數值法分解 的英文怎麼說

中文拼音 [shǔzhífǎfēnjiě]
數值法分解 英文
numerical method analysis
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 解 : 解動詞（解送） send under guard
  • 數值 : numerical value; numerial number; figure; magnitude; value數值表 numerical tabular; 數值天氣預報 ...
  1. Second, adopting the linearity of oil film of the guide bearings, the transient response of the shafts is computed and analysis by integrating with willson method. because of the uncertain position of the shafts in the guide bearing, the model and solution method of nonlinear transient response of the shafts is discussed

    然後結合willson數值積分法，採用線性化油膜力，對機組軸系的線性瞬態響應進行了計算分析，根據機組軸系在瞬態響應中運動的不確定性，給出了由導軸承油膜力非線性所引起的主軸系統的非線性瞬態響應的建模及求解方法。
  2. The elastic foundation model is considered as two - parameter elastic foundation model and its effect to moderate - thick plates are taken into account by a set of governing differential equations. united with hu hai - chang ’ s function, least squares collocation weighted residual method which uses b - spline function as trial function is put forward for solving the bending problems. compare with the results of finite element method of lines, spline finite strip method, accurate solution of series etc. it is proved that the method in this article has adequate accuracy and practical feasibility

    本文採用瑞斯納中厚板理論求解彈性地基板，建立雙參數地基與中厚板相互作用的控制微分方程，結合胡海昌的解耦函數，運用雙五次b樣條函數作為試函數的離散型最小二乘加權殘值法分析了雙參數地基上的中厚板的彎曲問題，並將結果與有限元線法、有限條法、級數精確解等進行比較，證明本文方法具有足夠的精確性與實際的可行性。
  3. Adopted numerical value integral method into the explain of the basic heat - conduct differential equation based the stabilization flow. get temperature changes rule of the cold - blowing and hot - blowing period of the cold - cumulating and dry - able tin

    採用數值積分法對基於穩定流的基本傳熱微分方程組進行求解，進一步了解了影響蓄冷器效率的主要因素。
  4. Abstract : according to the continuative condition of the tangential fields on the slot aperture which is the inclined narrow - slot on the broadwall of a sectoral waveguide, the moment method is used to calculate the magnetic current coefficient and distribution. then the scattering field, the scattering parameter and the equivalent impedance are obtained. leting only the te11 dominant mode propagates in the waveguide, the scattering parameters and the normalized equivalent series impedance in the x - band are computed. the basis disigned the slot antenna and the slot array is offered

    文摘:根據縫隙口面切向場的連續條件，採用解析數值法矩量法，對扇面波導寬壁上窄的斜縫進行了計算，解得了磁流系數及其分佈，並得到散射場、等效散射參量及等效阻抗等重要參數.假定波導中僅有te11主模傳輸，在x波段計算了散射參量和歸一化等效串聯阻抗，給出計算結果，為縫隙天線和縫隙陣列設計提供了依據
  5. This paper put forward a semi - analytic semi - numeric method to analyze the cold bending of the hubcap

    該文提出一種半解析半數值的分析方法，對汽車輪輞擋圈的冷彎過程進行了分析。
  6. Borrowing the traditional two - speed approach originally developed in conventional attitude integration, we design one new numerical integration algorithm to solve the three kinematic equations. the new navigation algorithm based on dual quaternion is thus constituted

    借鑒成熟的姿態四元數積分的雙速演算法結構，設計了一個數值積分演算法求解以上三個運動學方程，構建了基於對偶四元數的捷聯慣性導航演算法。
  7. According to the laplace transformation method and superimposition principle, theoretical solutions of the effect of three typical bin ' s surface protecting methods of thermal insulation were given. based on the solutions, the characteristics and rules of three insulation procedures were analyzed in numerical calculation. the research results of this paper are valuable for engineers to design economical and viable bin ' s surface insulation way

    利用拉氏變換方法及疊加原理，求解出保溫板保溫、倉面噴霧、流水養護這三種常用倉面保護方式降溫效果理論解答；並基於此理論解答，對三種倉面保護方式的特點及規律進行了研究，從數值上分析了幾個影響溫度變化的主要因素：保溫板厚度、內外溫差梯度，距表面不同深度等對每種保護方式降溫效果的影響。
  8. The accuracy of reliability calculation was improved in the derivative sfem method. the local derivatives of fem and numerical method were used to obtain the iterative formulas of the performance function ' s local derivatives. the procedure is relatively simple and adaptable to engineering application as the stiffness matrix formed and decomposed only once

    偏導sfem可靠度法求解構件疲勞可靠度，可靠度計算精度得到改善，通過有限元求偏導，結合數值微分技術，推導出了功能函數的偏導迭代格式，只需一次形成和分解總綱，計算較簡便，適合工程應用。
  9. The streamlines of the flow are obtained from an exact analytical treatment of the stokes equations by making use of finite element methods and complex function theory. based on the calculations, the formation and evolution of vortices in the flow are visualized

    運用有限元方法，從斯托克斯方程，連續性方程和流函數方程出發，通過有限元離散、等參元映射、數值積分和牛頓迭代，得到有限元方程的精確數值解，利用后處理軟體對得到的數值結果進行了可視化處理。
  10. A detailed model of non - linear parametric excitation vibration coupling the stay cable and the girder, in which the static sag as well as the geometric non - linearity are considered, is proposed in this paper. based on several numeric examples investigated by the galerkin method composed with the integration strategy, several kinds of factors effecting stay cable parameter vibration are studied. another parameter vibration model by the axial excitation is presented and the corresponding nonlinear equations are derived

    本文創新地提出了斜拉橋拉索-橋面耦合參數振動模型，推導了索-橋耦合非線性參數振動方程組，聯合galerkin法及數值積分方法，對各種特性的拉索進行了數值求解，得出了影響拉索參數振動的各種因素；提出了斜拉索受軸向端激勵參數振動模型，導出了模型的非線性振動方程，使用諧波平衡法得出了產生參數振動需要的最小激勵幅值、共振時瞬態及穩態的振動幅值及索拉力的變化特性，並用數值積分方法對實際斜拉橋拉索進行了計算，分析了拉索阻尼對參數振動的影響。
  11. The precision duhamel integration solution for the linearization equation is also given from the theory of linear differential equation. the calculating results show that the new method can improve the calculation precision greatly. in fact, the truncation error is not limited by this method, it can arrive the precision according to the requirement

    本文的主要工作有以下幾個方面: （ 1 ）由於非線性項的存在，使得多數情況下難以得到非線性動力方程的解析解表達式，目前常使用數值積分方法來求解非線性動力學方程的解，但常規計算方法的計算精度不很理想，本文提出了含taylor展開項中高階余項的非線性動力方程的線性化數值計算方法，構造了瞬態線性化方程，給出了duhamel積分的表達式。
  12. Based on the asymptotic properties for numerical integral formulas, this paper obtains a class of finite difference methods for solving initial value problems of odinary differential equations, and studies the consistency and stability of new methods

    摘要基於數值積分公式中間點的漸近性質，獲得了一類求解常微分方程初值問題有限差分方法，研究了新方法的相容性和穩定性。
  13. For the mathematics model of differential / algebraic equation system, the penalty function is introduced in numerical computation, and runge - kutta method and newton - raphson method are used respectively in solving the ordinary differential equations and nonlinear equation systems. the process and the results are carried out under corba environment

    本論文採用近年發展的懲罰函數方法進行數值積分，對于常微分方程，採用runge - kutta方法進行數值積分，對于代數方程，採用newton - raphson迭代方法求解，並在corba環境下實現。
  14. ( 3 ) by means of expanding the aperture function into a finite sum of complex gaussian functions, the propagation of fgbs through a paraxial optical abcd system with hard - edged aperture is studied, and the approximate closed - form equations of apertured fgbs are obtained for the first time. the results obtained by using the approximate closed - form equation and collins formula are compared, and the condition under which the approximate closed - form equation is applicable is analyzed

    （ 3 ）利用光闌函數的復高斯函數展開法對截斷平頂高斯光束的傳輸作了研究，首次得到了截斷平頂高斯光束在近軸abcd光學系統中傳輸時的近似解析傳輸公式，通過比較用近似傳物公式和colhns公式直接數值積分所得的結果，得出了近似公式的適用范圍。
  15. A conclusion can be safely obtained : under the condition of considering geometric size c, which is a measurement from the center of a hole to the nearest side in the 6 - point - supported - glass, the analytic approach and the numerical analysis approach ( i. e. fea ) have a smooth unanimity, thus supplying a theoretical basis on which practical formula can be deduced through fea

    得出結論： 6點支承玻璃在考慮孔邊距c影響的條件下，採用解析法與採用數值法進行計算，有較好的一致性。從而為採用有限元分析推導實用的計算公式提供了理論依據。
  16. The reason why the periodic solutions on some of the bifurcation branches cannot be located by using direct integration is also discussed from the viewpoint of the finite dimensional basin of attraction

    此外，用時滯系統的有限維吸引域方法初步探索了為何部分理論分析預測的周期解無法通過數值法得到。
  17. This paper uses complex simpson numerical integration, trapezium area formula and optimization theory to precisely compute according. to mathematical model. it provides data and reference to help check turning conditions of platform lorry, and realizes real time, dynamic inquiry of platform lorry design

    利用復合simpson數值積分方法、梯形面積型心公式和最優化理論對數學模型進行了精確求解，為平板車轉彎工況的校核提供數值和理論依據，實現了平板車設計過程的實時、動態查詢。
  18. In view of the difficulty to solve fuzzy finite element equation by using the existing methods, a new solution approach based on th perturbation method was proposed

    該方法假定當不確定參數相對于其清晰值的分解度不很大時，可以將其在清晰值附近作攝動展開。
  19. What ' s more, the regularization algorithm is utilized when calculating the physical quantities in the interior point very close to the boundary. the numerical results demonstrate that the accuracy and effectiveness of the algorithm is better than the conventional gaussian quadrature

    在求解滾柱內近邊界點的力學參量時，引入幾乎奇異積分的正則化演算法，計算結果顯示該演算法明顯優于通常的高斯數值積分法。
  20. This kind of simulation is a typical stiff system and the stiff integration method with variable order and step size should be applied. on the basis of analyzing the solution of stiff problems of the full dynandc simulation in essence, the gear method, a numerical integration method that is suitable to solve stiff differential equations is studied

    在深入研究微分方程數值積分的基本理論和剛性微分方程的數值積分方法的基礎上，本文根據微分方程的數值方法的收斂性和穩定性的基本理論，對適用於求解剛性微分方程的數值積分方法? ? gear法進行了深入的研究和分析。
分享友人
分享到 Line

分享到臉書