氣門凸輪 的英文怎麼說
中文拼音 [qìméntūlún]
氣門凸輪
英文
valve cam-
The valve lifter, a round cylinder, rides on the cam.
氣門挺桿為一圓筒體,坐落在凸輪上。The value-opening mechanism includes a valve lifter and a cam on a camshaft.
一套氣門開啟機構包括一個氣門挺桿和一個在凸輪軸上的凸輪。Auto parts : fuel injection system ( valve follower, plunger piston and fuel injection needle, etc. ), power train ( gear, rolling bearing etc. ), piston parts ( packing ring, gudgeon pin etc. ), cam shaft parts ( pin, bush, oscillation beam and some hydraulic components etc. ), others ( gate lock, accouterment etc. )
汽車零部件:燃料噴射系統(氣門挺桿) 、柱塞、噴油針等) 、動力傳動系統(齒輪、滾動軸承等) 、活塞部件(活塞環、活塞銷等) 、凸輪軸部件(銷、襯套、搖臂及部分液壓元件等)和其他部件(如門鎖、內飾等) 。As the camshaft continues to rotate, the high spot moves way from the valve mechanism
因為凸輪軸繼續旋轉,凸輪軸上的凸起部分離開氣門裝置。As the camshaft rotates, the lobe, or high spot of the cam, pushes against parts connected to the stem of the valve
當凸輪軸旋轉時,凸輪凸起的或者高點的位置,推動氣門座。Chapter 6, according to the certain motorcycle, it describes structural radiation yawp, rolling bearing, piston whack, yawp of matching gas of valve cam, gear mesh yawp, burning yawp and the yawp of exhaust and inhaust in details
第六章介紹了對具體摩托車的結構輻射噪聲、滾動軸承、活塞敲擊、氣門凸輪配氣機構噪聲、齒輪嚙合噪聲、燃燒噪聲、進、排氣噪聲進行了全面分析。It solved successfully long - term existent issues in pneumatic speed limiters of high idle speed, large power loss, and swinging of speed at home by means of designing the brand - new - in - structure valve - located device ? am - spring mechanism
由於設計了結構新穎的閥門定位裝置? ?凸輪-彈簧機構,解決了國內現有氣動式限速器長期存在的空載轉速高,功率損失大,游車等問題。Some high - performance engines have two separate camshafts, one for each set of inlet and exhaust valves
一些高性能發動機有兩個單獨的凸輪軸,分別負責開關進氣門和排氣門。While according to dynamics correction method, the valve displacement curve has to be design, which can be acquired by boundary condition and calculation method. then by dynamics analysis, the tappet displacement curve equation can be obtained based on the dynamics differential equation. thus, the design of cam profile can be carried out based on the tappet displacement curve equation
按照動態設計的動力學修正方法進行設計時,又得先進行氣門升程曲線的設計,利用一定的邊界條件和計算方法得到氣門確定的運動規律,再通過動力學分析,根據建立的動力學微分方程,經過計算得到挺柱的升程曲線方程,至此,就可以根據挺柱的升程曲線進行凸輪輪廓曲線的設計。The air inlet noise is related to designing factors like the air inlet mode, the inlet valve structure, the cylinder diameter as well as the cam curve
進氣噪聲與發動機的進氣方式、進氣門結構、缸徑、凸輪型線等設計因素有關。We go in for producing chilled casting camshafts, nodular casting camshafts, high chrome alloy and copper chrome valve seat processing
專業從事冷激鑄鐵、球墨鑄鐵凸輪軸和高鉻合金、銅鉻合金氣門座加工。Da traders specializes in accessory, battery, bolt and nut, brake shoe, cable camshaft, clutch and parts, c v joint, cylinders, fastener, fuel system, horn, ignition coil, lamp, mirror, motorcycle parts, oil seal, piston / ring / pin, relay, shock oxygen, shock absorber, sleeve, spark plug, starter, valve / guide / seat, wheel hub bearing / unit
該貿易公司主營螺栓和螺母,火花塞,輪轂軸承,附件,電池,剎車蹄,線束,凸輪軸,離合器,萬向節,喇叭,點火線圈,車燈,車鏡,摩托車配件,油封,活塞,活塞環,繼電器,減震器, ,起動器,氣門座圈,氣門導管。To transfer the motion of the cam upward to the valve, additional parts are needed
為了將凸輪的運動傳給氣門需要一些附屬裝置。This device is an important part in valve driving mechanism, it works according to the movement rule of cam to ensure the exhaust port open and close correctly, so that it can make the diesel engine running normally
該推桿裝置是氣門驅動機構中的重要部件,它按照凸輪的運動規律進行工作,來完成進排氣門的正確開啟和關閉,從而使柴油機正常運行。分享友人