極限間隙 的英文怎麼說
中文拼音 [jíxiànjiānxì]
極限間隙
英文
clearance limit- 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
- 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
- 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
- 隙 : 名詞1 （縫隙; 裂縫） crack; chink; crevice 2 （空閑） gap; interval 3 （漏洞; 機會） loophole; op...
- 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
- 間隙 : （空隙） interval; gap; freedom; space; [機械工程] clearance; separation; stricture; clear; inter...
-
Taking the contact stress, bend stress stiffness and temperature stress as the condition, taking the weight of the kiln tyre as optimization aim function, the redia and the width of the tyre are optimized general optimize methods just consider the affecting of the parameters to aim function, but in fact, structural parameters ( such as structure dimension, interval and so on ), physics and dynamics ( damp factor, conduct factor, friction factor material ' s elastic module strength limits and so on ), which would be changed after used. the difference are called discrepancy robust design ' s basic concept is : all design parameters " discrepancy will affect the aim funct ion and arouse the quality target discrepancy
一般的優化方法，僅僅考慮了參數對其目標函數的影響，而實際情況下有些參數是變化的，產品的結構參數（如幾何尺寸、間隙等） 、物理和力學參數如阻尼系數、傳導系數、磨擦系數、材料的彈性模量和強度極限等的設計值與製造后和使用中的實際值會有差異，這種差異稱為設計變量和噪聲因素的變差。Linear induction motor is an important kind of machines which have some merits such as simple structure, low cost, durability, convenience for maintenance etc. the subject of this thesis is to study a big circular ring linear induction motor, and the major works in this thesis are summarized as follows : ( 1 ) considering the effects of the finite length of primary core, one - dimension analytical solution for the air gap field is cited in this paper. based on it, the single layer winding magnetic field is studied. considering whole - pitched and short - pitched winding configuration with odd poles and half - fulled slots in both ends, the double - layer winding magnetic field is analyzed, respectively
本文對大圓環直線感應電機進行了深入細致研究，內容包括： （ 1 ）本文採用有限長行波面電流作用於有限長鐵芯上的模型，引用了氣隙磁場一維解，研究了單層繞組磁場，奇數極半填槽雙層繞組在採用整距和短距時磁場的分析、比較，簡單介紹了二維解； （ 2 ）用有限元軟體ansoft對大圓環直線感應電機空載氣隙磁場進行了靜態分析，並分析了結果； （ 3 ）用軟體進行了額定電壓下的瞬態分析，得到了轉矩，位移，轉速隨時間變化曲線圖，利用單極性霍爾元件測定轉速並與軟體計算結果進行了比較，採用等效電路法計算了堵轉時的最大電磁力並做實驗進行了驗證，由實驗測得了三相電流波形，並與計算結果進行了比較，對其不對稱性進行了定性分析。
分享友人