極限輸出功率 的英文怎麼說

中文拼音 [jíxiànshūchūgōnglǜ]
極限輸出功率 英文
ultimate output
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 輸 : Ⅰ動詞1 （運輸; 運送） transport; convey 2 [書面語] （捐獻） contribute money; donate 3 （失敗） l...
  • 功 : 名詞1 （功勞） exploit; merit; meritorious service [deed]: 戰功 military exploits; 立功 render me...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
  • 輸出 : 1 （從內部送到外部） export 2 [電學] output; outcome; outlet; out fan; fanout; 輸出變壓器 output ...
  1. In addition, it is shown that the scaling of output power is proportional to i ~ ( 2 ), when the current is less than the space charge - limit

    還研究了電流對輸出功率的影響，在電流達到空間電荷極限以前，微波輸出功率和電流的平方成正比。
  2. The radiation field evolves from a steady saturation state to a limit cycle oscillation state, and eventually to chaotic oscillation state as the current increases, the region in which the field exhibits limit cycle or chaotic oscillation is called the " soft " and " hard " nonlinear regime, respectively : ( 1 ) in the " soft " nonlinear regime, the radiation field is characterized by period doubled bifurcation and the discrete power spectrum

    隨著電流的增大，輻射場經歷由穩定飽和到極限環型的周期振蕩，並最終過渡到非周期性混沌振蕩的演化過程，按其狀態可分為「軟」和「硬」兩種非線性區域： （ 1 ）在「軟」非線性區域，場的極限環振蕩態和穩定飽和態是交替出現的，其特徵是典型的倍周期分岔，輸出功率譜是分立的。
  3. Usually, hpm devices working in the high current and large field amplitude state, after the field reaches saturation, the nonlinear effects will become extremely strong so that the intrinsic nonlinear phenomena ( for example limit cycle oscillation and chaotic behavior ) of the system occur. these nonlinear behaviors directly influence the output characteristic of the devices

    在通常情況下，高功率微波源器件都工作在大電流和強場工作狀態，尤其在場達到飽和以後，系統的非線性效應將變得非常明顯，非線性系統所特有的一些現象（如，極限環型振蕩和混沌行為）將出現，這些非線性現象直接影響器件的各種輸出特性。
  4. At first, modeling of these divvies by rate equations to obtain expressions for threshold and slope efficiency is given. on the case of this theory, the large numbers of literatures and datum are consulted, and the laser is home studied. through rationally selecting and improving the reflector surface, ensuring the beam quality, increasing farthest the absorption path, and improving effective pumping frequency ; through designing the water cooler of yag bar, the volume of laser is half the same internal and international production, and the output power is get to the extremum of the same international production

    並在此基礎上查閱了大量文獻和資料，對該種激光器進行了深入的研究，通過對yag棒直徑的合理選取併合理地改進反射鏡面，從而既保證了光束質量又最大限度的增加了吸收長度，有效的提高了泵浦效率；在不影響泵浦的前提下，通過有效縮短yag棒的長度減小輸出損耗；對yag棒的水冷系統進行優化結構設計，使激光器體積減小到國外同類產品體積的一半，而輸出功率已達到國外同類產品的極限值。
  5. In this paper, the mechanism and practical effect of existing coordinated control schemes are analyzed in detail, the advantage and drawback of the different coordinated control methods in practice are indicated clearly. this paper describes a fact that it is difficult to obtain rapid load response and stable main parameters at the same time by using the recent methods, underlines that heat release is the vital parameter that should be carefully controlled

    本篇在吸取了目前各種協調控制系統的優點的基礎上，提出了改進后的協調控制方案，主旨為以控制鍋爐的熱量釋放信號為核心，採用具有內在穩定特性的控制方案，充分加快機組的負荷響應速度，在機組所帶負荷已經接近當時的極限，及時限制輸出功率的增長，達到穩定機組的目的。
  6. We calculate the stress fracture limit, critical index limit and melting limit in a high power double clad fiber laser. the results show that the average output power decreases when the temperature is too high. to maintain the pumping efficiency and the output power, some cooling methods should be used when the output power reaches a certain level

    給出了熱效應對雙包層光纖激光器影響的裂解極限、臨界折射率極限和熔化極限與光纖結構參數和泵浦功率的表達式，理論分析和數值模擬結果表明對于高功率的雙包層光纖激光器溫度很高時激光增益下降，在一定的功率水平上需要進行外界的冷卻，以保證泵浦激光的效率和高功率的激光輸出。
  7. The choice of laser output window height is relation to many factors, such as pressure loading, thermal loading, yield stress, influence on wavefront, failure by fatigue. spherical windows can endure higher laser intensity. however, it brings some phaseshifts, which connect with laser windows parameters

    激光器輸出窗口厚度的選取與壓力載荷、熱載荷、材料極限強度、厚度對波前的影響、材料疲勞等多種因素有關，由於球殼窗口能承受較高的功率密度，但窗口本身帶來相移，該相移大小與窗口參數有關，根據位相均方根值選擇球殼窗口參數。
  8. However, the inherent shortcoming of piezoelectric transformer hinders its further development. the major problems include : ( 1 ) the development and design of the piezoelectric transformer involve in lots of theoretic aspects including the design of material, dimension, electrode and circuit ; ( 2 ) it is hard to harvest high voltage enhancement ratio and high - power output simultaneously ; ( 3 ) the operation of the piezoelectric transformer is strongly dependent on the resonance frequency, which leads to the difficulty in the design of driving circuit

    但其自身所存在的固有缺點也在很大程度上限制了壓電變壓器的進一步發展，突出的問題有:壓電變壓器的研製包括材料設計、尺寸設計、電極設計和電路設計等多個環節，所涉及的理論面很廣;壓電變壓器的高陞壓比和大功率輸出難以同時得到保證;壓電變壓器的工作過多地依賴于諧振頻率，為外部電路的設計帶來了困難。
分享友人
分享到 Line

分享到臉書