比熱阻 的英文怎麼說

中文拼音 [bǐrèzǔ]
比熱阻 英文
specific thermal resistance
  • 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
  • 阻 : 動詞（阻擋; 阻礙） block; hinder; impede; obstruct
  1. Abstract : apply computer simulation to the distribution pattern of air - flow without considering the cold condition of the combustion and compare the flow patterns under different designed circumstances. and the effect of the design of the partition in the air way of the burner on the flow and mixture of gas and air is especially studied. the result shows that the design of partition plays a very important role in strengthening the mixture of gas and air, but increases the loss of the resistance in the air way and the total pressure of the air way in same working conditions needs increasing

    文摘:應用計算機模擬的方法，在不考慮燃燒的冷態情況下，研究了熱風爐燃燒室內的氣流分佈規律.在此基礎上，比較了2種不同設計方案的氣流流動特徵，尤其是研究了燃燒器空氣通道內阻流板的設置與否對空氣和煤氣的流動和混合的影響.結果表明，阻流板的設計對加強空氣和煤氣的混合有著極為重要的作用，同時也增加了空氣管道的阻力損失，在同樣的工況條件下需要提高管道系統的總壓力
  2. Phenolic foam is a new generation heat preservation prevent fire soundproof material and polystyrene together ammonia ester foaming rubber etc, material to compare, and it is good that its biggest characteristics is a heat - proofound the low temperature contractility is smatt, and have te special prevent burning wit the size stability under 2000 heat, not burning, not melt not contract constant form not poisonous spirit hove no thick smoke, just surface formation layer

    信息內容：酚醛泡沫為新一代保溫防火隔音材料與聚苯乙烯聚氨脂發泡橡膠比，其最大特點是耐熱性好，低溫收縮性小，具有獨特的阻燃和尺寸穩定性，在焊槍火焰下，不燃燒不收縮不變形，無毒氣無濃煙，只是表面炭化，性質穩定，耐化學腐蝕抗老化。
  3. We adopt new production process of cold ends, so our sic heating elements have excellent specific rate of heat zone resistance and cold end resistance, saving energy, long life, avoiding over - temperature of cold ends to damage the furnace body. the commercial name of our sic heating elements is songshan silca heating elements

    我們的碳化硅電熱元件採用新的冷端部生產工藝，具有優良的熱冷端電阻比，節能、壽命長，同時避免了因冷端部溫度過高對爐體造成的損害。
  4. The two sunspots of a pair have different polarities, one would be a magnetic north and the other is a magnetic south. thus, we believe that there are magnetic field lines joining the two sunspots of a pair. the strong magnetic field locks the gas of the photosphere in places and inhibits the hotter gas below to rise at the sunspots

    黑子經常成雙成對出現，每對皆由極性相反的黑子組成，若一個為磁北，另一個必為磁南，由此我們估計每對黑子皆由磁力線所連系，強大的磁場牽制著光球層上的氣體，並阻止了下層較熾熱的氣體上升至黑子范圍，結果黑子比太陽表面其他地方溫度較低。
  5. Using the advanced technology by its head office ( newkey co., ltd. ), it produces various kinds of alumina black and white ceramic products. the component alumina ceramics, which are widely used in electron components, devices, electrical products, enjoy low loss of high frequency, high insulating strength, good specific volume resistance, small dielectric constant, high mechanical intensity and excellent airtightness and thermal and chemical stability

    本公司根據目前市場需求，生產出各種型號的黑、白陶瓷產品，廣泛應用於電子、電工、化學工業、紡織工業、水暖、宇航、環保等諸多方面，系列產品有高頻損耗少，比體積電阻大，介電常數小，強度高，氣密性、熱穩定性、化學穩定性好等特點。
  6. They have unique structure, morphology as well as mechanical, thermal and gas / liquid barrier properties than their conventional counterparts

    與傳統的復合材料相比，納米復合材料不僅結構和形態獨特，而且具有出色的機械、耐熱和阻隔性能。
  7. The interior size and the calorific capacity of the borehole are much smaller, moreover the temperature change is slow, so usually we can neglect the influence of calorific capacity but to consider according to the heat transfer in steady state process, thus we can establish one - dimensional and the two - dimensional thermal resistance model in the borehole

    而在鉆孔內部，包括回填材料，管壁和管內傳熱介質，與鉆孔外的傳熱過程相比較，由於其幾何尺寸和熱容量要小得多，而且溫度變化較為緩慢，因此通常可以忽略其熱容量的影響而按穩態傳熱過程來考慮，建立了鉆孔內的一維和二維的熱阻模型。
  8. 3. on boiler retrofit, the calculation of fuel burning, the heat calculation of boiler inside structure and convection section, and the design of structure parameter of feed water heat exchanger are made. the flue gas channels " resistance calculation and the boiler strength verifying are also carried out. replacement of water cooling wall improves heat exchanging and decreases loss of heat radiant

    對鍋爐本體進行了燃料燃燒計算、爐膛結構熱力計算、對流受熱面結構熱力計算、鍋爐給水加熱器結構參數設計、煙道阻力計算及鍋爐元件強度校核等；改進了水冷壁布置使換熱效果更好，減少輻射換熱損失；改進對流段結構，更充分的利用爐膛出口煙氣余熱，提高熱效率；並且進行了煙氣阻力計算、熱效率計算和能量平衡測試，對改進后的稠油燃料和改進前進行了對比，燃燒狀況和熱效率有明顯改善。
  9. The blade inner channel cooling is a complex convection - conduction coupling problem. this thesis build a three - dimension. compressible turbulence model, and give a general solve method. with the geometrical model of the glossily rectangle straight channel, the rectangle straight channel with in - line arrays disturb plates, the rectangle straight channel with staggered arrays disturb plates, the rectangle straight channel with slant disturb plates, this thesis compute the flow and heat transfer condition when the cold air path though these channels, and gain the temperature field, pressure field, velocity filed, in addition. this thesis also analyze the influence of the different channel height, the different channel materials, the different channels, and gain the function relation between he nusselt number, friction factor and reynolds number. this thesis is emphasis on the new heat transfer enhancement structure, that is, disturb plates, with the comparison with the glossily channel and channel with pin fins, the heat transfer enhancement effect of the former is better, and the conclusion can be used in the design of aircraft blade

    葉片內部通道冷卻是一個復雜的對流?導熱耦合傳熱問題，本文在分析葉片內部通道冷卻的流動與傳熱情況的基礎上，建立了三維、可壓縮紊流的物理模型，得到了通用的求解辦法；利用不帶擾流片的矩形直通道、帶順排擾流片矩形直通道、帶叉排擾流片、帶傾斜擾流片的矩形直通道的幾何模型，計算了冷卻空氣通過這幾種通道時的流動與換熱情況，得到了各種不同情況下計算區域的溫度場、壓力場、速度場；在此基礎上分析了不同的通道高度、不同的葉片通道材質對葉片內部通道冷卻的影響，並整理得到了各種通道形式下，努謝爾數和阻力因子與雷諾數的函數關系；本文重點研究了新型的葉片內部通道冷卻強化傳熱措施?帶擾流片的內部冷卻通道的強化傳熱效果，通過與光滑矩形直通道、帶針肋通道的冷卻效果的比較，表明了這種新型鮚構的優勢，對于葉片內部通道冷卻結構的設計可以起到指導的作用。
  10. By analyses and compares, the conclusion is that it would be better to choose high resistance grounding of distribution transformer for hydro turbine in hydro power station. there is no certain conclusion for steam turbine in fossil - fired power plant. getting a clear answer to choose good generator grounding mode still needs practice and time

    經分析比較認為，在水電站水輪發電機組宜選用接地變高阻接地方式；在火電廠和熱電廠汽輪發電機組，選用何種接地方式，給出明確的結論尚需理論和實踐的進一步深入。
  11. The heat - exchange apparatus is the window for air - conditioner to exchange energy with outside. we analyze the efficiency of heat - exchange apparatus by the theory of heat - transmit, and compare the advantage and disadvantage of different type evaporator ' s and condenser ' s design by lots testing, and compare the effect of heat - exchange for different type flake, and compare the effect of heat resistance for different stretch of copper tube and flake. then we get many useful results from those different comparing

    蒸發器與冷凝器統稱為換熱器，換熱器是空調器與外界進行能量交換窗口，利用傳熱學原理對換熱器的效率進行分析，通過大量的試驗比較不同的蒸發器，冷凝器設計方案的優劣；比較冷凝器使用不同片型對換熱效果的影響；比較銅管與翅片的不同脹緊對熱阻的影響，通過比較得出很多有用的結論。
  12. Using the dynamic mechanical analyzer ( dma ), pdms / pma ipn was investigated at temperature of 5 - 180 c. the initiator, the component ratio, the type of pdms and the filler effected the damping properties. the result showed that the damping ability varied with the parameter and there was an optimal value. the excellent damping material in the papers was ipn, where tan man was 0. 735, and the damping functional temperature ranged with tan 8 > 0. 3 was 46 c. the micro - morphology and structure of pdms / pma ipn were characterized by two kinds of sem

    高分子阻尼材料的有效阻尼功能區是在ipn材料的t _ g區間內，而研究常溫條件下的阻尼性能更具有重要應用價值，運用動態熱機械分析（ dma ）儀對ipn阻尼材料進行表徵，在5 180內對其損耗因子（ tan ）進行研究，發現引發劑和交聯劑的用量、聚硅氧烷的用量和分子量等參數對ipn阻尼性能的影響較大，存在一個合理配比值，當pma與粘度為3300pa ? s的pdms之比（質量比）為1 . 17 ： 1 、交聯劑用量為1時， tan最大值為0 . 735 ，大於0 . 3的溫域差達到46 。
  13. Electrochemical measurements show that specific capacitance of single electrode is increased by 15 % and its impedance is only tens of m

    雙氫氧化物經水熱處理后單電極比容量提高了15 ，達460f4 ，電極內阻僅數十毫歐姆。
  14. The calculation program using the matlab has been worked out to get the numerical solutions of the proposed models. the experiment has first been conducted in the laboratory to get the fundamentals thermal and moisture properties ( such as materials density, specific heat capacity and thermal conductivity ) and also the material moisture absorption isotherms of adobe building materials. the methods of measuring the surface mass transfer coefficient and material moisture content have been proposed

    首次對生土建築材料物性參數進行了實驗測試，得到了常用生土建築材料的密度、比熱和導熱系數等參數值，得到了生土建築圍護結構的等溫吸濕平衡曲線的擬合函數關系式；此外，研究了生土建築圍護結構表面質交換系數實驗測定方法，探索了利用電阻率測量生土建築圍護的安窪築科技人學博十學位論文結構內部含濕量的測試方法。
  15. The result of the calculation for tip clearance is reasonable when it is compared with theory. two ways are put forward for convention of dimension of the turbine components from high temperature to low one, which is related with tip clearance, a simple example is used to illuminate that the two ways are useful, using the method of design optimization, axiisk and a blade of a certain turhine is analysed, it showes that the method of design optimization is feasible to be used for convertion of dimension of the turbine components. finally, ansys software is used to analyzed the variation of tip clearance with the method of cyclic symmetry analysis when engine works under the conditions of temperature and rotational speed, am using a new method to deal with thermal contact resistance in the calculation

    本文完善了計算渦輪葉尖間隙的簡化演算法程序，增加了程序的計算功能，並將其應用於某高壓渦輪進行葉尖間隙分析，所得結果與理論結果進行了對比，得出修改後的程序用於葉尖間隙計算是合理的；同時提出了與葉尖間隙相關的渦輪典型部件的冷、熱態的尺寸兩種換算方法，使用優化設計的方法進行了實例分析，說明了所提出的計算方法是可行的；最後應用ansys有限元軟體利用循環對稱的方法分析了某型發動機高壓渦輪在溫度場及離心力作用下的葉尖間隙在發動機工作過程中變化情況，並分析了計算中的接觸熱阻的處理問題。
  16. The thermal - wet comfort proprties of textiles under the conditions that the environment temperature is higher than that of human body ( called “ reverse temperature field ” ) are examined in this paper. four quanties ( i. e. equivalent thermal resistance, thermal resistance, resistance to water vapour transmission and air permeability ) were suggested as the physical indexes of thermal - wet comfort properties of textiles under this condition. their special meanings under this condition were explained also. the colthing microclimate testing meter was used to determine the indexes of seven different kinds of textiles. the statistical analysis was applied to analyse the relationship between these indexes and the results from wearing - clothing test. some elementary results were obtained

    研究了在環境溫度高於人體體表溫度（稱逆溫差）條件下，服裝用織物的熱濕舒適性能，提出使用當量熱阻、熱阻、濕阻及透氣率作為在此條件下織物的熱濕舒適性物理指標，指出了在此條件下其特殊含義.並且用織物微氣候儀測試了此條件下7種織物的熱濕舒適性指標，與對比穿著試驗的結果進行了分析，得出了一些初步規律
  17. After controlling indexes of the heat preservation and controlling indexes of the energy conservation for building envelop ( root and walls ) in indoor heating condition is given, by means of the interrelated principle between windows and walls the controlling indexes of heat preservation and the controlling indexes at energy conservation for building envelop ( windows ) in indoor heating condition can be determined directly

    摘要該文在室內採暖條件下圍護結構（墻與屋頂）保溫控制指標已確定的基礎上，依據窗墻相關性原理所導出的同一方向窗的傳熱阻與墻的傳熱阻相關性系數（它隨窗墻面積比不同而變化）可直接求出在同一室內熱環境控制條件下窗的保溫、節能控制指標，使保溫控制與節能控制設計更加科學、簡單。
  18. The total surface area as calculated using the fouling resistances in table 1 shall be at least 10 % greater than that calculated using the clean overall transfer rate

    用表1中的污垢熱阻計算出的總表面面積比用? ?總傳熱速率計算出的總表面面積至少大10 % 。
  19. Compared with water swellable gels that are commonly used in china at present, the thermal expansion gel has many obvious advantages

    與目前國內普通使用的遇水膨脹油膏相比，熱膨脹阻水油膏具有明顯的優勢。
  20. Pin diode used as thermo sensor and heating component in this method, low frequency pulse power amplifier is used to substitute rf power in thermo - resistance measurement, and pulse wide compensation is used in dissipation measurement, then equipment require reduced and flexible of equipment rising

    該方法以pin二極體作為感溫元件和發熱元件，採用功率脈沖源來代替射頻功率放大器對器件進行加熱進行熱阻測試，使用占空比補償法進行功耗測試，大大降低了設備要求，提高了測試設備的通用性。
分享友人
分享到 Line

分享到臉書