斜截式 的英文怎麼說

中文拼音 [xiéjiéshì]
斜截式 英文
slop-intercept form
  • 斜 : 形容詞（跟平面或直線既不平行也不垂直的） oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
  • 式 : 名詞1 （樣式） type; style 2 （格式） pattern; form 3 （儀式; 典禮） ceremony; ritual 4 （自然科...
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. The corbel ' s dimension should be ascertained as the manipulative condition of diagonal section. the amount of longitudinal reinforcement be ascertained on the basis of the flexure model, is obtained according to static for balance condition, the calculative expression of the load is obtained. and in terms of the design method in ultimate state the maximum load

    我國規范對于牛腿的設計規定，牛腿尺寸的確定以斜截面抗裂作為控制條件，縱筋用量的確定以彎壓破壞模型為基礎，根據靜力平衡條件得到承載力的計算公式，按照極限狀態設計方法計算得到，箍筋用量則按照構造要求確定。
  3. A vertical piano cadby with exposed keyboard, its closed coffin supporting a pair of long yellow ladies gloves and an emerald ashtray containing four consumed matches, a partly consumed cigarette and two discoloured ends of cigarettes, its musicrest supporting the music in the key of g natural for voice and piano of love s old sweet song words by g. clifton bingham, composed by j. l. molloy, sung by madam antoinette sterling open at the last page with the final indications ad libitum, forte, pedal, animato, sustained, pedal, ritirando, close

    一架立式鋼琴凱德拜牌205 ，鍵盤露在外面。上頂蓋關得嚴嚴實實，擺著一雙淡黃色婦女用長手套，一隻鮮綠色煙灰缸里是四根燃盡了的火柴，一根吸過一截的香煙，還有兩截變了色的煙蒂。譜架上斜搭著一本古老甜蜜的情歌g .克利夫頓賓厄姆作詞，詹萊莫洛伊配曲，安托瓦內特斯特林206夫人演唱g大調歌曲
  4. This thesis studies shear lag effect on three representative forms of cable - stayed bridge cross sections by different theoretical methods

    本文針對斜拉橋具有代表性的三種截面形式，採用不同理論計算方法對其剪力滯效應進行研究。
  5. Based on tests of nine 1 / 2 - scaled model slabs under vertical loads, the paper analyzed load - deformation curve and proposed limit value of height - width ratio under axial loads. 2. based on aseismic tests, the paper put forward a model of concrete frame, silica brick and a combination of the two, proposed that the silica brick works as a 45 compression bar, analyzed the factors which may influence bearing capacity of the slab and advised a formula including the numbers of bays and of storeys of the frame

    通過對墻板模型的抗震性能試驗研究，建立了由鋼筋混凝土框格、砌塊以及兩者協同作用三個部分組成的承載力極限狀態下的理論簡化計算模型；提出了墻板中填充塊等效斜壓桿寬度按45度計算的統一量化標準；分析了影響墻板承載力的主要影響因素，給出了表達墻板框格層數和跨數不同的斜截面承載力實用設計計算公式。
  6. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  7. According to the new concrete code, the calculation formula are put forward concerning the load - carrying capacity during construction, the load - carrying capacity of cross - section bending, longitudinal shearing, the inclined - section shearing and part shearing during the application of the continuous composite floor slab, which provide the design proofs for the continuous composite floor slab

    摘要根據新混凝土規范，給出了連續跨壓型鋼板與混凝土組合板施工階段的承載力計算公式及使用階段的正截面抗彎承載力、縱向水平抗剪承載力、斜截面抗剪承載力和局部抗沖切承載力計算公式，為連續組合樓板的設計提供了依據。
  8. The seperated pair of main ribs section was made up by bridge panel and girder, because its construction is convenient, used widely in the prestressing force concrete cable - stay bridge of large span

    回答：分離式雙主肋截面是由橋面板與邊主梁組合而成，由於其施工方便，在大跨度預應力混凝土斜拉橋中得到廣泛應用。
  9. A new bridge structure cooperated by the single - towered cable - stayed structure and the rigid frame structure was presented. many aspects of jinma bridge are researched and analyzed, such as the design method, configuration of the superstructure, section choice of the tower, design and construction methods of the deep - water bases, the stiffness of the cooperated rigid frames, strengthening way in the tower. it is concluded that this new structure is the economical, aesthetic and suitable project for the large - span situation

    主要內容和結論如下： 1 、提出了獨塔斜拉橋與兩側剛構相連接的新型協作體系斜拉橋結構形式，並對該橋的方案比選、設計思路、橋面系結構形式、塔柱截面設計、深水基礎的設計及施工方法、協作剛構的剛度選取、塔柱的直束加固等方面作了詳細地計算分析和比較。
  10. The main purpose of this paper is to realize the section properties and moment capacities of profiled sheets by experimental study and academic analysis for three types of profiled metal sheets which are called u450, u860and super combination profiled metal sheets produced by shanghai baosteel metallurgical construction corporation. its main contents include : ( l ) according to " european recommendations for the testing of profiled metal sheets ", the moment capacities of 32 full - size u450 and u860simple and continuous specimens are tested. ( 2 ) using the finite element program ansys and nonlinear finite element method, the moment capacities of super combination profiled metal sheets profiled are analyzed

    主要內容有： （ 1 ）依據《金屬壓型鋼板試驗歐洲建議》 ，進行了32塊1 : 1的u450 、 u860二類壓型鋼板試件簡支、連續板彎曲性能試驗研究； （ 2 ）採用有限元程序ansys對超級組合壓型鋼板受彎性能進行了非線性有限元分析，分析中考慮了大變形與幾何初缺陷，得出其荷載?撓度曲線與極限荷載p _ （ max ） ，通過截面特性與曲線斜率、極限荷載的關系式得到截面特性；並將分析結果與同濟大學試驗結果進行對比分析。
  11. Steel fiber reduces the size effect of shear resistance of reinforced concrete beams without web reinfocements. the size effect formula is proposed in this paper, it is better agreement with test data. 5

    鋼纖維對鋼筋混凝土無腹筋梁斜截面承載力「尺寸效應」具有降低作用，本文提出了與現行規范相銜接的鋼筋鋼纖維混凝土腹筋梁斜截面承載力「尺寸效應」計算公式，與現有的試驗資料符合良好。
  12. The research works and conclusions of this paper as following : 1. besed on the test results published over the word of reinforced concrete beams without web reinforcements and with stirrups, the systematically statistical analysis is carried out to set up the fomula of shear resistance of reinforced concrete beams using the uniaxial tensile strength of concrete. it provided the basis of strtistical analysis for shear resistance of steel fiber reinforced concrete beams

    根據收集到的國內外對鋼筋混凝土無腹筋梁和鋼筋混凝土有腹筋梁的斜截面承載力試驗研究成果，進行了比較系統的綜合統計分析，提出了採用混凝土軸心抗拉強度研究成果，進行了比較系統的綜合統計分析，提出了採用混凝土軸心抗拉強度指標的鋼筋混凝土梁斜截面承載力計算公式，為鋼筋鋼纖維混凝土梁受剪承載力試驗結果的統計分析提供了基礎。
  13. Based on the tests, the advised formula of normal section bearing capacity and inclined section bearing capacity of high strengthen concrete frame columns are put forward, and the limit of axial compressive ratio and the minimum stirrup ratio in the encrypted region which meet ductility requirement to c60 concrete frame columns are given

    在試驗研究的基礎上，提出高強混凝土框架柱正截面和斜截面承載力計算的建議公式，且給出了滿足延性要求的c60混凝土框架柱軸壓比限值和箍筋加密區箍筋的最小體積配箍率。
  14. On the basis of shear resisting behavior experiments of the column, the formula model for calculating the shear strength of the column is presented, and the undetermined coefficient in the formula is regressed using the experimental data

    在核心柱的剪切性能的試驗基礎上，建立了核心柱斜截面承載力的計算公式模型，並利用試驗數據回歸，確定了公式模型中的待定參數。
  15. Abstract : the formulae of plane stresses on inclined plane are expressed in complex number form. this method has both the advantages of analytic method and graphical method in stress analysis

    文摘:把平面應力狀態斜截面上的應力公式用復數形式表達，並用其進行應力分析，兼有解析法和圖解法的優點。
  16. 7 ) based on the formulas of oblique section bearing capacity and normal section bearing capacity, the paper set rules to determine the failure mode of the wall and gave several main factors

    7 ）根據墻體斜截面抗剪極限承載力公式和正截面極限承載力公式，給出了墻體最終發生彎、剪破壞模式的判定，並提出了影響墻體最終破壞模式的主要因素。
  17. Additional research work on the behavior of shear characteristics had been carried out. though the tested beams had no stirrups, they possess fine mechanical properties and high shear capacity

    用本文第五章所建立的公式（ 5 . 27 ）計算rpc疊合梁斜截面抗剪強度，與試驗值較為吻合，用rpc材料本身抗剪安全可靠。
  18. The shear strength of the no corroded rc beams with stirrups is divided by two parts, that is the strength provided by the stirrups and the beams without web reinforcement. on the basis of this shearing mechanism of rc structural elements with web reinforcement, considering the confining effects of the stirrups, the shear carrying capacity expression of the corroded rc structural elements is given. the present results are compared with corresponding references and some reasonable conclusions are drawn

    對于銹蝕有腹筋梁的抗剪承載力問題，基於未銹蝕有腹筋梁抗剪強度公式建立的原理，即未銹蝕有腹筋梁的抗剪強度為相應未銹蝕無腹筋梁的抗剪強度和箍筋對梁抗剪強度貢獻兩部分的疊加，考慮箍筋的約束作用對斜截面抗剪強度的貢獻，建立了有腹筋構件斜截面抗剪承載力的計算表達式，且與相關文獻的結果進行了比較。
  19. Two types of the equivalent mode of concrete compression zone were discussed and the corresponding formulae to calculate normal section strength of unbonded prestressed composite beams with reaction powder concrete were given. the calculating results tend to be conservative

    結果表明，現有公式在計算rpc預應力疊合梁的斜截面開裂荷載及斜截面抗剪強度時，是偏於保守的。
  20. 2. based on the test results published over the word of steel fiber reinforced concrete beams without web reinforcements and with stirrups, the effects of steel fiber to shear resistance and the relationship of steel fiber to stirrups are analyzed, the improvements of steel fiber to failure states of reinforced concrete beams without web reinforcements are discussed. it is proposed that the formula of shear resistance of steel fiber reinforced concrete beams based on the model of the current design and construction spectification of steel fiber reinforced concrete structures ( cecs38 : 92 ), used of the uniaxial tensile strength of steel fiber reinforced concrete, and combined with different formulas specified in current design codes of concrete structures issued by different trades

    根據收集到的國內外對鋼筋鋼纖維混凝土無腹筋梁和鋼筋鋼纖維混凝土有腹筋梁的斜截面受力性能試驗研究成果，對鋼纖維在增強鋼筋混凝土無腹筋梁和有腹筋梁斜截面承載力方面的作用及其在箍筋抗剪承載力的關系進行了總結分析，對鋼纖維改善鋼筋混凝土梁破壞形態方面的作用進行了分析討論，提出了採用鋼纖維混凝土軸心抗拉強度指標，基於現行cecs38 ： 92 《鋼纖維混凝土結構設計與施工規程》計算模式、能夠與目前國內各行業現行混凝土結構設計規范中不同的鋼筋混凝土梁受剪承載力設計方法配套使用的鋼筋鋼纖維混凝土梁受剪承載力設計方法。
分享友人
分享到 Line

分享到臉書