極限檢查 的英文怎麼說

中文拼音 [jíxiànjiǎnzhā]
極限檢查 英文
limit checking
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 檢 : Ⅰ動詞1 （查） check up; inspect; examine 2 （約束; 檢點） restrain oneself; be careful in one s c...
  • 查 : 查名詞1. [植物學] （山查） hawthorn; haw2. （姓氏） a surname
  • 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
  • 檢查 : 1 （用心查看） check up; inspect; examine; censor; survey rummage; review; jerque; docimasia 2 （...
  1. The control commissions should not confine themselves to dealing with individual cases as they arise, but should work actively to find out how the party constitution, party discipline, communist ethics and state laws and decrees are being observed by party members

    黨的監察委員會應當不限於受理案件，而且要積極地檢查黨員遵守黨的章程、黨的紀律、共產主義道德和國家法律、法令的狀況。
  2. Sampling procedures for inspection by attributes - part 2 : sampling plans indexed by limiting quality for isolated lot inspection

    計數檢查用抽樣程序.第2部分:隔離批檢查用以極限質量為指標的抽樣方案
  3. The conclusion of reappearing analysis is that crane bridge be used as usual because main weld maximum stress of upper cover plate of main beam lower than yield limit though it higher than permissible stress. inner stress of secondary beam was over ultimate strength, and deforming is ultra big. so it was unfit for produce and secondary beam must be changed

    再現分析得出的主要結論為：橋架的主樑上蓋板主焊縫的最大應力超過了許用應力，但小於屈服極限，可以繼續投入使用；副梁內部的應力遠遠超過了強度極限，變形特別嚴重，不能滿足生產要求，因此更換新的副梁；端梁內部的應力超過了屈服極限，小於強度極限，在應力較大的位置焊接補強板；投入使用后，要對整個橋架進行定期檢查。
  4. The torture test choice will run a continuous self - test. this is great for testing machines for hardware problems

    極限檢測選項可以進行連續的自測.這對于排查硬體問題很重要
  5. The current information retrieval technologys just offer keywords - based searching, but ignore the semantic content of the keywords itself. they still have many limits and their capabilities need to be enhanced

    而現有的信息檢索技術卻存在很大的局限性，它僅提供了基於關鍵字的檢索，而忽略了關鍵字本身所含的語義內容，無法滿足用戶極具個性化的查詢需求。
  6. Traditional load test is generally accepted as a most directly and reliable method for determining the bearing capacity of piles. because the method need special reaction system, it will take more time and money and require high condition for test field. so it cannot be done randomly and widely, and cannot be done under hardly conditions

    傳統靜載試驗是公認的確定單樁承載力最直觀、最可靠的方法，但由於必需專門的反力系統，試驗費時、費力、費用高昂且對試驗場地有著極高的要求，也因此不可能做到隨機抽檢及大量普查；特別是在某些惡劣的條件下，由於空間的限制甚至不可能進行靜載試驗。
  7. Asymmetrical trapezoidal screw thread, artillery type, 3 degrees - 45 degrees. checking by limit gauges

    3和45角大炮型非對稱梯形螺紋用極限規檢查
  8. Extremeprogramming teams prefer to implement software to check for and detect errors, whether in the base software or in process, rather than to set up involved procedures which leave open the possibility of human error or laziness

    極限程序設計團隊不管是對于基本成型的軟體還是正在開發的軟體，喜歡以執行軟體來檢查、探測錯誤，而不是通過建立復雜的可能受人的錯誤和惰性影響的過程來做這件事。
分享友人
分享到 Line

分享到臉書