相關位移與內力的均值和方差，並計算出了相應的襯砌結構可靠指標。Both of forward and back bearings have been integrated into one box to make full use of the length of base frame that the motor formerly mounted on, and short the shaft extended lengths in both end with the strengthening connection between bearing housing and screw thread of base
將前後兩支承設計為一個整體軸承座，充分利用原電動機安裝底座的有效長度，最大限度地縮短了軸的懸伸量，提高了軸承座與底座的螺紋聯接強度。The research result indicated : for the strip primary mirror discussed in this article, the hexagon light - weighted cell has the best structural rigidity quality, the square cell is a little worse, the triangle cell is the worst ; there is an optimum on primary mirror thickness ; on condition of 1g gravity load combining with 4 centigrade uniform temperature rising, the thinner and higher of the flexible support reed, the better of the primary mirror surface figure. the decision of the structural parameters of the flexible support reed must take static rigidity, dynamic rigidity, static strength and dynamic strength of primary mirror assembly into account
研究結果表明：對于本文的長圓形主鏡，採用正六邊形輕量化孔，鏡體結構剛性品質最好，正方形次之，正三角形最差；主鏡鏡體厚度存在最佳值；主鏡組件在1g重力、均勻溫升4共同作用的工況下，主鏡柔性支撐簧片厚度越小、高度越高，主鏡綜合面形誤差（ p - v值）越小，但同時主鏡組件的剛體位移增大、固有頻率下降，因此柔性支承結構參數的確定要綜合考慮主鏡的綜合面形誤差和主鏡組件靜態剛度、動態剛度、靜態強度和動態強度等因素。On the contents of two sides abovementined, this paper attempts to do some initial researches from three angles as follows : 1, the analyses of anti - seismic features on longitudinal direction of the aqueduct l ) the seismic longitudinal effects are small. the vibrant characters are decided from the structure integration and rigidness of piers and main arch - ring of the aqueduct, so the following measures should be taken in order to weaken and isolate seismic influence : properly broadening the section sizes and adopting the high class concrete, lowering the height and barycenter of building, setting hoop steel bars so as to increase the plasticity of the concrete which can absorb the seismic energy and prevent the damages due to stress centralization on the linkages and changing place
本文試圖就上述的這兩大方面的內容，從以下三個角度進行了初步研究： 1 、縱槽向抗震性能分析1 ）湯峪河吊桿拱支承結構的縱槽向地震效應較小；吊桿式拱架結構動力特性取決于槽墩和主拱圈的剛度，以及結構的整體性，故適當加大構件截面尺寸或提高砼標號，盡量降低結構的建築高度和重心，在構件連接和變截面處增設梗脅，按照約束混凝土的要求來加強箍筋的配置，增加砼的延性，以克服地震時構件連接和變截面處的應力集中造成的坡壞，並吸收大量的地震能量，從而起到隔震，減震的效果。The principal conclusions include : ( a ) the composite system is composed of both active - bearing structural members and inactive - bearing ones, being of a character of combination of rigid retaining structures with flexible ones, so its working mechanism will be behaved as sharing loadings, waterproof and impermeability, loading transfer, local reinforcement and pre - reinforcement ; ( b ) the experimental results show that much more subsoil will participate in retaining action, soil stresses of internal slope will be shared uniformly and deflections caused by excavation will be reduced notably because of cooperation of nails and cement - soil mixing pile wall ; and ( c ) the internal forces of facing in vertical model will be a control factor of design and the cross section tensile strength of cement - soil wall will govern strength of the
主要研究結論有： （ 1 ）復合土釘支護的作用機理主要為臨時加固土體以保證局部穩定、有機聯系以共同承擔荷載、改善土體性質起到止水抗滲作用。 （ 2 ）試驗結果表明：復合土釘支護能夠充分調動周圍土體共同作用，有效地控制基坑變形；復合土釘支護中止水帷幕的插入深度和強度對控制邊坡變形與失穩有較大作用；復合土釘支護效果明顯優於一般的土釘支護。 （ 3 ）面層與邊坡土體共同變形，設計時可按外力作用下的彈性地基梁進行計算。On the basic of former research men ' s experience, 18 experimental members ( including 9 simple beams and 9 restrained beams ) are designed and tested. in the experiment, phenomena are observed and record by taking photos in the whole process from the first crack appears to test members crash completely, experimental data is attained including load values of crack - appear load, critical load and terminal load, stress values of reinforcing steel bar stress, compressed concrete stress and beam flank stress and values of deflection etc. by analyzing the crack ' s appearing and developing form and stress values of concrete and steel bars, the crash modes of test beams are defined ; shearing force - deflection curves are contrasted and analyzed ; the effects on shear strength of the three factors as shear span ratio, concrete strength and restraining moment are also analyzed
借鑒已有試驗的經驗，本文設計和完成了對18根超高強混凝土無腹筋梁（包括9根簡支梁和9根約束梁）在集中荷載下抗剪強度的試驗，觀察了試件從裂縫出現到完全破壞失去承載能力全過程的試驗現象並通過拍照進行記錄，獲得了試件的斜裂縫出現荷載、臨界斜裂縫荷載和極限荷載等荷載值和縱筋應變、混凝土受壓應變和梁側混凝土應變等應變值以及撓度值等。The computing results of the thesis shows that qtjs 160t railway crane ' s carrier frame has met the intensity requirements. the local stress of the contact position of carrier frame, outriggers and pins is presented. the dangerous positions of the carrier frame are pointed out
論文分析、計算結果表明， qtjs160t鐵路起重機底架結構滿足強度要求，論文給出了車架、支腿和銷軸聯接處的局部應力情況，指出車架在回轉支承圈處存在應力集中部位。Study of practical formula about strength and rigidity of 6 - point - supported - glass using the super sap fea software to solve different calculation models - which have different parameters, such as a / b, a / c and so on, this paper achieves a series maximum deflection coefficients and maximum stress coefficients, then form calculation formulas of maximum deflection and maximum stress under the load of wind
6點支承玻璃強度剛度實用的計算公式研究採用supersap有限元分析，求出不同的計算模型（玻璃板的尺寸參量a b ， a c不同） ，得出一系列最大撓度系數和最大應力系數，形成6點支承玻璃在風載荷作用下的最大撓度計算公式和最大應力的計算公式。Through the experimentation for the physical performance of cfpb masonry under local compression, the author has observed the deformation and failure of cfpbm. based on the mathematical statistics and regression analysis of the experimental data, the author derived a feasible and common formula for counting the cfpbm ' s local compression strength regarding the different local compression locations, analyzed stress distribution of local bearing masonry under beams end, and provided the calculating formula on effective supporting length of beam end in brick masonry. as the results of experiments demonstrate, owing to the cfpb ' s own holes " system, the beneficial effects, the bounding effect of surrounding masonry and the spread effect of force, have not developed completely
試驗結果分析表明：由於多孔磚自身的孔洞結構，砌體內部的圍箍作用和力的擴散作用未得到充分發揮，局壓強度雖較軸心受壓強度有所提高，但仍低於同情況下實心磚的局壓強度；當有上部荷載作用時，對砌體局壓有利的懸臂卸荷作用和內拱卸荷作用均不明顯，因此在推導梁端局壓強度計算公式時，未考慮此可能存在的有利影響，計算偏安全；局壓強度提高系數公式除採用規范公式（二項式）的表達式，還用對數式進行了回歸推導，得到了一個較為普遍的公式；論文還對梁端局壓的梁端有效支承長度計算公式進行了回歸推導。Through theoretical analyses in the article, the highly tough top - coal deflection before destroying is in inverse proportion to elastic mould, in direct proportion to tensile strength, and the conclusion that bigger deflection roof can ' t sufficiently transmit the compressible support to top - coal is drawn
通過理論分析，獲得了高韌性煤層煤體在破壞前的撓度與彈性模量成反比，與抗拉強度成正比的關系，並得出撓度較大的頂板不能很好把支承壓力傳遞給頂煤的結論。But to use this alginate hydrogel as a scaffold, we needed to give it shape and internal structure, while enhancing its mechanical strength so that it would keep its shape under the weight of seeded cells
但在利用褐藻酸鹽形成的凝膠做為支架時，我們需要賦予它形狀和內部結構，同時還要加強它的機械強度，使它在承受了植入細胞的重量后，還能維持特定形狀。The paper has disgussed the methods of strengthing space structure and glass roofs stiffenss. then has analyzed the rationality of supporting structure of glass roof. according as the existing nodes, new nodes have been given. resisting sllippage is tested simply, node conformation has been amended
論文從結構力學位移計算公式出發，討論了提高空間結構剛度的有效途徑，並提出增強採光頂支承結構剛度的措施，進一步分析了新型採光頂支承結構的合理性。The frame fixing structure is that frame supports around the glass, and all glass edges are wedged into the frame that supports adequately the intensity and rigidity
有框架安裝結構是指玻璃的周邊都有框架支承，並且要求玻璃邊部全部被框架口包住封閉，同時框架具有足夠的承載強度和剛度。Secondly, for 74500dwt bulk carrier, the strength calculation and analysis of bottom structure in forward area, which bear big act force during ship launching, are carried out
其次，對船在下水過程中承受很大支反力的艏部區域底部結構進行了強度分析計算。Standard test method for evaluating dowel - bearing strength of wood and wood - base products
木和木製品的榫支承強度評定的標準試驗方法Standard test method for bearing strength of plastics
塑料支承強度的標準試驗方法Aerospace ; fibre reinforced plastics ; testing of multidirectional laminates ; determination of bearing strength
航空航天.纖維增強的塑料.多向層壓板的試驗.支承強度分享友人