極高速加熱 的英文怎麼說

中文拼音 [jígāosùjiārè]
極高速加熱 英文
hypervelocity heating
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 高速 : （高速度） high speed; high velocity （hv）; high rate; swift; fast; express; high-speed
  1. In addition, in the austral winter, the westerly jet splits into two branches over the south pacific from 600 to 100hpa, with the subtropical branch located at 27. 5 s and the polar counterpart at 60 s. the maximal speed of the former is at 200hpa while the speed of the latter increases with height

    其次，在南半球冬季， 600 ? 100hpa的南太平洋上空西風急流會出現分裂，其中副熱帶急流中心位於27 . 5 s ，高緯度急流中心位於60 s ，前者在200hpa層風速達到極大值，後者風速隨高度增加而增加。
  2. However, the most commonly used x - ray sources didn " t change much no matter in structure or theory, still using thermionic cathodes as electron sources. such conventional x - ray tubes have some defaults, such as big volume, low frequency response, demanding for supply to cathode that was also brittle

    目前使用的x光源的基本特點是採用熱電子發射形式即採用熱燈絲作為電子發射源，在高壓加速下轟擊陽極產生x射線，這樣的光源體積較大，需要加熱陰極的電源，且對頻率響應慢。
  3. Quick - frozen food, cold food, products processing workshops and packaging, have relatively high health requirements, especially fresh food because ultimately no heating disinfection processes, production workshop microbial pollution is affecting the quality of products of the very important factors

    速凍食品、冷飲食品、肉蛋奶製品加工車間與包裝間，都有比較高的衛生要求，特別是生鮮食品由於最終沒有加熱消毒工序，生產車間的微生物污染是影響產品質量的極重要因素。
  4. The immersion electrical heater is chiefly applied in the direct contact mode of fluid heating. it features fast heat exchange and high thermal efficiency. it has the varieties of water heater, oil heater and gas heater. its heating element power density, i. e. the power per unit of heating area of the heating element, is an important parameter of the electrical heating element, which has a direct bearing on the performance and working life. the working out of the value is a highly specialized problem, being under the influence of many factors ( media flow rate, tempt, physical and chemical properties and direction in which the medium flows past the element etc )

    浸入式電加熱器主要用於直接對流體接觸加熱的場合，具有熱交換快，熱效率高等特點，分為水用加熱器、油用加熱器、氣體用加熱器，加熱元件的功率密度：即電加熱元件單位發熱面積上的功率，它是電加熱元件極重要的參數，直接影響加熱器的使用性能及使用壽命，它的取值是一個非常專業的問題，受到許多因素的影響（如介質的流速、溫度、物理和化學性質及介質流過加熱元件的方向等等） 。
  5. Engine operating conditions cold be changed quickly and are very bad sometimes, such as : from suddenly cranking to driving in winter, acceleration to sudden torque demand. in the light of zero emission vehicles, in order to achieve better hot efficiency, maximum power, higher safety and best emission, engine controls become more and more difficult. automotive engines are typical nonlinear, time - delay, time - varying parameter systems

    汽車發動機使用環境變化大，使用條件有時非常惡劣，從寒冷的冬天突然啟動進入行駛狀態，行駛過程中的突然加速，急劇的扭矩變化等等，在這樣的條件下，為了使其熱效率、輸出功率、行駛性、安全性和排氣清潔性處于最佳狀態，給汽車發動機的控制帶來了極大的困難，特別是零排放汽車排放標準的提出，對發動機控制提出了更高的要求。
  6. " the carbon dioxide from fossil fuels is distributed pretty evenly around the globe and not concentrated in the arctic, so it does n ' t look like we can blame greenhouse gases for the overwhelming bulk of the northern hemisphere warming over the past 27 years, " christy said

    然而，熱帶地區溫度在過去27年中僅僅升高了華氏0 . 3度。 「燃燒釋放的二氧化碳非常均勻地散布在全球，並非只集中在北極。所以過去27年間出現的北半球加速變暖的情況，好像並不能僅僅責怪溫室氣體。
  7. After studying the precision of fdm process, a rapid edm electrode fabrication technology based on fdm is developed, the technology, which combined pulse - reverse electroforming with strengthening of copper wire - arc spraying, can obtained compact crystal electrode ' s working part, and strengthened filling part which has big adhesion strength, better electricity and heat conductivity, the edm performance of the obtained electrode reaches that of electrolysis copper electrode

    繼fdm工藝精度研究后，開展了快速模具製造技術的研究，建立了基於fdm原型快速製造電加工電極的工藝。該工藝將脈沖電鑄和電弧噴塗紫銅背襯相結合，獲得了結晶緻密的電極工作層和結合強度高、導電與導熱性良好的電極背襯層，得到的電極達到了常規機加工紫銅電極的電加工性能。
分享友人
分享到 Line

分享到臉書