最佳視距 的英文怎麼說
中文拼音 [zuìjiāshìjù]
最佳視距
英文
optimum viewing distance-
This is new horizons ' best image of ganymede, jupiter ' s largest moon, taken with the spacecraft ' s long range reconnaissance imager ( lorri ) camera at 10 : 01 universal time on february 27 from a range of 3. 5 million kilometers ( 2. 2 million miles )
這是「新視野」拍攝的木衛三? ?木星最大衛星的最佳圖片，這是飛船的遠距勘查成像器（ lorri ）於2月27日從350萬千米處拍攝的。By responding to changes in distance, you can maintain an almost constant ratio between texels in the impostor image - ideally this ratio would be 1 : 1
對距離變化的回應是，你可維持視點替用特效紋理的紋素之間的一個幾乎恆定的比率?比率的最佳理想值應該是1 : 1 。Because of radio wave propagating along the ducts with enhanced fields on the order of the free - space field, the problems of the co - channel interference are more complicate for communication systems with the results of intersystem interference and the formation of other system, and therefore affecting the determination of the coordination distances or the optimization of the distribution and separation of delay, and for surveillance system such as radar system the problems can be radar holes or the extensions of detect range
對于通信電路，它使系統間的相互干擾問題變得復雜，既可能幹擾其他系統又可能形成另外的系統，從而影響系統的有關參數如中繼電路的最佳組合（分佈、間隔）和協調距離，對于探測系統產生的則是雷達空洞、超視距探測等問題。這些問題對相關無線電系統特別是軍事應用系統可能是致命的，因而以波導傳播為代表的反常傳播特性研究受到極大重視。First, according to the demand of vimp for resin system, the reaction kinetics and rheological of up resin are investigated and the optimal content of low additive profile ( lpa ) is determined. then vimp based on a high - permeable medium and grooves are studied by visual experiments, through which the appropriate high - permeable mediums are selected and the parameters of width, depth and spacing for flow grooves and spacing for supply grooves are optimized. furthermore, various factors affecting the mold filling process are discussed and the whole vacuum infusion procedures are described taking examples of the manufacture of a model boat and a sandwich panel in one infusion
文中首先根據vimp對樹脂體系的要求，對vimp用不飽和聚酯樹脂體系的動力學和流變學性能進行了研究，確定了最佳低收縮添加劑的含量；對高滲透介質型和溝槽型vimp開展了實驗研究，通過可視化實驗優選出較好的高滲透介質，確定了引流槽的寬度、深度和槽間距及主槽的槽間距等工藝參數並進行了優化；對影響充模過程的各種因素進行了詳細的討論，並以模型船和夾芯面板的製作為實例描述了兩種vimp的成型過程；在實驗的基礎上，建立了二維滲漏模型，採用控制體有限元法對高滲透介質型vimp進行了成型過程的計算機模擬計算，通過充模時間和流動前峰的計算值與實驗結果的比較，驗證本文所採用的數學模型和數值方法的正確性，其結果對實際生產具有一定的理論指導意義。分享友人