時序邏輯控制 的英文怎麼說

中文拼音 [shíxùluókòngzhì]
時序邏輯控制 英文
sequential logic control
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 邏 : Ⅰ動1. （巡察） patrol 2. [書面語] （遮攔） blockⅡ名詞1. （巡察） patrol 2. [書面語] （山溪的邊緣） edge
  • 輯 : Ⅰ動詞（編輯; 輯錄） collect; compile; edit Ⅱ名詞（整套書籍、資料的各個部分） part; volume; division
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 時序 : [地質學] sequence; sequential; time sequence; timing sequence; sequence in time
  • 邏輯 : logic
  • 控制 : control; dominate; regulate; govern; manage; check; cybernate; manipulate; encraty; rule; rein; c...
  1. In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical

    在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。
  2. The subject has mainly finished designing and debugging software and hardware of a / d decode module, fpga video processing module, video data frame deposit module, base clock produce module, d / a encode module, i2c bus control module, etc. a / d decode module gathers analog tv signals and realize video decode ; fpga video processing module deals with the data after decoding and produces systematic logic control signal ; video data frame deposit module offers the buffering area to a large n umber of high - speed video data ; base clock produce module through input basic video signal offers system accurate relevant synchronous signal ; under control of video processing module d / a decode module convert digital video data into compound tv signal which can be shown in tv directly ; i2c bus control module is used to initialize the chip of system by simulating i * c bus timing

    本課題主要完成了a d解碼模塊、 fpga視頻處理模塊、視頻數據幀存模塊、基準時鐘產生模塊、 d a編碼模塊、 i ~ 2c總線控制模塊等部分軟、硬體設計及調試。其中a d解碼模塊採集模擬電視信號實現視頻解碼； fpga視頻處理模塊對解碼后的數據進行去噪處理的同時還負責系統的邏輯控制；視頻數據幀存模塊為大量高速的視頻數據提供緩沖區；基準時鐘產生模塊通過輸入基準視頻信號為系統提供精確的相關同步信號； d a編碼模塊在視頻處理模塊的控制下把數字視頻數據轉換成復合電視信號供顯示用： i ~ 2c總線控制模塊模擬i ~ 2c總線時序實現對系統中編、解碼晶元的初始化。
  3. The dcs of i / a series is regarded as main reference object, and the control is separated from model. and the configuration of control is operatised at administration system, not to be added into model, not to build control sound code also. therefore it realizes on - line adjusting, real - time control and so on. users configurate by filling table. they only define i / o condition, fill certain operation variable, and name logic variable. the software offers a friendly user ' s interface, so personnel can compile and modify the control and logic program, change the value of logic and control variable conveniently, attach themselves to run, debug and control the system, not need to know the programs deeply. so the configuration software offer a flat that control engineers can attend to control loop, not to give their attention to the complicated program

    在本課題中，採用填表的方式進行控制組態，用戶只需定義i / o條件、填寫具體的運算變量名即可。本軟體為建模人員提供了一個友好的用戶界面，使建模人員在建模時不必對模塊內部的控制、邏輯程序有很深的了解就可以方便的對其進行編寫和修改，實時改變各邏輯和控制變量在數據庫里的值，參與運行和調試，從而實現對系統的控制。因此，本組態軟體提供的這樣一個平臺，讓控制工程師能集中精力于控制迴路的構成，而不必拘泥於一些具體而煩瑣的程序操作。
  4. The thesis offers apd signal amplify circuit chart and controlling time - series logic circuit principle chart bearing practical applied value

    給出了apd信號放大電路和控制時序邏輯電路原理圖。
  5. It is easier for us to realize the hardwave circuit, and the content of sine wave at least by 45db is the projecting advantages

    本文主要論述一種實用的時序邏輯電路的設計與實現設計一個十字路口交通燈自動循環亮滅的控制器。
  6. The thesis analyses the problems on the noise of apd photoelectric receiving system. author designs apd laser signal receiving system circuits, front amplify circuit, controlling time - series logic circuits, dc / dc transform circuits. and takes apd bias voltage fuzzy control

    分析了apd光電接收系統的噪聲問題，並對apd激光信號接收系統電路、前置放大電路、控制時序邏輯電路、 dc / dc變換電路進行了設計，採取了apd偏壓模糊控制。
  7. It includes : dynamic show of technics flow, real time data acquirement and show, history data save and print, fault alarm, etc. the plc control system mainly accomplishes the wastewater technics flow control, harmonizes the logical relationship among local intelligent control instruments and transmits the state of each local equipment to the industrial computer simultaneously, the plc control station receives the control commands from the industrial computer ; the local intelligent units take charge of the correlated parameters measure, disposal and control, and it will transmit the related parameters to the computer, etc. in this thesis, introduced municipal wastewater treatment technics, the integrated application program development of computer, the design method of plc control station, the communication between plc control system and computer, and the network of wastewater treatment with profibus - dp was also discussed

    上位計算機主要實現遠程監測和管理功能，具體包括:工藝流程動態顯示、實時數據獲得及顯示、歷史數據存儲與列印、故障報警等功能plc控制系統主要完成工藝流程式控制制以及協調現場各智能儀表之間的邏輯關系，將現場各設備的運行狀態通過通訊網路傳輸到上位計算機，並接收上位計算機的控制指令;現場各智能儀表單元負責各相關參數的監測和處理、控制，並將有關參數送往上位監控計算機進行處理、保存等。本文以莎車污水處理項目為例，介紹了城市污水處理工藝、上位監控計算機的綜合應用程序開發、城市污水處理自動控制系統plc控制站的設計和採用profibus系列中廣泛應用於現場設備的profibus - dp總線。
  8. And, the thesis mainly presents the research on the key technique of the dataflow control, including the realization of the pci interface control, the control of the sram memory that read or written by fpga, the pretreatment and the output control of the image and the intercommunication between pc and fpga. and then, it presents the design and the realization of the pc application program. in the end, it presents the debugging stepps and the application of the system.

    本文的重點在於介紹高解析度實時圖像處理系統的fpga控制邏輯設計，主要研究了該數字圖像處理系統中影響系統實時處理速度的數據流控制技術，如pci介面控制、 fpga與外部ram的高速讀寫控制、圖像的採集預處理，圖像的輸出控制等，本文還介紹了高解析度實時圖像處理卡的上位機應用程序設計與實現，本文的最後介紹了系統的調試及應用。
  9. Therefore it comes true the on - line adjusting, real - time control and so on. it sames as real locale. the software of logic protect ( include electric logic ) and control includes some usual algebraic and operation model of thermal control and logic operation of logic protect. it adopts foxboro ' s dcs as a example, so we configuration via filling table, user only define i / o condition, fill certain operation variable, and name logic variable. the software offers a friendly user ' s interface, personnel can compile and modify the control and logic program, change the value of logic and control variable conveniently, attach themselves to run, debug and control the set, not need to know about the inside of the old programs deeply. so the configuration software offer a flat that control engineer can attend to the structure of control loop and logic protect ( include electric logic ), not but to handle complicated program

    它以foxboro的dcs控制系統為主要參考模式，採用填表的方式進行控制組態，用戶只需定義i / o條件、填寫具體的運算變量名、邏輯變量名即可。本軟體為建模人員提供了一個友好的用戶界面，使建模人員在建模時不必對模塊內部的控制、邏輯程序有很深的了解就可以方便的對其進行編寫和修改，實時改變各邏輯和控制變量在數據庫里的值，參與運行和調試，從而實現對機組的控制。因此，本組態軟體提供的這樣一個平臺，讓控制工程師能集中精力于控制迴路及邏輯保護（包含電氣邏輯）的構成，而不必拘泥於一些具體而煩瑣的程序操作。
  10. ( 3 ) design the fast calculation of modulus of 16 bit fix - point complex number and time logic of pulse compression system based on fpga ( ep1k100qc208 )

    （ 3 ）基於fpga （ ep1k100qc208 ）的16位定點復數的快速求模設計及系統時序和控制邏輯設計。
  11. With the development of science, embedded system has been widely used in the field of industrial control and intelligent appliance with increasing complication of control logic and function. as compared with the simple control logic program of the earlier embedded system, modern embedded system is inclient to integrated operation system, which makes embedded system more and more important

    隨著科學技術的不斷發展，嵌入式系統在工業控制和智能家電領域得到了廣泛的應用，同時控制邏輯和功能也變得越來越復雜，相對于早期嵌入式系統所採用的簡單的控制邏輯程序，現代嵌入式系統越來越傾向于使用完整的操作系統，這就使得嵌入式操作系統在嵌入式系統領域變得越來越重要。
  12. 4. complete the design of system ’ s logic function with fpga. the sdram ’ s controller and ping - pong operation is studied, and the data ’ s continuous storage is also realized. 5

    4 .設計實現系統的fpga邏輯部分，並研究了高速大容量sdram控制器和進行乒乓存儲操作邏輯時序，實現了數據流的連續傳輸。
  13. The broadband signal is generated by high speed d / a, and the logical control of the system such as the interface timing control of ide or sdram is implemented by fpgas

    採用高速d / a實現輸出信號的高寬帶，採用多片fpga完成整個系統的時序邏輯控制，比如ide介面時序的實現， sdram的操作等。
  14. The thesis emphasis the way and arithmetic of the key equipment of walking reheating furnace : loader machine, unloader machine, walking system, series transfer roll, control system of burning and tracking of steel billet, . make use of the system, we can carry out the function of transferring measuring and weighting, detecting, loading and unloading tracking the steel billet, we can control process of burning and exchange data each other to track the steel billet and manage the process over all of product line. goals of reheating furnace ' s producing process such as high yield, low consuming and pollution, automatic operating mode are achieved

    本文著重研究了步進式加熱爐關鍵設備如：裝鋼機、出鋼機、步進梁、爐前爐后輥道、燃燒控制、板坯物流跟蹤等控制對象的具體控制軟體流程、速度控制曲線、行程計算等具體控制策略和演算法，完成了攀鋼1450熱軋加熱爐基礎自動化系統（ l1 ）和熱工儀表的一級控制，實現板坯輸送、測量、裝出料、物流跟蹤、加熱爐燃燒控制以及板坯庫的數據信息交換，通過plc和二級計算機系統進行順序、定時、聯鎖與邏輯控制，實現了操作自動化與物料系統的全線跟蹤管理。
  15. In data sampling circuit, high - speed, complex programmable logic device cpld technique is used. high - speed double - port ram, control sampling time sequence logic, cpu interfaces and bus circuit are implemented in cpld. sampling speed is up to 80mhz, sampling depth is ik - byte, and cpld can fulfill the requirement of the software arithmetic to sampling

    在數據採集電路中採用了高速復雜可編程邏輯器件cpld技術，晶元內設計有高速雙埠ram 、控制采樣時序邏輯及cpu介面、總線等電路，采樣速率高達80mhz ，采樣深度1k位元組，很好地解決了超聲波微位移傳感器軟體演算法對采樣的要求，並可實現在線升級，大大提高了系統的整體性能。
  16. In the last part, signal quality is evaluated and pre - distortion calibration is applied to improve signal quality

    第三部分完成了信號源的系統控制，包括系統邏輯控制、介面邏輯、時序控制、地址計數等。
  17. The first is the interface of software and hardware which is based on opc technology, its function is building the communication between the devices and the function components ; the second is the control module which corresponds with all of the function components according to the task and process ; the third is fms configurable components module, it can provides not only the friendly operation environment but also the configurable operation interface in line with the layout of devices on the workshop. on this basis, a prototype system is developed, by which the control system of the flexible manufacturing system is constructed for the teaching fms system in the cims center of college

    基於opc技術的軟、硬體介面模塊，它實現了fms的各功能組件對底層設備的數據實時採集和控制指令的下達; fms調度控制模塊，它根據加工任務和加工路徑要求，協調並控制著fms系統各個功能組件之間的邏輯動作操作順序; fms系統組態配置模塊，它不僅提供了友好的人機操作界面環境，而且還可依據現場設備布局的具體情況進行界面的組態布局配置。
  18. Quite a lot of new ideas for designing both logic structure and scheduling structure of the open architecture cnc system have been implemented, including the principles of module - classification, large buffer mechanism for data transfer between modules, principles of time - allocation scheduling, and etc. based on the software structure, the author implemented a few function - modules, such as master - control, interface, decode, interpolation, position - control

    本文在系統的邏輯架構設計和時序架構設計方面做了不少創新性的工作：提出了開放式數控系統的模塊劃分原則，設計並實現了模塊間的大緩沖機制；提出了開放式數控系統的時序設計原則，提出了rtlinux環境中的數控系統時序實現機制並給出了具體方案。
  19. ( 3 ) based on principle analysis and simulation, the main parameters are obtained. and the hardware solution is proposed - parallel processing system with multiple dsp. ( 4 ) the design of the software used to control logic and timing is presented

    （ 4 ）在硬體設計的基礎上，提出了在本系統中實現時序和邏輯控制的軟體（不包括正交波束形成演算法的實現）設計方案（包括系統中斷系統的設計和系統的bootload設計） 。
  20. It uses omnivision ' s cmos digital color image sensor ov7620 sampling the object image, ti ' s tms320vc5409 dsp as main controller, icsi ' s high speed sdram ic42s16100 as data buffer, altera ' s flex10k series cpld designing sdram interface and time sequence logic

    採用了omnivision公司的cmos數字彩色攝像晶元0v7620采樣物體圖像， titms320vc5409dsp作為主控制器， icsi的高速sdramic42s16100為數據緩存， alteraflex10k系列cpld來設計sdram介面和時序邏輯。
分享友人
分享到 Line

分享到臉書