正負位移 的英文怎麼說

中文拼音 [zhēngfùwèiyí]
正負位移 英文
elevation suppression
  • 正 : 正名詞（正月） the first month of the lunar year; the first moon
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 位 : Ⅰ名詞1 （所在或所佔的地方） place; location 2 （職位; 地位） position; post; status 3 （特指皇帝...
  • 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
  1. There was marked and extremely marked linear positive relativity among condylar elastic - limit load, largest load, stiffness and bone density, in which all relative coefficients exceeded 0. 862

    其彈性極限負荷及位移、最大負荷及位移以正常組為最高，而剛度及骨礦含量則以切削組為最高，減徑組各項指標均最低。
  2. The temporal, spatial and frequency - field characteristics are discussed. the validity of the corresponding empiric formula is analyzed and the atmospheric effects and correction method are investigated in the data analysis of the ground - based observations. the atmospheric effects on the gravity observations are analyzed and detected using the gravity data recorded with the superconducting gravimeters at the global geodynamic project ( ggp ) stations

    利用實測地面氣溫、氣壓資料獲得大氣負荷效應時間序列的數值結果，研究大氣影響的時間、空間和頻率特徵，分析經驗公式的有效性，研究地面觀測和數據分析大氣影響和改正的方案；利用ggp臺站超導重力觀測資料，分析檢驗大氣重力影響；分析igs臺站大氣位移改正的可能性
  3. Finally, through the literature review and theoretical deduction, it is concluded that the implication of knowledge, physical distance and hierarchical distance are positively correlated to knowledge transfer cost while knowledge distance and trust arc negatively correlated to knowledge transfer cost

    最後，通過文獻分析及理論演繹得出知識隱含性、知識轉移雙方的物理距離或職位距離與知識轉移成本成正相關關系，而轉移雙方的知識距離、接收方對轉移方的信任則與知識轉移成本成負相關關系。
  4. 0 for an arithmetic right shift of an unsigned data type

    對正數進行數學右移位時，設置為0對負數據類型（
  5. Based on the response theory of an elastic earth to surface loads and the model of the standard atmosphere, the characteristics of changes in the loading effects with time, space and frequency are comprehensively investigated in this dissertation. the numerical results obtained in this study can provide accurate atmospheric correction models for high - precision continuous measurements of the geophysical fields such as gravity, tilt, displacement and strain on the earth ' s surface

    本文基於彈性地球對表面負荷的響應理論和標準大氣模型，綜合研究大氣負荷效應的時間、空間和頻率特徵，為地表重力、傾斜、位移和應變等物理場的高精度連續觀測提供精密大氣影響改正模型
  6. This paper analyses the type, function and characteristics of usual proportional control valves and raises a new modificative version in the light of their drawback. that is, basing on the principle of flow amplification and electrical feedback and throughout calculation and analysis on flow closed loop control and pressure flow combination., determination of the minimum controlled pressure difference as well as flow controlling range and structure of main valve and research of the dynamic and static characteristic, the paper puts forward control principle of " flow - load pressure change - displacement revision " and pressure / flow double closed loop, and further expounds that using a proportional controller and a electric mechanical transducer can separately serve the control function of pressure or flow as well as flow pressure combination

    本論文分析了目前常用比例閥的類型、功能、特性，並針對其不足提出新的改進方案，即：以流量放大，電反饋兩個原理為基礎，通過對流量閉環控制及壓力流量復合的計算分析、確定上最小控制壓差及流量控制范圍，確定主閥結構、功能特性研究等，提出了「流量? ?負載壓力變化? ?位移修正」的控制原理和壓力流量雙閉環控制原理，並進一步論述了利用一個比例控制器和一個「電?機械轉換器」就可完成獨立的壓力或流量控制功能以及流量壓力復合控制功能。
  7. When piezoelectric material is put on outside force, it will cause the translocation of positive and negative electricity inside piezoelectric material. then piezoelectric material will generate polarization and shape tied electricity on the surface of the piezoelectric material that is proportional to the outside force

    對壓電材料施加外力時，會引起壓電材料內部的正、負電荷發生位移，並產生極化，從而在壓電材料的表面形成與外力成比例的束縛電荷，稱為正壓電效應。
  8. In case of the longitudinal and lateral centerlines of the figure of the loaded car are asymmetric when freights are normally loaded, and considering the allowed shift in the longitudinal and lateral direction, the weight value and position of balances are deduced and an example is given

    摘要貨物正常裝載時，外形輪廓關于負重車縱、橫中心線都不對稱的情況下，考慮到貨物的縱、橫向偏移，對配重物的重量及位置進行了推導，並舉了實例。
分享友人
分享到 Line

分享到臉書