槳軸 的英文怎麼說

中文拼音 [jiǎngzhóu]
槳軸 英文
axis of screw motion
  • 槳 : 名詞1. （劃船用具） oar; paddle 2. （螺旋槳） propeller
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  1. Vertical axis or cycloidal, or vorth - schneider propeller

    垂軸螺槳，擺線螺槳
  2. Small craft with inboard engine - propeller shaft ends and bosses with 1 : 16taper

    舷內機小艇錐度為1 : 16的螺旋槳軸端和槳轂
  3. Small craft with inboard engine - propeller shaft ends and bosses with 1 : 10 taper

    舷內機小艇錐度為1 : 10的螺旋槳軸端和槳轂
  4. Different nacelle with deeper ross - section and intake over propeller shaft

    發動機艙、螺旋槳軸處的進氣口有一些不同。
  5. Power curve measurement and analysis for type of axial - flow stirrer

    一種高效節能型軸流式攪拌槳功率曲線測定及分析
  6. General specification of turboshaft and turboprop engines for aircraft

    飛行器渦輪軸和渦輪螺旋槳發動機通用規范
  7. Wj6 turboprop engine for medium transport aircraft ; wz8 series turboshaft engines for light helicopters ; hs6 series piston engines for small - sized transport and agricultural aircraft ; wj6g1 and wj6g4 series as turbines for industrial and marine application etc

    用作中型運輸機動力的渦槳6發動機，用作輕型直升機動力的渦軸8系列渦輪軸發動機，用作小型運輸機農用機動力的hs6系列產品，用作陸用海上的燃氣輪機動力渦槳6g1渦槳6g4系列產品等。
  8. Specification for propeller shaft ends and bosses for inboard - engined pleasure craft

    內列發動機船舶的螺旋漿軸端和螺旋槳轂規范
  9. Plain propeller shaft. assembly and nominal dimensions

    普通螺旋槳軸.組裝和標稱尺寸
  10. Experimental study on mixing performance of the twin - shaft paddle rotating mixer

    翻轉卸料式雙軸槳葉混合機混合性能試驗研究
  11. The axial flow type turbines are available for hydrauric power resources of medium and low heads. ganfa manufactures both the propeller type fixed blade type and the kaplan type adjustable blade type turbines. the propeller type turbines are suitable for hydropower stations with small or medium capacities and heads, and relatively stable loads. the kaplan turbines are suitable for hydropower stations with medium or large capacities and heads, and relatively unstable loads

    軸流式水輪機適應于開發中低水頭水力資源。我公司生產的軸流式水輪機按轉輪結構分為定槳zd轉槳zz兩種，定槳式一般適用於中小容量及水頭負荷變化較小的的水電站轉槳式多用於大中型電站及水頭負荷變化較大的水電站。
  12. Measuring clearance between propeller shaft & bearing

    螺旋槳軸與軸承間隙測量。
  13. Plain propeller shaft. interchangeability characteristics

    普通螺旋槳軸.互換性
  14. Shipbuilding. shaft lines. propeller - shaft - ends

    造船工業.軸線.螺旋槳軸端
  15. Shipbuilding. shaft lines. keys and keyways for tapers on propeller - shafts. diameters 100 mm to 680 mm. alternative

    造船工業.軸線.直徑為mm mm的螺旋槳軸上錐形體的鍵和鍵槽.可選擇的
  16. Applications of these bearing can be found in hydroelectric genrea - tors, of these bearings can be found in hydroelectric generators, vertical motors, propeller axie of vessels, tower cranes and squeezing presses

    該類軸承主要應用於水利發電機、力士發電機、船舶用螺旋槳軸、塔吊、擠壓機等。
  17. Propeller shaft revolution indicator

    螺槳軸轉速計
  18. A dynamic characteristic analysis of a propeller - rotor system

    槳軸發動機整機動力響應分析
  19. The carrier is capable of launching one aircraft every 20s. the nuclear - powered carrier has two general electric pressurized water reactors driving four turbines of 260, 000hp 194mw and four shafts. there are four emergency diesels of 10, 720hp

    尼米茲級航空母艦的動力來自兩部通用動力公司的壓水式核反應堆，由反應堆推動4個渦輪，從而產生26萬匹馬力合194兆瓦的動力來驅動4個槳軸，使航空母艦的速度可以超過30節。
  20. The control algorithms of both traditional and intelligent main - engine speed regulator are emphatically discussed in the thesis. the author established an simplified integrated mathematical model for marine main diesel engine, screw propeller and axis series with the mother type of large low speed diesel man b & w. the digital simulations for pi speed regulator are completed

    本文討論了主機速度控制的兩種實現方法；論文以實船應用的manb & w大型低速柴油機為母型，建立了柴油主機、螺旋槳、軸系一體化的簡化數學模型，並對常規柴油主機pi調速系統進行了數字模擬。
分享友人
分享到 Line

分享到臉書