斜端面 的英文怎麼說

中文拼音 [xiéduānmiàn]
斜端面 英文
angled end-face
  • 斜 : 形容詞（跟平面或直線既不平行也不垂直的） oblique; slanting; skew; bevel; diagonal; askew; inclined; tilted
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 端面 : end face; end plane; end surface; head face; side surface; terminal face
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. At the end of the corridor was the dressing room belonging to clarisse and simonne. it was a long, ill - built room under the roof with a garret ceiling and sloping walls

    克拉利瑟和西蒙娜的化妝室在走廊的一端，這間屋子狹長，造得很粗糙，在屋頂下面，墻角傾斜，墻上有裂縫。
  3. As one kind of key equipment in piping work of large - scale turbo - generator set in power plant, the machine is especially applicable to various welding bevels, flat end and angle of outer & inner diameter of ascending pipe, elbow pipe, bend, flange and etc., which greatly meets demands in pipe processing of construction site and manufacturers

    本機床是電站大型汽輪發電機組的管道施工的關鍵設備，對直管、彎管、彎頭、法蘭等管體的各種型式焊接坡口，端平面，內外徑過緩斜度及直口，能滿足施工現場和製造廠家對各種管件的加工要求。
  4. In order to considering the affections of the adjacent zone out of the girdler section, the internal - forces of two end surface which were obtained by the horizontal shaft system analysis are exerted on each model respectively. moreover, the weight, cable force and prestressing forces including girder longitudinal, diaphragm transverse and inclined web vertical directions are considered

    考慮到梁段以外附近區域的作用，在其兩端面上施加了由平面桿系結構分析所得的端面內力，另外，索力和預加力（梁縱向、橫隔梁橫向、斜腹板豎向）也施加在相應的位置，分析了箱形主梁在自重、索力和預應力作用下的空間應力效應。
  5. Grinding parts : including the ends, surface rings, trifle furrow, inclined plane, opening and etc

    研磨部位：包括端面周面斷屑槽溝斜面孔穴等加工研磨。
  6. There are some disadvantages on traditional construction method of the transition material 2b on upstream face of concrete face rockfill dam, i. e. overtopping, slope - cutting and incline compaction

    混凝土面板堆石壩上游坡面傳統的墊層料超填、削坡、斜坡碾壓的施工方法存在許多弊端。
  7. For meeting the related nantional standards and avoiding demolishment of the building, the underpinning and strengthening methods are used, with which the loads of center column are underpined by the diagonal steel strut and the cross - sectional areas of side pillar are strengthened, both ends of shear wall are chiseled in turn and then concrete is poured again

    通過採用斜向鋼支撐荷載轉移法實現對中柱的托換，採用剪力墻兩端分批鑿除后再澆搗實現對剪力墻的托換，採用增加截面法對邊柱進行加固，使建築物經托換和加固后能滿足國家有關規范的要求。
  8. This machine can also perform semi - grinding on simple - shaped irregular glass. when grinding peripheries, coarse grinding, refine gfindlag, and polishing are alternatively, hypofenuses, the angle of the grinder on the bowet - shape wheel can be obliquely adjusted to fit the ground angle for grinding

    磨削周邊時，可安裝三個磨輪進行粗精磨和拋光磨削斜邊時安裝碗形磨輪，將磨頭向後傾斜，調節斜面角度，以端面加工切削。
  9. According to the guidline, two nd : yag lasers have been designed and set up, one is end - pumped by lower output power ld using a selfoc micro lens, and the other is end - pumped by high output power ld using a pair of lenses are designed, and the characteristics such as output power and power stabilization of both solid - state lasers are investigated. thirdly, when an empty liquid crystal cell is inserted in the cavity of the nd : yag laser pumped by high power ld, the laser can operates in single axial mode. finally, according to the relationship between the laser output power and the longnitudinal a ld - end - pumped nd : yag laser sensor for displacement measurement has been investigated theoretically and demonstrated experimently, the results indicate that when the mean radius of pumping inside the laser cavity is far less than that of the oscilating laser mode, the exponential of the output power is a gauss function of the longitudinal positon of focused spot of ld pumping beam, both the measurement range and the sensitivity are dependent on the incident pumping power, as the incident pumping power is increased, the measurement range is enlarged and the sensitivity is improve d

    本文首先介紹了ld泵浦nd ： yag激光器的發展狀況、主要特性及其應用，從四能級速率方程出發，推導了ld泵浦nd ： yag激光器的閾值、輸出功率和斜效率的表達式，並簡述了激光器的工作原理、結構型式和倍頻方法；其次，以空間相關的速率方程為基礎，提出了ld端面泵浦nd ： yag激光器的設計方法，給出了一定泵浦耦合方式下，振蕩光模尺寸、最佳輸出耦合率、泵浦光模尺寸、泵浦光焦斑位置等參數的選取依據，以此為依據，設計了自聚焦透鏡耦合小功率ld泵浦nd ： yag激光器和透鏡組耦合高功率ld泵浦nd ： yag激光器，對激光器的輸出功率和功率穩定性等特性進行了實驗研究；再次，在帶尾纖輸出的高功率ld泵浦nd ： yag激光腔內插入一隻空液晶盒，觀察到了激光器以單縱模運轉；最後，根據泵浦光焦斑端面位置對激光輸出功率的影響規律，提出了ld端面泵浦nd ： yag激光位移傳感新方法，並進行了理論和實驗研究，研究結果表明：當激光晶體內泵浦光平均光斑半徑遠小於振西安理工大學碩士學位論文蕩光束腰半徑時，激光輸出功率的自然指數與泵浦光焦斑的縱向位置成高斯變化規律，測量范圍和靈敏度依賴于泵浦功率，隨著泵浦功率的增加，測量范圍擴大，靈敏度提高，當端面泵浦功率為7 . 24w （最大輸出功率為1 . 926w ）時，激光位移傳感器的測量范圍和靈敏度分別是13 . 045mm和0 . 148mw / pm 。
  10. 3. the trapping characteristics of ordinary helical gear pump are lucubrated by theory for the first time, the theoretic relation of the gear rotor between the end overlap coefficient and trapping phenomenon is discussed respectively with clearence or without clearcence, and the relation of trapping volume with the rotational angle turn is also discussed. the selective range of the helical angle that can eliminate completely the trapping of helical gear pump is gained, which never appeared in literature before

    首次對普通斜齒齒輪泵的困油特性進行深入的理論研究，分別討論了有側隙和無側隙時普通斜齒齒輪泵轉子的端面重合度與困油現象之間的理論關系，以及困油容積隨轉角的變化關系，得到了完全消除斜齒齒輪泵困油沖擊的螺旋角機械科學研究院博士學位論文的選擇范圍。
  11. The backward slant of the face of a golf club head, designed to drive the ball in a high arc

    球棍末端的后傾部分將高爾夫球棒棒頭的面向後傾斜，用於將球擊出一個高弧線
  12. The results show that the coupling efficiency is affected obviously by the fiber inclined angle, which can be improved if we choose the angle properly

    結果表明，不同的光纖斜端面角度下，對半導體激光器的耦合效率影響很大，根據不同的晶元參數合理選擇不同的斜端面光纖可以得到盡可能高的耦合效率。
  13. When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved

    分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。
  14. The outcome suggest that, firstly, the change of light transmission with the continuous change of parameters is periodic ; secondly, as far as the degree of effect is concerned, the light transmission of air - spaced prisms is much more sensitive to the change of the parameters than that of the glue spaced ones ; thirdly, as to the prisms glued with the same dielectric, the effect of prisms whose optical axis parallels to the glued layer is intense than those whose optical axis parallels to the plane determines by the normal of incident face and that of the cut face

    研究認為，激光偏光棱鏡的光強透射比隨各參量的連續變化都呈現出一定的周期性；各參量對空氣隙型偏光棱鏡的影響要比對膠合型棱鏡的影響大的多；同種介質膠合的棱鏡，各參量對光軸平行於切割斜面的設計類型比光軸平行於切割面的法線和入射端面的法線所組成的平面的設計類型的影響要大。
  15. The technical breakthroughs in growth of nd : cngg had been made. in particular, continuous laser operation was achieved from nd : cngg pumped by ld. when the crystal wafer was end - pumped by one bar of ld with 807nm wavelength, the cw laser output power of 123. 1 mw was obtained with slope efficiency of 22. 3 %

    本論文用自動化熔體提拉技術成功生長出< 111 >方向的直徑25mm以上，長度80mm以上的平界面無核心nd : cngg單晶，確定了晶體結構和物相，測量了晶體的光譜性能，晶體消光比達到34db ，晶體生長技術有新的突破，實現了連續激光運轉，用單支807nm半導體激光二極體端面泵浦該晶體片子，在國內首次獲得123 . 1mw的1 . 062 m連續激光輸出，斜效率達22 . 3 % 。
  16. Using field coupling theory, the coupling efficiency of ld at different fiber inclined surface is discussed, and experimental results are presented too

    摘要應用場耦合方法模擬計算了不同光纖斜端面角度下半導體激光器的耦合效率，並進行了實驗測量。
  17. Comparison and analysis of the stress distribute rule and deformation of two kinds of combination dies that with flat end plane or with oblique end plane cavity come to conclusion that the oblique end plane combination die is of higher intensity

    摘要通過對平、斜端面組合凹模在預緊及合成兩種狀態下應力和變形位移的對比分析，得出了斜端面組合凹模的應力分佈規律，指出在其他條件相同的情況下，斜端面組合凹模具有更高的強度。
  18. Slant - ended fiber

    端面傾斜光纖
  19. 5 through total - reflection theory and the inclination effect, we analyze the possibility of output angle 90o optical fiber

    5探討了光在光纖中的全反射條件和端面傾斜效應，從理論上分析了研製90o出光光纖的可行性。
  20. The theoretical model describing the output properties of double - cladding mof laser has been builded according to the mof ’ s extraordinary mode distribution

    光纖後端面直接輸出時獲得了最大11 . 6w的輸出功率，斜率效率達到了86 %以上。
分享友人
分享到 Line

分享到臉書