梁的配筋 的英文怎麼說
中文拼音 [liángdepèijīn]
梁的配筋
英文
beam reinforcement-
On the base of codes in 1989, a series of seismic measures are improved in new codes, such as limit of inner - storey drift angle, minimum reinforced rate, column - beam moment magnification coefficient and moment magnification factor at the column base, etc
在89規范的基礎上，本次規范修訂進一步提高了包括層間位移角限值、最小配筋率、柱一梁級差系數等等在內的一系列抗震設計措施。Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed
在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete
通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。2 ) the structure elements should be laid out symmetrically and uniformly when designing steeve - arch structure, what ' s more, the reasonable selection of section geometric size near the arch foots of first beams is paid attention to and the arrangement difficulties of steel bar due to the big eccentric pressures 2, the analyses of anti - seismic features on transverse direction of the aqueduct l ) the method of adjusting the elements " mass can be harnessed in order to even the layout of seismic loads
2 ）設計吊桿式拱架支承結構時，各部分構件應當均勻對稱布置。另外，還應注意頭道梁拱腳附近截面的尺寸擬定，克服地震內力造成的大偏心受壓狀態給結構配筋設計增加的困難。 2 、橫槽向抗震性能分析1 ）可利用調整構件質量的方法，使得結構的某些構件的地震荷載分佈均勻一些。This product is mainly used for reinforcing various pre - stressed concrete structures such as large bridges, crane girders, cement power poles, pre - stressed concrete pipes, frames of multi - story factory buildings, etc
本品主要用於各種預應力混凝土結構的配筋。如大型橋梁、吊車梁、水泥電桿、預應力混凝土水泥管、多層廠房框架等。Thecalculating results show that the composite action between concrete floor and steel beamsgreatly influence the bending bearing capacity and initial rotational stiffness of joints, it shouldbe considered in practical engineer. reinforcement ratio of lengthways reinforcing bar andthe stiffener of web have great influencer on the behavior of connections, while the thicknessof end - plate and degree of shear connection have a litter influence on its behavior
分析計算結果表明:樓板與鋼梁的組合作用對節點的抗彎承載力及初始轉動剛度的影響非常大，實際工程中節點設計應當考慮這種組合作用;樓板內縱向鋼筋配筋率與柱腹板加勁肋對節點性能影響顯著，而連接端板厚度及剪力連接程度的影響則不是太顯著。The effects to beam for its normal section flexural capacity and rigidity and ductibility as well as other properties is discussed with different polypropylene fiber and different concrete strength by the bending test study herein on the reinforced concrete beams and the polypropylene fiber reinforced beams
本文通過對摻聚丙烯纖維砼配筋梁的試驗研究，分析討論了單筋矩形截面梁配筋率相同時，分別考慮聚丙烯纖維摻量和混凝土強度等級等因素對梁的正截面承載力、剛度及延性等幾個方面的影響。From above analysis, it is proved that, because the internal force distribution of cast - in - situ concrete hollow floor is notably different to that of waffle slabs, designed as grillage beams and reinforced by these results, the technical advantage of this structure may not be exerted sufficiently so that leading to the increase of reinforcement
通過以上分析證實，由於現澆空心樓蓋的與肋梁樓蓋具有顯著不同的內力分佈規律，現澆空心板按梁格進行計算並配筋，將不能充分發揮該結構的技術優勢，導致配筋量的增加。Not only the load is considered, but also the distance, the span, the wide and the percent of the reinforcement is considered. the chosen section is also meeted the stiffness
該公式不僅考慮到荷載大小、而且考慮了梁格的間距、跨度、梁寬、以及梁的配筋率等因素，且所選截面滿足剛度要求。It shows that the method suggested in the paper is simple, applicable for engineering and has good precision. on the bases of the formulas deduced, and combining with relative test datas, it studies in the paper several factors influencing the bearing performance of the simple beams, such as shape of the external tendons, the equal moment segment length, span - to - depth ratio of the beam, valid initial prestress of the external tendons, area of the internal tension reinforcement, strength of the concrete, vertical distance between
在公式推導的基礎上，結合相關試驗資料，研究了體外筋的形狀、等彎矩區長度、梁跨高比、有效張拉預應力、體內受拉筋配筋率、混凝土強度、錨固點到樑上邊緣在垂直方向上的距離、體外預應力筋水平段長度（雙折線型體外筋的情況）以及荷載類型等對體外預應力混凝土簡支梁受力性能的影響。The influences of different reinforcement style of the concealed bracings and different span - height ratio of lintel beams on bearing capacity, stiffness and deterioration process, ductility, hysteresity capacity, energy dissipation and failure features of coupled shear wall were studied through experiment of 7 specimens under low cyclic loading
通過7個結構試件在低周反復荷載作用下的試驗，研究了不同暗支撐配筋形式、不同連梁跨高比對雙肢剪力墻的承載力、剛度及其衰減過程、延性、滯回特性、耗能、破壞特徵等方面的影響。Thus it is necessary to study moment resistance, rotation stiffness and rotation capacity of the joints. in this paper, six specimens on end - plate composite beam - to - column joints and two specimens on end - plate composite beam - to - column joints were designed to subject to static load. the factors of m - characteristics about semi - rigid composite joints, including bolts, profiled steel sheeting, beam, column, stiffen rib and reinforcement, are studied
本文設計了6個端板型鋼-混凝土組合樑柱節點與2個端板型純鋼樑柱節點，通過對這些試件的靜力荷載試驗，重點研究了端板型鋼-混凝土組合節點的彎矩-轉角性能的影響因素，包括高強螺栓、壓型鋼板、型鋼梁、型鋼柱、加勁肋，以及混凝土板內縱向鋼筋配筋率等。Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。Tow speciments of prestressed fabricated beam - column subassembly were tested under reversed cyclic loading. experimental studies were carried out to investigate the strain distribution, failure mechanism and load - bearing capacity on the beam - column connections, as well as ductility, hysteresis curves energy dissipation, displacement restoring capacity of full pc speciments
本文通過兩榀預壓裝配式樑柱組合體在低周反復荷載下的試驗，了解了預壓裝配式框架梁端截面應變分佈、破壞機理和極限承載能力；探討了全預應力配筋截面延性特徵、滯回性能、耗能能力和變形恢復能力。Based on analysis and comparison of existing test data applied to existing ultimate strength prediction models, interfacial stress at the end of plate is deduced. after formulas for calculating the effective moment of inertia for frp - strengthened beams being revised and adjustment coefficient related to nominal main steel reinforcement ratio and curtailment length ratio being put forward, strength prediction formulas of compound beams under plate end debonding failure are established. in analysis of strength of compound beams under intermediate crack induced interfacial debonding failure mode, several bond strengths and their relation are introduced
對于板端剝離破壞，在總結現有承載力模型的基礎上，利用已有試驗數據對各承載力計算公式進行了分析比較，進一步採用分階段分析法，推導了板端界面應力的計算公式，在此基礎上，採用加固復合梁有效慣性矩的修正公式，建立了考慮名義配筋率和板端偏移比影響的板端剝離破壞梁承載力的計算公式；對于跨中受彎裂縫導致的粘結破壞，闡述了常見的幾種粘結強度之間的區別和聯系，並基於拉剪粘結強度，提出了跨中受彎裂縫導致粘結破壞的承載力計算公式，並利用現有試驗結果確定了模型中的一些參數；最後，利用試驗數據對本文建立的兩種粘結破壞承載力計算公式進行了檢驗，結果基本吻合。The main achievements of this thesis are as follows : l. the effect of the frp reinforcement ratio on cracking moment is analyzed. the calculating method and corresponding calculating formulas of flexural cracking moment of frp reinforced concrete beam are put forward
分析了纖維增強塑料筋配筋率對纖維增強塑料筋混凝土梁正截面開裂彎矩的影響，提出了纖維增強塑料筋混凝土梁正截面抗裂度的計算方法和相應的計算公式。Coupling beams " failure mode, shear distortion, ductility and energy dissipation were impacted by different shear - compression ratio from 0. 15 to 0. 20
是一種值得推薦的抗震聯肢墻小跨高比洞口連梁的配筋形式。Then the coupling beams with new reinforcement layout were made an inquiry into, and the improvement on the seismic behavior by coupling beams diagonally reinforced with a few rows in end regions was found out at last, based on the observations of the experimental phenomena and the analysis of the measurement result, and by the comparison of seismic behavior by making use of hysteretic response, ductility and energy dissipation behavior, a conclusion is presented : the code for design and construction of reinforced concrete high - rise structures ( the draft asked for advise hi 2000 ) ca n ' t ensure that the coupling beams have fairly good seismic ductility ; the result of improvement of the seismic ductility of the coupling beams by the increase hi stirrups besides the strengthen of longitudinal detailing reinforcement was n ' t obvious ; the coupling beams diagonally reinforced with a few rows in end regions have fairly good mechanisms, and the ductility and the behavior of energy dissipation are better than conventionally reinforced concrete coupling beams, so it is suitable to te tised in short coupling beams
本文通過對三根小跨高比（均為l h = 1 . 0 ）剪力墻洞口連系梁在低周反復荷載作用下的試驗，了解了嚴格按《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）設計的連梁具有的抗震性能，研究了採取增大連梁配箍量同時加強縱向構造筋的方案對抗震性能的影響，並進一步對新的配筋形式的連梁進行了探討，了解了在連梁梁端配置多排交叉斜筋方案對連梁抗震性能的改善。通過對試驗現象的觀察和量測結果的分析，利用荷載?位移滯回曲線、延性和耗能性能等指標對各個試件的抗震性能進行了比較，最後得出結論： 《鋼筋混凝土高層建築結構設計與施工規程》 （ 2000年徵求意見稿）不能保證小跨高比連梁具有較好的抗震延性：通過增大連梁配箍量同時加強縱向構造筋的方案對改善連梁的抗震延性的效果不太明顯；梁端配置多排交叉斜筋的連梁具有相對較好的受力性能，其延性和耗能性能等各項性能指標均優于普通配筋連梁，宜在深連梁中採用。2. the effect of frp reinforcement ratio on the ultimate moment of frp reinforced concrete beam is studied, the conclusion is that the ultimate moment increases with the increase of the reinforcement ratio for frp reinforced concrete beam in a certain range of reinforcement ratio
結果表明，對纖維增強塑料筋混凝土梁，在配筋率的一定范圍內，配筋率越大，受壓區面積越大，極限抗彎承載力越高。In this paper, there are three main purposes to be attained. firstly, enough ductility of coupling beams is needed, namely no shear failure occurs too early. secondly, the capacity of energy dissipation is satisfied on the grounds of enough stiffness
本文的主要研究目的是首先保證連梁具有足夠的延性，即保證連梁端部在達到較大彎矩之前，不過早發生剪切破壞；其次是在保證剪力墻整體強度的前提下，連梁還需具有良好的耗能性能；連梁的配筋構造不太復雜，方便施工。分享友人