板料 的英文怎麼說

中文拼音 [bǎnliào]
板料 英文
panel veneer
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  1. When delivering boards. electric eye can scan cutting function to front segment and rear segment of middle and bottom board

    電眼裝置送板時來偵測，中板底板料之前段與後段作剪切的作用。
  2. Rolling stock. side planks and boards for standar - gauge line wagons and vans

    鐵路車輛.標準軌距鐵路貨車和箱式貨車的側面板條和板料
  3. You can find silk sheets in the linen closet. it ' s upstairs in the servants ' area

    你能發現絲綢板料在亞麻制壁櫥。它在樓上僕人區域。
  4. Abstract : shear force is interrelating with width and thickness of plate and obliquity of knife - edge

    文摘:斜刃剪切時，剪切力的大小與板料的寬度、厚度及斜刃傾角有關。
  5. The simulations of the blank forming process is always a very pop question in the domain of plasticity forming. it has very important significance as to making certain the figure of the blank roughcast calculating strain and stress, establishing reasonable forming craft and designing mold

    板料成形過程模擬一直是塑性成形領域研究的熱點問題，對于確定板料毛坯形狀、計算應力、應變分佈、制訂合理的成形工藝和模具設計有重要的意義。
  6. Technological design specification of bending for sheet metal

    金屬板料壓彎工藝設計規范
  7. This thesis briefly analyzes some yield criteria and instability criteria to the sheet metal forming first. then according to the transformation rule from ultimate strain to ultimate stress, it establishes the mathematical calculation models of the forming limit stress diagram for the software development according to hill48 、 hill79 and hosford yield criterion irrespectively

    本文首先分析了板料成形的屈服準則和失穩準則，然後根據極限應變到極限應力的轉換關系，分別採用hill48屈服準則、 hill79屈服準則和hosford屈服準則，建立了用於軟體開發的成形極限應力圖的數學計算模型。
  8. The product of electric furnace fittings including : micro - computer program temperature control instrument 、 refractory brick ( ultra - light weight energy saving brick ) 、 resistance wire 、 electroheat belts 、 electrical heat tube 、 silicon carbide rod 、 furnace bottom plate 、 muffle tank 、 vacuum sealed fan 、 wind wheel 、 axis 、 substructure 、 bin seat 、 flat shape plate 、 box 、 panel 、 weatherstrip plate 、 return air plate 、 bin 、 connection box 、 educe rod 、 thermocouple 、 thyristor 、 porcelain pipe 、 crucible 、 furnace chamber 、 furnace frame 、 charging bin 、 substructure 、 pit furnace cover lifter framework ( sole design ) and otherwise

    電爐配件產品包括：微電腦程序控溫儀、耐火磚（超輕質節能磚） 、電阻絲、電阻帶、電熱管、硅碳棒、爐底板、馬弗罐、真空密封風機、風葉、軸、底座、料筐座、扁形板、箱體、面板、擋風板、回風板、料筐、爐柵、接線盒、引出棒、熱電偶、可控硅、瓷管、坩堝、爐膛、爐門、爐框、裝料筐、底座、井式爐蓋升降機構（獨家設計）等。
  9. The thickness varies according to the half - apex angle, and the forming limit half - apex angle is the key which nc incremental sheet metal parts forming process succeeds, it relates to the material and thickness of the sheet metal

    變形區厚度的變化與成形半頂角有關，其中，成形極限半頂角是數控漸進成形能否成功的關鍵，它不僅與材料有關，而且與板料厚度有關。
  10. The predominant failure mode in stamping of sheet metal parts are wrinkling and fracture, in general, these defects may be eliminated by appropriate manipulated the blank holder forces

    摘要起皺和斷裂是板料成形過程的主要失效模式，合理控製成形過程中壓邊力，可以消除這些缺陷，提高成形性能。
  11. The springback angle increases with the increase of the punch round radius and clearances between the punch and the die while decreases with increase of the blank holder force, sheet thickness, friction coefficient and material hardening exponent

    回彈角隨凸模圓角半徑和凸凹模間隙的增大而增大，隨壓邊力、板料厚度、摩擦系數和材料硬化指數的增大而減小。
  12. From 60 ' s of the 20th century, the aluminum easy open can was putted into market, it was warmly welcome by the people as its too many advantages such as, light in weight, big in volume per unit, easy to open and carryover and long retention period etc. its usage and quantity are expanding from day to day

    鋁質易拉罐由於其質量輕、容重比大、便於開啟和攜帶、保質期長等優點，深受人們的歡迎，在飲料包裝容器中佔有很大比重。在易拉罐生產中最大限度地減少板料厚度，減輕單罐克重，提高材料利用率，降低生產成本，是制罐行業追求的目標。
  13. Building boards determination of formaldehyde emission - desicator method

    建築板料.甲醛輻射的測定.乾燥器法
  14. Simulation model of laser bending process has been established by dimension analysis with the control model of laser bending achieved based on regression of laboratory simulate data

    通過量綱分析建立了板料激光彎曲過程中彎曲角度的模擬模型，根據試驗數據對模型的相應參數進行回歸求解，獲得了該過程的控制模型。
  15. Jiangsu haian longteng nc machine tool co., ltd. concentrating on shearing to fold to press a profession number to control tool machine to develop, development and manufacturing produce, the main product has a liquid to press a put type to sheartrigger, liquid to press plank to anticipate to fold curved machine, various hydraulic presses machine, etc., is one of the business enterprise that the national machine isdustrial point production shears to fold tool machine

    海安龍騰數控機床有限公司，致力於剪折鍛壓行業數控機床的研製、開發和製造生產，主要產品有液壓擺式剪板機、液壓板料折彎機、開卷校平剪切生產線、卷板機，各型液壓機等，是國家機械工業重點生產剪折機床的企業之一。
  16. The main results show that : ( 1 ) the mechanism of laser bending is very different from that in bending with hard tools. ( 2 ) the bending angle is varied along scanning direction, and there is a deformation wave in the process. ( 3 ) the effects of sheet length on bending can be neglected while the length is more than 10 times of thickness. ( 4 ) the sheet width has much higher influence on the bending process

    分析發現：激光彎曲成形時板料的應力狀態與機械折彎時有根本不同；當激光束沿直線單向掃描時，板料兩端的彎曲角度不同；板料的長度大於10倍板厚或5倍光斑尺寸時，板長對彎曲角度的影響不再顯著；沿掃描方向，距離光斑中心3倍光斑尺寸以外的區域，仍然對彎曲變形量產生影響。
  17. Professionally produce q11 series, qc12y series beam shear ; wc67y series hydraulic press brake ; w11, w12 series tri - roller and four - roller machine ; j23, j21 series power presses ; w43 series board materials machine ; ( assembly line ) and cutting and shaping machine tools

    我公司專業生產q11系列、 qc12y系列剪板機； wc67y系列液壓折彎機； w11 、 w12系列三輥、四輥卷板機； j23 、 j21系列jh21系列壓力機； w43系列板料校平機（生產線）等剪切、成型機床的生產廠家。
  18. Carry the blanks and parts according to the request

    按要求搬運板料及零件。
  19. Wood - based panels ; determination of density ; german version en 323 : 1993

    木質板料.密度測定
  20. Wood - based panels ; determination of moisture content ; german version en 322 : 1993

    木質板料.含濕量測定
分享友人
分享到 Line

分享到臉書