星傳動輪 的英文怎麼說
中文拼音 [xīngzhuàndònglún]
星傳動輪
英文
unit star driving wheel-
Strength analysis of two teeth difference cycloid gear drive
二齒差擺線針齒行星傳動擺線輪強度分析Basic terminology of cycloidal drives
擺線針輪行星傳動基本術語Design manual for enclosed epicyclic metric module gear drives
封閉行星米制模數齒輪傳動裝置匠設計手冊Tooth profiles and structural characteristic of ring gear of epicyclic drive with eccentric wheel and push rod
偏心輪推桿行星傳動內齒圈齒廓及其結構特性研究Study on control characteristic of synchronous point of a metal pushing belt - planetary gear continuously variable transmission system
行星齒輪無級變速傳動系統同步點振動控制研究3. three - dimensional modeling and mechanism simulation of planetary - gear transmission by means of i - deas software
3 .行星齒輪傳動裝置三維建模、裝配及動畫處理。These designing parameters include stiffness of epicyclical bearings, synthetic meshing stiffness of gears, stiffness of supporting bearing of out put shaft, mass of inner rack, meshing angle of gears, distance between inputting shaft and supporting shaft and input speed etc. according to these analyses, the possible way for improving the dynamic function of three - ring transmission may be put forward
這些設計參數包括：行星軸承剛度、齒輪綜合嚙合剛度、輸出軸支承軸承剛度、內齒板質量、齒輪嚙合角、輸入軸和支承軸間距及輸入轉速等，根據這些分析，可以提出改善三環傳動動態性能的可能途徑。Based on calculating and comparing with the transmission ratio, transmitting efficiency and power flow of the transmission plans in the controllable initation planet gear device referred in the literatures, the best reasonable solution was confirmed which can reduce the device dimensions and improve the transmission efficiency
摘要在對已有文獻提出的可控制起動行星齒輪減速裝置傳動方案從傳動比、傳動效率及功率流向等方面進行計算與比較的基礎上，確定了能夠使減速器裝置的整體尺寸小、外形美觀、傳動效率高的最合理方案。Accuracy of cycloidcl gear and pin wheel for cycloidcl drives
擺線針輪行星傳動.擺線齒輪和針輪.精度It can be regard as the theoretical basis to optimize the drive. according to the gear meshing theory, the meshing equations, the contact line equations and tooth profile equations are given. it gives a base for 3d modeling the drive
按照齒輪嚙合理論，推導出了滾錐齒超環面行星蝸桿傳動的接觸線方程、嚙合方程及各輪輪齒的齒面方程，為滾錐齒超環面行星蝸桿傳動的三維建模奠定了基礎。By means of the optimization method - punishing function method and taking the sum of the planet gear radius and center distance as the target function, the parameters of drive are optimized. by using the optimization program, the initial serial studies of drive are completed, the best serial parameter value of the drive is given
採用外點罰函數優化方法，通過取行星輪半徑和中心距之和作為優化目標函數，對滾錐齒超環面行星蝸桿傳動進行了參數優化，運用此優化程序，初步完成了對該種傳動的系列化研究，給出了傳動系列的最佳參數取值。The programme logic controller is utilized to control the inverter ' s output frequency which accomplishes controlling the velocity of speed - controlling asynchronous moter. the velocity between main asynchronous moter and speed - controlling asynchronous moter is composed by way of the differential planetary gear train, the tranmission system is made to regulate velocity stepless in large scope which succeed in controlling starting progress of load
使用可編程式控制制器對變頻器的輸出頻率進行控制，實現對調速電機轉速的控制。調速電機與主電機的轉速經差動行星輪系的速度合成，可使傳動系統在很大范圍內無級調速，實現對負載的可控起動。This paper mainly discussed the optimization design of two - stage star - type gear transmission system. it covered the two sides : one - stage gear transmission and two - stage gear transmission. on the basis of their analysis and research, the mathematic models are created which include the objective functions of minimum volume and minimum center distance, the constraints of contact strength, bend strength and scuffing strength
本文主要研究了航空發動機星型齒輪傳動系統的優化設計，對單級齒輪傳動和兩級星型傳動都進行了深入的分析和探討，分別以系統體積最小和中心距最小為目標函數，以齒輪的接觸強度、彎曲強度、膠合強度等為約束條件，建立了完整的數學模型。Design manual for enclosed epicylic gear drives
封閉行星齒輪傳動裝置的設計手冊Design of fuzzy reliability and optimization on planetary transmission
行星齒輪傳動的模糊優化設計The analysis result shows that the whole system could reach not only a static balance hut also a dynamic balance at all time because of the special phase angle relation, it keeps all the advantages of the traditional cycloidal - pin wheel planetary gear train
分析表明，由於四片環板採用了特殊的相位角關系，整個系統不僅能夠達到靜力平衡，而且能達到任意時刻的動平衡，同時又保留了擺線針輪行星傳動的優點，是一種具有發展前景的傳動形式。Cycloidal reducer is new kind of gearing machine which is based on the theory of planeary and cycloid pin geating
擺線針輪減速機是採用行星傳動原理及擺線針輪齒合新穎傳動機械。Double crank four ring - plate - type pin - cycloidal gear planetary drive driven by two motor is a new - type pin - cycloidal gear planetary that has practical value
摘要雙電機驅動雙曲柄四環板針擺行星傳動是一種具有實用價值的新型擺線針輪行星傳動。Therefore, it is necessary to study the load average performance of planetary gear transmission and the influence of load allocation between planetary gears
因此對行星傳動機構的均載性能及影響行星輪間載荷分配的因素進行分析有著重要的現實意義。Method of force bearing analysis and finite element analysis on contacting state of tooth surface for new typed fa planetary transmission of cycloidal needle - wheel
新型擺線針輪行星傳動受力分析方法與齒面接觸狀態有限元分析分享友人