有缺陷的保溫 的英文怎麼說
中文拼音 [yǒuquēxiàndebǎowēn]
有缺陷的保溫
英文
faulty insulation- 有 : 有副詞[書面語] (表示整數之外再加零數): 30 有 5 thirty-five; 10 有 5年 fifteen years
- 缺 : Ⅰ動詞1 (缺乏; 短少) be short of; lack 2 (殘缺) be missing; be incomplete 3 (該到而未到) be ...
- 陷 : Ⅰ名詞1 (陷阱) pitfall; trap2 (缺點) defect; deficiency Ⅱ動詞1 (掉進) get stuck or bogged do...
- 的 : 4次方是 The fourth power of 2 is direction
- 保 : Ⅰ動詞1 (保衛; 保護) defend; protect 2 (保持) keep; preserve; maintain in good condition 3 (...
- 溫 : Ⅰ形容詞(不冷不熱) warm; lukewarm; hot; gentle; mild Ⅱ名詞1 (溫度) temperature 2 (瘟) acute ...
- 缺陷 : defect; fault; faultiness; vitium; lesion; flaw; disorder; imperfection; drawback; blemish
-
The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is, the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin, it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed, too high negatire - pressure may enlarge the flaw in casting
結果表明:保溫塗料及一定的塗層厚度有利於提高鋁液的充型速度;澆注溫度越高、直澆道空心面積率越大,鋁液充型速度越快;模樣厚度太厚或太薄,均會使鋁液充型速度降低;一定的直澆道長度及直澆道面積有利於提高鋁液的充型速度;施加負壓會使鋁液的充型速度大大提高,但負壓過大會增大鑄造缺陷。At first, through the thermal analysis of chana sc6350 ac system, this paper clearly defines the main problems which need to be conquered emphatically. on the base, a series of test research on the optimizing disposition of the ac system has been done, and a large number of valuable data have been obtained, so that, the improving method of the ac system has been determined. in addition, the improving heat preservation measures have been researched comprehensively, by the ac environment imitating test, it was proved that these measures were very useful to strengthen the refrigerating effect and improve the riding comfort
本文首先通過對長安牌sc6350微型客車空調系統進行了有關的理論計算,找到了該車型空調系統存在的根本缺陷,明確了需重點解決的問題,在此基礎上,進行了一系列的空調系統優化配置的試驗研究,獲得了大量有用的數據,確定了該車型空調系統的改進方案。此外,對整車的保溫隔熱措施進行了全方位的改進研究,通過環境模擬試驗表明,這些改進措施對增強製冷降溫能力、改善乘坐舒適性具有明顯的效果。Liquid - hydrogen systems, which store the fuel at temperatures below - 253 degrees c, have been tested successfully but suffer from significant drawbacks : about one third of the energy available from the fuel is needed to keep the temperature low enough to preserve the element in a liquid state
以- 253貯氫的液態氫系統已測試成功,但卻有重大的缺陷:燃料所產生的能量中,約有1 / 3必須用來維持低溫,使氫得以保持液態。The measurement of dielectric loss and volume resistivity is effective preventive tests to judge insulating oil isolation status of polluted and aging, and it ' s important method of ensuring the safe operation of transformer and oil - filled circuit breaker, etc. however, the measuring systems of insulating oil dielectric loss and volume resistivity used at present exist the shortcoming of low accuracy, weak repeatability, inconvenience, and its thermostatic control system ca n ' t meet the challenge
絕緣油的介質損耗因數、體積電阻率測量,是判斷絕緣油的劣化與污染程度的有效預防性試驗,是保障變壓器、油斷路器等充油電力設備安全運行的重要手段。然而,目前所使用的絕緣油介質損耗因數、體積電阻率測試系統存在著測量精度低、測量結果重復性不好、控溫系統不能滿足控溫要求、操作不便等缺陷,針對這一現狀,本文對絕緣油介損及體積電阻率一體化測試系統進行了研究。Thin film sensors, produced by very modern manufacturing technology, have all advantages of the conventional bonded foil strain gauges, but without having their substantial disadvantages temperature drifts of the glue and creeping
該薄膜傳感器應用了非常現代化的生產技術,保留了傳統膠結金屬薄片應變測量的優點,並改進了一些固有的缺陷溫度誤差和蠕變。3. the gap defects in multilayer cvd sic coatings could be effectively controlled by means of slow deposition in low - pressure chemical vapor deposition ( lpcvd ). 2d c / sic composites with a multi - layer cvd sic coating prepared by slow lpcvd showed weight gain at 1300 @ in air condition
( 3 )採用慢速減壓化學氣相沉積工藝實現了對多層cvdsic塗層面缺陷的有效控制,實現了單一cvdsic塗層保護2dc sic在高溫下( 1300 )的氧化增重。分享友人