末端壓力 的英文怎麼說

中文拼音 [mòduānyālì]
末端壓力 英文
end pressure
  • 末 : Ⅰ名詞1 （東西的梢;盡頭） tip; terminal; end 2 （非根本、非重要的事物） nonessentials; minor detai...
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 壓 : 壓構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 末端 : end; terminus; terminatio; terminal; tail end; extremity末端棒 terminal bar; 末端朝上 endways
  1. The experiment apparatus has been developed, which is based on software ( labview ) and hardware ( pci board ni 6024e ). the displacements and generative force at the tip of the ipmc actuators were measured with respect to the different voltages, frequents and various waveforms which include square, sinusoidal, and triangular wave

    實驗選取了不同電壓幅值，不同頻率的方波、三角波、正弦波三種波形作為電激勵信號，利用高速攝像記錄ipmc的位移變形，並通過力傳感器實測了ipmc試樣末端的輸出力。
  2. Water pressure under 3 psi gently expand the folds of the colon wall to release entrapped fecal matter

    大腸水療法設備能夠維持一個規范和安全注射壓力，讓水清洗，以達到末端結腸
  3. Two crucial technologies in instantaneous negative pressure wave method are analyzed in this dissertation, then a means is presented which can eliminate the dynamic response time diversity between pressure sensors in the beginning and end of the pipeline, by adopting gps to unify the system time between data collecting systems in two ends

    分析了負壓波泄漏定位方法的兩項關鍵技術，提出了消除首末、端壓力傳感器動態響應時間差的方法，採用gps來統一首末端數據採集系統的系統時間；使定位更加準確。
  4. ( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )

    研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。
  5. Thermoplastics piping systems - non - end - load - bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings - test method for leaktightness under internal hydrostatic pressure whithout end thrust ; german version en 714 : 1994

    熱塑管道系統.壓力管道和模壓管件之間無末端承載的橡
  6. Prima experiments have been done in a swine trachea, and preesures and temperatures in the trachea end are measured dynamically during mechanical ventilation

    在豬氣管中進行了初步實驗，在機械通氣情況下監測了氣管末端的壓力和溫度參數。
  7. The new constant pressure controlle r for irrigation system is used to control the terminal pressure ( at the terminals of the branch pipes ), and it can more effectively convert the frequencies of the moters. thus energy can be saved

    新型的恆壓噴灌控制器採用的是末端控制（即分干管末端） ，這種控制方式可使噴頭獲得更好的噴水壓力，並且使電機可進行更有效的調速，從而獲得更好的節能效果。
  8. As the terminal of an electric network, the distribution network is directly connected with the users. it is charactered with wide spread line, low voltage level, many devices on the line

    配網作為電力網的末端，直接與用戶連接，線路分佈廣，電壓等級低，網上設備數量多。
分享友人
分享到 Line

分享到臉書