樹脂塑性材料 的英文怎麼說
中文拼音 [shùzhīsùxìngcáiliào]
樹脂塑性材料
英文
resinous plastic material- 樹 : Ⅰ名詞1 (木本植物的通稱) tree 2 (姓氏) a surname Ⅱ動詞1 (種植; 栽培) plant; cultivate 2 (樹...
- 脂 : 名詞1. (動植物所含的油質) fat; grease; tallow 2. (胭脂) rouge 3. (姓氏) a surname
- 塑 : 動詞(塑造) model; mould
- 性 : Ⅰ名詞1 (性格) nature; character; disposition 2 (性能; 性質) property; quality 3 (性別) sex ...
- 材 : 名詞1 (木料) timber 2 (泛指可以直接製成成品的東西; 材料) material 3 (供寫作或參考的資料) ma...
- 料 : 名詞1 (材料; 原料) material; stuff 2 (喂牲口用的穀物) feed; fodder 3 (料器) glassware 4 (...
- 樹脂 : resin; jaffaite; peucine
- 材料 : 1. (原料) material 2. (資料) data; material 3. (適于做某種事的人才) makings; stuff
-
In this paper the situation and development of electronic packaging and its requirments for the encapsulate materials in high properties were introduced and a novel kind alicyclic epoxy for electronic packaging was also reviewed with 13 refs
摘要結合電子封裝的現狀、電子塑封材料的發展以及電子封裝對塑封材料提出的高性能要求,介紹了新型脂環族環氧樹脂及其作為塑封材料的應用前景,其包括耐熱型液體、含磷三官能團型、有機硅多官能團脂環族環氧樹脂。This test chooses general industrial vc / vac copolymer as raw material, various supplement material additives are also the common conventional avirulent additive on industry ; the plastic material processing routine is also the universal method to make the thermoplastic plate of low temperature of vc / vac copolymer that accords with medical requirement that its softening temperature is 55
本試驗選用氯醋共聚樹脂為主要原材料,所用輔料添加劑也是工業上常見的無毒性常規添加劑;採用常規的塑料加工成型方法及設備製造出軟化點為55的、符合醫用要求的低溫熱塑性氯醋共聚樹脂板材。Itaconic acid, also named “ methylene succinic acid ”, is important industrial raw material during the production of acrylic fiber, latex, synthetic resin, plastic, rubber, pharmaceutics surfactant, packing material of non - toxic food, herbicide, cleaning media, adhesive and plastic additive etc
衣康酸,又名「甲叉丁二酸」 ,是生產腈綸等纖維、膠乳,合成樹脂、塑料、橡膠、醫藥、表面活性劑、無毒食品包裝材料、除草劑、除垢劑、粘著劑及塑料助劑等的工業原料。Study on the mechanism of void formation in roto - moulding of long - fiber reinforced resin
長纖維增強液態反應性樹脂復合材料旋轉模塑成型工藝氣泡形成機理試驗分析Woodiness materials is prepared to thermoplastic through chemical modification, which can easy machining and has biodegradability ; is also composite with resin or plastic to wood - plastic ( wpc ) ; or dipping it into resin then sinter it to woodceramic
摘要木材經過化學改性可制備成易於加工且可生物降解的熱塑性木材;也可與樹脂或塑料進行復合得到木材塑料(木塑復合材料) ;或者將其浸漬入樹脂再進行炭化得到木材陶瓷。Fiber reinforced plastic rebar ( frp ) is a new composite, which is composed of fiber acting as reinforced material, synthetic resin acting as matrix, and some adequate auxiliaries, and is formed through a pultrusion process and necessary surface process. it has a high strength to weight ratio, excellent non - corrosive characteristic, fatigue - resistant characteristic, strong designability and magnetic neutrality, so it can be used in the applications with special performance requirements or where reinforcing bars are subjected to severe chemical attack
纖維增強塑料筋是以纖維為增強材料,以合成樹脂為基體材料,並摻入適量輔助劑,經拉擠成型技術和必要的表面處理所形成的一種新型復合材料,具有比強度高、耐腐蝕性能好、可設計性強、抗疲勞性能好、耐電磁等獨特優點。Aerospace series. non - metallic materials. resins, adhesives, reinforced plastics, preimpregnates. characterisation by liquid chromatography
航空航天系列.非金屬材料.樹脂粘接劑增強塑料預浸漬劑.用液相色譜法的特性說明Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application
熱、壓環境下壓阻變換壓力傳感器的性能可以通過有限元方法預測.這里研究了簡化的1 / 8模型,模型考慮了二氧化硅和氮化硅生成過程及堆陽極鍵合和膠粘結合過程.結果發現有限元預測結果和實驗數據具有可比性.範例研究表明,硼硅堆導致產生一定的非線性,但它隔離了硬環氧樹脂的非線性.在包裝過程中最好使用柔性環氧黏合或軟黏膠性結合.黏合材料的黏彈性和黏塑性將會導致傳感器輸出的滯后和漂移誤差.然而,在相對穩定的環境下,軟黏合劑對傳感器的影響可以忽略.此外,詳細的設計和過程信息有助於提高模型的適用性Study on optical reflector cf fabric peek thermoplastic composites
熱塑性樹脂基復合材料光學反射鏡研究Study on phenolic resin composite toughened by thermoplastic resin
熱塑性樹脂增韌酚醛樹脂基復合材料研究It can be mixed with thermoplastic trsiin to produce sound insulation material and sheet materials such as cushion, road covering sheet, water - proof layer for building s roof, etc
膠粉與熱塑性樹脂混合生產片材,如製作墊毯,道路鋪板,屋頂防水層和隔音材料等。This paper summarized the characteristics of continuous fiber reinforced thermoplastic matrix composite ( cfrtp ), the development of its raw materials, the existing preparation techniques at home and abroad and its application foreground in civil engineering field
摘要本文綜述了加固用連續纖維增強熱塑性樹脂基復合材料( cfrtp )預製片材的特點、原材料的發展情況、國內外現有的制備技術。An strippable antirust packing plastic which was hot - melt type and solvent type was made of eva resin as the main film components, corrosion inhibitor and modifying agents, and the application of the material in the antirust of cutting tool and machine tool were discussed
摘要介紹了以熱塑性樹脂為主要成膜物質,加入防銹劑和改性劑製成熱熔型和溶劑型可剝離防銹包裝材料,並敘述了其在刀具和機床防銹方面的應用情況。He product based on phenolic resin with fibre and mineral filler and other additives is processed into thermosetting plastics
本產品以酚醛樹脂為基材,加入纖維和礦物填料及其它助劑所製成的熱固性模塑料。He product based on phenolic resin with glassfibre and mineral filler and other additives is processed into thermosetting plastics
本產品以酚醛樹脂為基材,加入玻璃纖維和礦物填料及其它助劑所製成的熱固性模塑料。The product is a thermosetting molding compound, it is based on phenolic resin as a matrix and mixed with organic fiber and mineral filler and other additives
本產品是以酚醛樹脂為基材,加入有機纖維和礦物填料及其它助劑所製成的熱固性模塑料。Insulating materials - industrial, rigid, moulded, laminated tubes and rods of rectangular and hexagonal cross - section based on thermosetting resins for electrical purposes - definitions, designations and general requirements
絕緣材料.基於熱固樹脂材料的矩形和六角形截面的工業用剛性模塑的疊層管材和棒材.定義符號和名及一般要求The product based on phenolic resin with glassfibre and mineral filler and other additives is processed into thermosetting plastics
本產品以酚醛樹脂為基材,加入玻璃纖維和礦物填料及其它助劑所製成的熱固性模塑料。The product is a thermosetting molding compound, it is based on phenolic resin as a matrix and mixed with inorganic glass fiber, mineral filler and other additives
本產品以酚醛樹脂為基材,加入玻璃纖維和礦物填料及其它助劑所製成的熱固性模塑料。The product is a thermosetting molding compound, it is based on single stage phenolic resin as a matrix and mixed with organic fiber, mineral filler and other additives
本產品是以酚醛樹脂為基材,加入纖維素和礦物填料及其它助劑所製成的熱固性模塑料。適宜於注塑成型,工藝性能良好。分享友人