梁的翹曲 的英文怎麼說
中文拼音 [liángdeqiáoqū]
梁的翹曲
英文
hogging of beam-
Simulation analysis of the lengthways warp of truck carling outside board
卡車縱梁外板縱向翹曲的模擬分析When analyzing skew support continuous curved box girder bridge, curved grid girder analyzing method considering warping effect is applied. matrix displacement method is applied in analyzing skew support continuous curved thin - walled box girder bridge with restrained bearing. in order to convert original rigidity equations to structural rigidi ty equations that can be solved, bearing nodal displacement matrix can be introduced, then unknown quantities at the edge of beams can be consistent with the restrained directions of skew bearings, unit rigidity matrix and unit nodal forces can be gained. structural rigidity matrix can be composed according to matrix displacement method, so nodal displacements and inner forces on the end of the rod that are unknown can be gained calculating equations of inner forces on any cross - section can be solved
分析斜支承連續曲線箱梁橋時，採用考慮翹曲作用的曲線格子梁分析方法，應用矩陣位移法對具有約束支承形式的斜支承連續曲線薄壁箱梁橋進行分析，考慮到支座的約束條件並不與梁端彎曲角位移和扭轉角位移的方向一致，引入支座節點坐標矩陣，使得梁端的位移未知量與斜支座約束方向一致，來計算單元剛度矩陣和單元節點力，然後按照矩陣位移法組集總剛並建立結構剛度方程，根據結構剛度方程即可求解未知的節點位移及桿端力，推導出任意截面處的內力計算公式。The major work is as follows : 1 ) based on dry hull modal analysis of flexure - torsion coupling vibration of unsymmetrical ship structures about longitudinal centerline, a transfer matrix method to calculate the dynamic characteristics is adopted after the parameters of structures are specified. taken both shear effect and warping deformations into account, the point and field transfer matrices are derived, and the influence on dynamic characteristics is computed according to different damaged positions and areas
其主要內容如下： 1 ）通過薄壁梁理論求得結構參數后，採用遷移矩陣法，在考慮剪切效應、轉動慣量和翹曲影響下，推導出求解破損船體結構的動態特性公式系統的場遷移矩陣和點遷移矩陣，並著重分析了船體不同破損程度和翹曲變形對船體振動的動態特性的影響。As the basis of stochastic torsional analysis, a stepped thin - walled beam model with complex cross - sections of arbitrary shapes ( open, closed or mixed ) is established in this paper, which takes into account the effect of secondary shear flow resulting from warping restraint
摘要具有復雜斷面形狀的階梯精密梁模型作為扭轉隨機分析的基礎，可以計及翹曲約束引起的二次剪流。Now, it is important to develop the composite blade researching, two measures including analysis methodology and finite methodology are provided. in this text, the finite rotation composite beam theory developed by hodges and his co - workers, during the late 1980 ' s, is adopted in order to research rotor of helicopter. a liner and two - dimension finite analytic measure is used to calculate the section characteristic and strain of the blade ; a semianalysis methodology is used to calculate the sensitive degree of section characteristic
以giavotto的線性二維有限元分析模型為基礎考慮了復合材料槳葉的結構和變形特點，計入了剖面翹曲的影響，在此基礎上編制了具有八節點等參元復合材料槳葉剖面剛度計算的有限元程序，分析計算了復合材料梁的剖面剛度、彎曲中心、剪切中心；並利用半解析法進行剖面剛度、剪切中心、彎曲中心的參數靈敏度分析。By an example, the warping theory of the thin - walled beam is compared with and distinguished from gbt, while the contribution and the defect of the former is presented
本文通過算例對廣義梁理論和薄壁桿件翹曲理論進行了比較研究，並指出了後者的貢獻和局限性。Based on the theory of thin - walled curved bar, reasonable hypothesized a third - ord parabolic curve, the paper adoptes variational method on energy, taking the coupled relationship of the effect of curvature radius, bend, torsion and shear - lag into consideration, establishes the elastic governing differential equation and boundary conditions for thin - walled curved box girders, which set the foundation of theoretical analysis of shear - lag effect in thin - walled curved box girders
摘要文章以薄壁曲桿理論為基礎，合理地假設了三個剪力滯翹曲位移函數，應用能量變分法推導出考慮曲率半徑影響、彎、扭、剪力滯耦合的曲線箱梁彈性控制微分方程及其邊界條件，為薄壁大麴率箱梁剪滯效應建立了理論分析基礎。分享友人