極限尺寸 的英文怎麼說
中文拼音 [jíxiànchǐcùn]
極限尺寸
英文
dimension limit- 極 : i 名詞1 (頂點; 盡頭) the utmost point; extreme 2 (地球的南北兩端; 磁體的兩端; 電源或電器上電流...
- 限 : Ⅰ名詞(指定的范圍; 限度) limit; bounds Ⅱ動詞(指定范圍, 不許超過) set a limit; limit; restrict
- 尺 : 尺名詞[音樂] (中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」) a note of the scale in ...
- 寸 : Ⅰ量詞(長度單位) cun a unit of length (=1/3 decimetre)Ⅱ形容詞(極短或極小) very little; very ...
- 極限 : 1 (最高的限度) the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
-
Railway transport equipment. berne key operated sockets. dimension limits
鐵路通用器材.鍵控制的套筒.尺寸極限The corbel ' s dimension should be ascertained as the manipulative condition of diagonal section. the amount of longitudinal reinforcement be ascertained on the basis of the flexure model, is obtained according to static for balance condition, the calculative expression of the load is obtained. and in terms of the design method in ultimate state the maximum load
我國規范對于牛腿的設計規定,牛腿尺寸的確定以斜截面抗裂作為控制條件,縱筋用量的確定以彎壓破壞模型為基礎,根據靜力平衡條件得到承載力的計算公式,按照極限狀態設計方法計算得到,箍筋用量則按照構造要求確定。The load displacement curves and the ultimate strength of each member are presented. effects of beam length, radius of curvature and flexural - torsional rigidity on ultimate are considered
通過試驗研究,給出每個構件的荷載位移曲線和極限承載力,得到了曲梁承載力隨跨長、曲率半徑以及截面尺寸的變化規律。Mj threads - limit dimensions for bolts and nuts
Mj螺紋.螺栓和螺母的極限尺寸Upper limit size
最大極限尺寸Rounded trapezoidal threads ; limiting screw thread dimensions and allowances ; permissible deviations and permissible wear of thread gauges
倒圓角的梯形螺紋.第2部分:螺紋極限尺寸與公差.螺紋Round screw thread with clearance and steep flank with pitch 7 mm ; limiting dimensions of screw threads and allowances - permissible deviations and permissible wear of screw thread gauges
螺距為7mm的帶公差和斜側面的圓螺紋.螺紋的極限尺寸Edison thread for d - type fuses ; limit dimensions
D型熔斷器的圓螺紋.極限尺寸Construction drawings - indication of limit deviations iso 6284 : 1996
技術圖樣.建築圖樣.極限尺寸標注Unj threads - general requirements and limit dimensions
Unj螺紋.一般要求和極限尺寸Mj threads - limit dimensions for fittings for fluid systems
Mj螺紋.流體系統用的接頭的極限尺寸Aerospace. mj threads. part 3 : limit dimensions for fittings for fluid systems
航空航天. mj螺紋.第3部分:流體系統連接件極限尺寸Aerospace ; mj threads ; limit dimensions for bolts and nuts ; identical with iso 5855 - 2 : 1988
航空航天. mj螺紋.第2部分:螺栓和螺母的極限尺寸;等I aerospace - mj threads - part 3 : limit dimensions for fitting for fluid systems iso 5855 - 3 : 1988
航空航天. mj螺紋.第3部分:流體系統配件的極限尺寸Valves for vehicle tyres ; valve screw threads ; theoretical values, limiting dimensions of screw threads
機動車輪胎的氣門.氣門螺紋.理論值.螺紋極限尺寸Miniature screw threads. limits of sizes
小螺紋極限尺寸Iso - metric screw thread ; screw threads below 1 mm diameter ; limits
Iso米制螺紋.直徑小於1mm的螺紋.極限尺寸Maximum limit of size
最大極限尺寸Minimum limit of size
最小極限尺寸Iso general purpose metric screw threads - tolerances - limits of sizes for internal screw threads to mate with hot - dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
Iso普通米制螺紋.公差.第5部分:與鍍鋅前公差帶位置為h最大尺寸的熱浸鍍鋅外螺紋相匹配的內螺紋的極限尺寸分享友人