時間淬火 的英文怎麼說

中文拼音 [shíjiāncuìhuǒ]
時間淬火 英文
time quenching
  • 時 : shí］Ⅰ名1 （比較長的一段時間）time; times; days:當時at that time; in those days; 古時 ancient tim...
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 淬 : 動詞（淬火） temper by dipping in water, oil, etc. ; quench
  • 火 : fire
  • 時間 : time; hour; 北京時間十九點整19 hours beijing time; 上課時間school hours; 時間與空間 time and spac...
  1. Based on the analyses on mechanical properties, microstructure and fracture of - the microalloyed steels socrv with various heat treatment technique, it can be affirmed that various fractures arttribute to various mechanism, we can draw conclusion that the strength and toughness of microalloyed steels 50crv will be increase simultaneously by optimal heat treatment technique. to illustrate the mechanism of the strength and toughness of microalloyed steels socrv, we designed the comparative experiment and observed the microstructure of the sample which occurred at different quench and tempering temperature and different tempering time. the last experiment results were determined by the four factors : fined microalloyed elements grains, the decompound of martensite, martensite transformation of remnant austenite and the second phase precipitation

    為解釋微合金化50crv鋼強韌化機理，本文通過對不同淬火溫度，回火溫度，回火時間下的力學性能指標的對比及顯微分析，認為微合金元素的細化晶粒，馬氏體的回火分解，殘余奧氏體的轉變，第二相的沉澱析出共同決定了微合金鋼的強韌化情況，特別是由於微合金元素的存在，其細化晶粒及其碳氮化物的沉澱析出，導致鋼的良好的強韌性，並且如果工藝滿足第二相的沉澱析出強化大於回火馬氏體分解引起的軟化效應，會在硬度曲線中產生明顯的二次硬化現象。
  2. The duration of the quenching pulse should exceed the recovery time of the counter.

    淬火脈沖的持續時間應當超過計數器的恢復時間。
  3. The principle of multi - method and multi - parameter is suggested, which should be followed during characterizing microstructures of alloy steels by ultrasonic not method. ultrasonic velocity ( c, ) of transformation products through different heat processes of three steels was measured by high - accuracy ultrasonic installation. the velocity of quenched microstructure of 38crmoal is the lowest, which gradually increases with increasing tempering temperature between 200 ? and 650 ? after quenching process

    利用ti - 40n高精度超聲波測厚儀，研究了超聲波在不同鋼種、不同熱處理轉變產物中的超聲波速度c _ 1 : 38crmoal鋼淬火組織c _ 1最小，淬火后在200 650范圍內進行回火處理時，隨回火溫度的升高， c _ 1逐漸升高， hrc與c _ 1之間具有較好的相關性；正火組織的c _ 1介於淬火后中溫回火及高溫回火產物組織的c _ 1之間。
  4. From an examination of the tensile behavior of cz ly12 alloys under different temperature and strain rate, two kinds of deformation and intergranular fracture behaviors were observed that were opposite to the characteristic strain rate range in fine - grained superplasticity. the mechanisms are described as follows. the high ductility achieved at high strain rate is generally attributed to the dominant role of gbs accommodating mechanisms, which is considered as dislocation creep within grains controlled by subgrains

    研究選用自然時效淬火態的ly12鋁合金，進行了一系列不同溫度和應變速率下的單軸拉伸試驗， 480下，觀察到與傳統細晶超塑性特徵區間相反的行為：較高應變速率下，動態再結晶使晶粒細化，促進了晶界滑移，亞晶界控制的晶內位錯蠕變是晶界滑移的主要協調機制。
  5. Standard test method for quenching time of heat - treating fluids magnetic quenchometer method

    熱處理液體淬火時間的標準試驗方法
  6. Test method for quenching time of heat - treating fluids - magnetic quenchometer method

    熱處理液體淬火時間的試驗方法.磁性冷卻速度試驗器法
  7. Quenching and tempering were chosen to strengthen the material. the quenching temperature and time were adjusted based on the hardness measurement

    選擇淬火和回火作為本課題的熱處理工藝，並用硬度法確定可行的淬火溫度和保溫時間。
  8. Study of the calculating method of cooling time for interrupted quenching

    雙介質淬火冷卻時間計算方法的研究
  9. Due to the rapid heating rate, the time for wire stayed in high temperature zone is very short and no enough time for grain grows largely, hence the structure size of continuously induction heated wire is smaller than that of conventional heated wire and grain size is 2 to 4 level higher. due to the fine grain size, the induction heat oil tempered spring wire can acquire more reasonable comprehensive mechanical properties under same strength

    可見，由於加熱快，在高溫停留時間短，組織晶粒來不及長大，因此，連續感應加熱鋼絲的組織晶粒尺寸比一般加熱小，晶粒度高2 - 4級。由於組織晶粒尺寸細小，因此，感應加熱油淬火-回火鋼絲，在同樣強度下，具有更高的綜合b力學性能。
分享友人
分享到 Line

分享到臉書