楔形分佈 的英文怎麼說
中文拼音 [xiēxíngfēnbù]
楔形分佈
英文
wedge shape distribution-
With the use of finite method we have developed computer simulation software for vacuum microtriodes with wedge - shaped and cone - shaped cathode on the basis of stduying deeply the field emission theory of vacuum microelectronics. the software included field section, grid point numbering, and the calculation of electric currents, transconductance and cathode capacitance, moreover, it can simulate the properties of vacuum microeletronic with variant structures and sizes. the relationship was studied and simulated among electic properties and device structures, sizes and cathode materials etc. the optimized design of vacuum microtiode was proposed
本文在深入研究真空微電子器件場致發射理論的基礎上，根據圓錐形、楔形陰極真空微電子三極體的不同特點，分別建立了物理和數學模型，在考慮空間電荷密度影響的前提下，以有限元法為基礎採用迭代的方法計算出真空微電子三極體內的電勢分佈情況，繪制出了等勢線、電子軌跡線，並得到了器件電學性能隨幾何參數的變化情況。The present study, ( d by using immunohistochemical single, double or triple staining method, showed the expression, relationship and distribution pattern of fos - protein, gfap or th in rat cns, investigated the plastic response and relationship of rat lumbar spinal cord as and neurons to pain induced by the unilateral tibia and fibula fracture ; ( 2 ) by using a double immuno - electron - microscopic method, investigated the ultrastructural characters of junction areas between neurons and as in the dorsal horn of rat lumbar spinal cord following the unilateral tibia and fibula fracture ; ? after intrathecal application of the carbenoxolone, a gap junction blocker, recorded the paw withdrawal thermal latency and compared with control
在腦干gfap - li星形膠質細胞主要分佈於mvz內的孤束核（ nts ） 、腹外側延髓（ vlm ）以第四軍醫大學博士學位論文及兩者之間的中間帶（ irt ）上。三叉神經脊束核尾側亞核（ vc ） 、外側楔柬核（ ecu ） 、藍斑（ lc ） 、臂旁外側核（ lp ） 、中縫大核（ rmg ） 、中腦導水管周圍灰質腹外側區（ vipag ） 、中縫背核（ dr ）等部位也出現一定數量的gfap陽性細胞。 f 。Firstly, the comparation study between the wedge pressing and the contour forging has shown that the transverse deforming initiated from the surface of the preforms. when the superficies reached the moulding wall, the deforming moved downwards as the high - direction deforming increased, till the moulding chamber was full of stock ; the transverse deforming of the moulding pressing stock initiated from the center of the stock then surned into a drum - type. the distribution of the density and hardness of the high - direction indicated that the wedge pressing acquired a better ability of pressing penetration
首先對比研究了楔形壓制工藝與模壓緻密化工藝，發現楔壓坯料的橫向變形從上表層開始，當上表面與模壁接觸后，隨著高向變形量的增加逐步向下移動，直至坯料充滿模腔;模壓坯料的橫向變形從坯料中間開始，形成鼓形。高向的密度、硬度分佈表明楔壓比模壓具有更好的壓透能力。The distribution of the gas - flow speed is measured at a position 1cm away from the outlet ( the end with larger air - gap ). it is illustrated that the gas - flow speed keeps increasing from the out surface of the inner sleeve to the inner surface of the outer sleeve, and then it decreases gradually
測量了楔形氣隙流體出口（大間隙埠）外1厘米處空氣流速大小的分佈，發現空氣流速自轉子（內筒）壁面處開始逐步增大，至定子（外筒）壁面處達到最大值，隨后開始減小。Conclusion it can be concluded that the not uniformly distributed occlusal force produced from the larger axial gradient degree, the defect of dentition, and the abrasion of teeth, may be the important factors which cause wedge - shaped teeth defect
結論研究結果說明，牙軸傾度增大、牙列不完整和牙齒磨損導致的（牙合）力異常分佈，可能是楔狀缺損形成和發展的主要因素。The theoretical model on reinforced earth retaining wall was given. 5. a lateral displacement analysis model about reinforced earth retaining wall that treats the wall ' s face panel as an elastic foundation beam has been presented
在楔體破壞的基礎上，探討了加筋土支擋結構的側向土壓力分佈規律，建立了一種加筋土支擋結構側向變形分析的理論模型。分享友人