正方雙錐 的英文怎麼說

中文拼音 [zhēngfāngshuāngzhuī]
正方雙錐 英文
tetragonal bipyramid
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 方 : Ⅰ名詞1 （方形; 方體） square 2 [數學] （乘方） involution; power 3 （方向） direction 4 （方面） ...
  • 雙 : Ⅰ形容詞1 （兩個） two; twin; both; dual 2 （偶數的） even 3 （加倍的） double; twofold Ⅱ量詞（用...
  • 錐 : Ⅰ名詞1. （錐子） awl2. （似錐物） awl-shaped things 3. （錐體） cone Ⅱ動詞（鉆） drill; bore
  1. Analyse the klingelnberg amk855 gear milling machine. through analyse the transmission chain of the gear milling machine, analyse the transmitting principle and manufacture principle, introduce the two - - part cutter head, the process of formation of extended epicycloide and inaginary crown gear cutting principle ; overall introduce the formation of tooth face, deduce the calculation formulas of the main setting parameter of gear milling machine, and proving the correctness of the setting calculation formulas by the program of ‘ calculating of klingelnberg cyclo - palloid spiral bevel gear milling setting parameter ’

    通過剖析該機床的傳動鏈，分析了其運動原理和加工原理;介紹了雙層萬能刀盤、延伸外擺線的形成過程和假想平面產形輪切齒理論;全面介紹了齒面的形成方法，推導了銑齒機主要的調整參數的計算公式，並用「 klingelnberg擺線齒錐齒輪銑齒調整參數計算」的程序驗證了推導的公式的正確性。
  2. In order to solve the problems of which the spiral bevel gear of oerlikon type is necessary to out and modify repeatedly, a new method was developed to predict the contact pattern and greatly reduce the cost for manufacturing by means of building a tooth contact analysis model of prolate epicycloids bevel and hypoid gears for oerlikon skm2

    摘要為解決奧利康錐齒輪加工過程中需要反復試切、修正的問題，根據奧利康skm2機床建立了加工延伸外擺線齒錐齒輪和準雙曲面齒輪的齒面接觸分析模型，提出了一種可預測齒面接觸質量、降低設計加工成本的新方法。
  3. The directrixes of the in former two transmissions are the loxodrome and the geodesic on the pitch cones, that of the latter is an equal - pitch line along the direction of straight generatrixes in the hyperboloid surface, also is the vertical trajectory of the straight generatrixes

    前兩種傳動形式的準線分別為節錐面上的斜航線與測地線，後者的準線為單葉雙曲面上沿直母線方向的等螺距曲線，且為直母線族的正交軌線。
  4. ( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )

    研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。
  5. Ditetrigonal bipyramidal class

    復正方雙錐類
  6. Simultaneity it can generate the three - dimensional model of corresponding gear in a minute after by directly inputting gear parameters and the parameters of tooth form, which could prove th at the general tooth surface equation of double circular arc profile bevel gear obtained above was correct

    同時也可直接輸入齒輪參數和齒形參數，來生成相應齒輪的三維模型，從而證明了前面推導的雙圓弧弧齒錐齒輪通用齒面方程式的正確性。
分享友人
分享到 Line

分享到臉書