曲柄軸 的英文怎麼說
中文拼音 [qūbǐngzhóu]
曲柄軸
英文
bent axle-
Crankshaft harmonic balancer
曲柄軸諧和平衡器Cycles. cotter pin and assembly of the axle cotter pin crank
自行車.扁銷和輪軸扁銷曲柄總成As the crankshaft rotates, the crankpin swings in a circle around the shaft.
隨著曲軸的轉動,曲柄銷繞主軸作圓周擺動。The cap and rod have bearings which permit the crankpin to rotate freely within the rod.
軸瓦蓋和連桿中有軸瓦,它允許連桿內的曲柄鎖自由地轉動。The load map and wearing maps of the crankshaft journals and crankpin are obtained under various operating conditions
研究表明:氣缸壓力和轉速升高后,曲柄銷和主軸頸的磨損均呈現增加趨勢。The crank is an offset section of the crankshaft.
曲柄是曲軸的偏置部分。It is composed of two components : level move and rotation. level move is realized by the co - operation of oil vat, handspike and synchronizer. rotation is realized by the brace and the triangle oriented axis
平行移動是由液壓油缸推動,通過推動軸承傳到推桿、同步盤,並相互配合實現的;旋轉運動是由曲柄、三角架導向軸完成的。It is applied to sorts of locomotive engine, in course of revolving of crank and connecting rod mechanism, there are revolving of the crankshaft, swinging of the connecting rod and reciprocating motion, so its motion state is complex, and periodic unbalanced force, by a few components, is great
曲柄連桿機構在高速運轉過程中,有曲軸的轉動、連桿的擺動及活塞的往復運動,其運動狀態復雜,各個部件所產生的周期性不平衡慣性力大,是引起發動機振動的主要原因。Crank bearing liner
曲柄軸承瓦The sampling rate of the system can reach 3704 sps, and the crank angle is 1. 94 degree per sampling point corresponding to the crank speed of 1200r / min. in the mean time, the position signal of the piston could be collected by photo - electricity switch
本研究首先設計和實現了摩擦力採集電子電路系統,裝置最大采樣率可達到3704sps ,在曲軸轉速為1200r / min時,對應曲柄轉角1 . 94度采樣點,並且可以採集用來確定活塞位置的光電開關的信號。It whips and mixes the fresh air and crankcase fumes as it rotates.
它旋轉時,把新鮮空氣和曲柄軸箱氣體攪混在一起。( 2 ) the crack compares with one depth with the first steps and the second steps natural frequency vibration, crack position near crank arm and main shaft transition round natural frequency little place under crankshaft ; with the third steps and the fourth steps natural frequency vibration, the smaller close to the second crank arm of crankshaft and round place natural frequency of the main shaft transition the position is
( 2 )裂紋同一深度比以第1階和第2階固有頻率振動,裂紋位置越靠近曲軸中間曲柄臂與主軸過渡圓處固有頻率越小;以第3階和第4階固有頻率振動,位置越靠近曲軸第二個曲柄臂與主軸過渡圓處固有頻率越小。Tile cutting disks, deep drawing tools, plain bearings, sealing and sliding sealing rings, guide gibs, liners and bushings, shaft protective sleeves, rolls for cold rolling mills, tools for diecasting pulverized materials, cutting disks
飾面花磚切削盤、深拉工具、滑動軸承、密封圈和滑動密封圈、導向槽、襯墊和軸套、曲柄軸套、冷壓磨碎機軋輥、硬模鑄造研磨材料的工具、刀盤。Crankshaft bearimg cover
曲柄軸軸承蓋Throw of crank shaft
曲軸曲柄曲柄半徑Double crank press
雙曲柄軸沖床Mainly used for crankshaft engine accessories grinding of automobile, motorcycle and ship
主要用於汽機車船之引擎配件曲柄軸研磨專用加工。Road vehicles - crankcase pressure measurement procedure using a pressure probe
道路車輛.使用壓力探測器的曲柄軸箱壓力測量程序The lower end of the connecting rod fits the crankshaft journal
在連桿大頭安裝曲柄軸頸。Bending of crank shaft
曲柄軸彎曲分享友人