比較儀校準 的英文怎麼說
中文拼音 [bǐjiàoyíjiàozhǔn]
比較儀校準
英文
gauge setting- 比 : Ⅰ動詞1 (比較; 較量高下、 長短、距離、好壞等) compare; compete; contrast; match; emulate 2 (比...
- 較 : Ⅰ動詞1 (比較) compare 2 [書面語] (計較) dispute Ⅱ副詞(比較) comparatively; relatively; fair...
- 儀 : 名詞1 (人的外表) appearance; bearing 2 (禮節; 儀式) ceremony; rite 3 (禮物)present; gift 4 ...
- 校 : 校名詞1. (學校) school 2. (校官) field officer3. (姓氏) a surname
- 準 : Ⅰ名詞1 (標準) standard; guideline; criterion; norm 2 (目標) aim; target Ⅱ動詞1 (依據; 依照)...
- 比較 : 1 (對比) compare; compare with; contrast; parallel (with); comparison; by comparison; in comp...
-
Calibration specification for base circle pitch comparator
基圓齒距比較儀校準規范Calibration specification for hand - hold pitch comparator
手持式齒距比較儀校準規范Calibration specification for optical comparators for angle measurements
光學測角比較儀校準規范Preparation of steel substrates before application of paints and related products - surface roughness characteristics of blast - cleaned steel substrates - method for the calibration of iso surface profile comparators and for the determination of surface profile - stylus instrument procedure
塗塗料和有關產品前鋼基的制備.噴丸處理鋼基體的表面粗糙度.第4部分: iso表面輪廓比較儀的校準方法和表面輪廓的測定方法.觸針儀法Preparation of steel substrates before application of paints and related products. surface roughness characteristics of blast - cleaned steel substrates. part 4 : method for the calibration of iso surface profile comparators and for the determination of surface profile. stylus instrument procedure
塗料和有關產品使用前鋼基片的制備.噴丸處理鋼基片的表面粗糙度特性.第4部分: iso表剖面比較儀的校準方法和表剖面的測定方法.觸針儀器的程序1 calibration the comparison of a measurement standard of instrument of known accuracy with another standard of instrument to detect, correlate, eliminate by adjustment, and report any variation in the accuracy of the item being compared
調校把一部己知其準確度的儀器的量度標準與另一儀器的標準作比較,來檢查、連系、更正並消除及報告比較專案的誤差。Comparison analysis and experiments show that the calibration instrument can meet the need of laser speedometer calibration because of its wide calibration range, high repeatability and universal performance
經各種校準方法的比較分析和校準試驗驗證,說明裝置校準范圍寬、重復性好、通用性好,可以滿足激光測速儀的校準需求。The multi - port measurement system has the widespread use in microwave measurement, the measurement of multi - port device with two - port vector network analyzer ( vna ) is researched. this paper analyzes the commonly used error models and calibration methods of vna, program a trl calibration procedure for two - port vna, and compare the tested data with the data from vna. the comparison show that the programmed trl calibration procedure is in the same accuracy as the vna
本文討論了兩埠矢量網路分析儀常用的誤差模型和校準方法,編制了兩埠矢量網路分析儀基於trl校準法的校準程序,並把校準后的測量結果和矢量網路分析儀校準后的測量數據做了比較,比較結果說明編制的trl校準程序校準效果和矢量網路分析儀校準的效果相同。Vakuum technology ; standard method for vacuum gauge calibration by direct comparison with a reference vaccum gauge, ionization vacuum gauge
真空技術.用參比測量儀直接比較校準真空計的標準方法Preparation of steel substrates before application of paints and related products - surface roughness characteristics of blast - cleaned steel substrates - method for the calibration of iso surface profile comparators and for the determination of surface profile - focusing microscope procedure
塗料和有關產品使用前的鋼基體的準備.噴丸處理的鋼基體的表面粗糙度. iso表面輪廓比較儀的校準方法和表面輪廓的測定方法Preparation of steel substrates before application of paints and related products. surface roughness characteristics of blast - cleaned steel substrates. part 3 : method for the calibration of iso surface profile comparators and for the determination of surface profile. focusing microscope procedure
塗料和有關產品使用前鋼基片的制備.噴丸處理鋼基片的表面粗糙度特性.第3部分: iso表剖面比較儀的校準方法和表剖面的測定方法.顯微鏡的調焦程序This can be achieved once gps timing synchronization is ready
各觀測站之間的儀器需先互相校準,以求精確比較時間數據。分享友人