毛邊 的英文怎麼說
中文拼音 [máobiān]
毛邊
英文
trimmings; flash; rough selvedge; fringed; [印刷] bolts; deckle edge (紙)毛邊紙 writing paper made from bamboo-
Leaves leathery, oblong, 7 - 13 cm long, base cuneate, glossy above, glabrous on both surfaces, margin sparsely and obtusely dentate ; petiole 1 cm long
葉革質,長圓形,長7 - 13厘米,寬2 - 4厘米,先端銳尖,基部楔形,上面發亮,無毛,邊緣有疏鈍齒;葉柄長1厘米。Leaves thickly leathery, obovate - elliptic to elliptic, 8 - 12 cm long, 4 - 5 cm wide, apex acute, base cuneate, glabrous, serrulate ; petiole 0. 6 - 1 cm long
葉厚革質,倒卵狀橢圓形至橢圓形,長8 - 12厘米,寬4 - 5厘米,先端短尖,基部楔形,無毛,邊緣有細鈍齒;葉柄長0 . 6 - 1厘米。Trimmed sizes of paper according to din 476 ; examples for application of the a series
按din 476對紙張的切毛邊后實際尺寸. a系列的應用示According to the structure of the final forging die, the flash groove is studied and coded into a separate sub - function. in order to split the upper and under dies, a sheet body of the separating surface is coded into a sub - function
根據鍛模設計要求,研究了分模面、毛邊槽的設計並編制了相應模塊;研究了鍛模參數的計算和鍛模實體的生成。Rough edges must be lapped over
毛邊必須折疊起來。Leg opening : finished with 1 x 1 rib so as to allow good elasticity. no raw edges shall be exposed
褲腳開口:成品用1 * 1羅紋收口以使褲腳達到好的彈性。不能有毛邊外露。In ragged shorts and bare feet they come from across the country to set up the festival.
他們穿著毛邊短褲,赤著腳從全國各地來到這里組織這個節日的各種活動。Be suitable for trimming edge for double color sole
適用於雙色鞋底之毛邊修削。A neck with bolts, " nurse were losin him, check the pulse !
毛邊脖子, 「護士他正在離開我們,檢查他的脈搏! 」Number of teeth : 17 inch
數: 20寸無毛邊特殊鋸Unedged sawn timber
毛邊鋸材Pants, such as blue jeans, made into shorts by cutting off part of the legs
毛邊短褲長褲,如藍布牛仔褲,通過截去褲腿的一部分而製成的短褲High grinding efficiency, excellent durability and surface roughness. carbo tzujan industrial co., ltd
等等之修飾細磨精磨加工或毛邊處理。No burr, flash, scratch, flow mark, bright speck, shrinkage defects etc on the surface of product
外觀表面不可有毛邊、刮痕、流痕、亮痕、縮水等不良現象Range of use : cz2. 5 air shovel is used for clearing slag by electric welding, beveling groove. it also can do some shovelling and cutting on steel cast
使用范圍: cz2 . 5型氣才鏟適用於電焊去渣、去毛邊、去坡口,也可在鋼結物體、鑄件上進行少量鏟削。Second defect : including scrape, burrs, rust of the face and the quality of electroplated
次要缺失:指刮痕、毛邊、電鍍、板面銹蝕、水痕、五彩顏色. .等。According to the requirement of die designing, the die parting face and the gutter is designed. by boolean calculation, the blocker, finisher, cut - off die and stripper are generated
根據鍛模設計要求,設計了分模面、毛邊槽,通過布爾運算,生成了預鍛模、終鍛模、切邊模實體和卸料板。Step3 inject remain 1 / 3 of product. according to product molding speed and pressure lower than that of step2 to preent flash speed and pressure should decrease but it can ' t shot short
第三段是注射餘下的1 / 3段,其速度和壓力根據產品的需要,一般是小於第二段,速度和壓力存在於一個往下降的過程.主要是為了防止產品毛邊的產生,但同時又必須把產品充填飽滿Step3 inject remain 1 / 3 of product. according to product molding speed and pressure lower than that of step2 to prevent flash speed and pressure should decrease but it can ' t shot short
第三段是注射餘下的1 / 3段,其速度和壓力根據產品的需要,一般是小於第二段,速度和壓力存在於一個往下降的過程.主要是為了防止產品毛邊的產生,但同時又必須把產品充填飽滿When the pressure inside the mold cavity is too great, the mold opening force is greater than its clamping force. then, the mold will be forced to open and cause burr overflow
當塑料在模腔內的壓力太大,其分模力大於鎖模力,因而迫開工模,就會產生毛邊。分享友人