氣體射入 的英文怎麼說
中文拼音 [qìtǐshèrù]
氣體射入
英文
gas injection-
The wastewater samples is transmitted by an air-operated aspirator to the liquid injection valve.
用氣動吸引器將廢水試樣送入液體注射閥。Some gas - sensitive test to deoxidizing gas have carried out based on tio _ 2 films by sputtering and doped some impurity. the experimental results showed that tio _ 2 films have different electron injecting principle and reactive mechanism, the behaviors of gas - sensor for hydrogen and ethanol manifest dissimilitude. this is due to that the oxygen vacancies were compensated by the impurity
用濺射制備的薄膜摻入部分雜質對還原性氣體進行氣敏測試，發現tio _ 2薄膜對酒精氣體和氫氣有不同的反應機制和電子注入機理，氣敏特性也表現出不同，而雜質的引入反而降低了tio _ 2薄膜的敏感性，可能是由於雜質對氧空位的補償所引起。The feasibility that kaufman ion source is applied in reactive ion beam etching is discussed. etching characteristics of materials, including pr, cr, quartz, are investigated. the etch rate and mechanisms of such materials are measured and analyzed as a function of ion energy, ion beam density and ion incidence angle in pure ar and chf3, respectively. the etch rate has shown a square root dependence on variation versus
深入研究了光刻膠、鉻薄膜、石英等光學材料離子束刻蝕特性，分別以ar氣和chf3為工作氣體，研究光刻膠、鉻薄膜、石英等的刻蝕速率隨離子能量，束流密度和離子入射角度的變化關系，得到刻蝕速率與影響因素的擬合方程，為掩模的製作工藝路線提供了實驗依據和理論指導。Surprisingly, the results indicate that most of the energy released by the infalling gas goes, not into an outpouring of light as is observed in many active galactic nuclei, but into jets of high - energy particles
令人吃驚的是，結果表明，與大多數活動星系核不同，下落氣體釋放的大部分能量並沒有作為光輻射傾瀉而出，卻是注入到了高能粒子噴流中。By analyzing the differentiae of the total cross sections ( tcs ), the differential cross sections ( dcs ), the partial wave cross sections ( pcs ), the change patterns of the cross sections and the influence on the cross sections because of the var iations in the mass of systems and the relative kinetic energy of incoming atoms for symmetric isotopically substituted systems he, ne, ar, kr, xe - h2, d2, t2 have been obtained. in this paper, we use the tang - toennies potential model for the inertia gas atoms - h2 systems, the murrell - sorbie potential surface with five parameters for the molecules h2, d2, t2. for the inertia gas atoms - d2, t2 systems, we use the same potential surface with the inertia gas atoms - h2 systems
通過分析he 、 ne 、 ar 、 kr 、 xe ? h _ 2 、 d _ 2 、 t _ 2各碰撞體系在總截面、微分截面和分波截面等方面的差異，總結出在h _ 2分子的對稱同位素替代情形下惰性氣體原子與h _ 2分子體系碰撞截面的變化規律；通過比較he 、 ne 、 ar 、 kr 、 xe ? h _ 2 、 d _ 2 、 t _ 2各體系在碰撞總截面、微分截面、分波截面等方面的不同，詳細討論了同位素替代碰撞體系中體系約化質量及入射原子的相對碰撞能量的變化對碰撞截面的影響，得出了這種影響的規律性。The impact broke open a heat panel on the wing, which allowed superheated gases to get inside the structure as columbia soared through the skies for landing 16 days later
一塊泡沫擊穿了機翼的隔熱板，使得熱氣流進入機體內部，導致哥倫比亞號在發射升空之後不久，在德克薩斯州上空解體。( 5 ) the intensity and s / b of libs are investigated in detail at the different buffer gas, gas pressure, and laser power. the results show that under the 120 mj laser energy, for ar the best s / b is at 200 torr pressure, but for air at 100 torr and he at 300 torr. duration of atomic spectra in ar is longer than that in air
（ 5 ）實驗測定了不同的緩沖氣體和氣壓以及不同的入射激光脈沖能量對原子譜線強度和背景光的影響，結果顯示在氬氣環境下，當氣壓約為200torr 、激光的能量約為120mj時， libs的s b最大；在空氣和氦氣中獲得最佳s b時的氣壓約分別為100torr和300torr ；原子譜線在氮氣環境中持續的時間要比在空氣中持續的時間長。The results of simulations are : i ) energies of the incident ions to the target are determined mainly by the voltage across the cathode sheath, with a majority of ions " energy vary around the sheath voltage ; ions nearly normally bombard the target ; ions mainly locate above the sputtering holes because of the influence of the magnetic field, and the incident ions mainly come from the region ; the ions undergo several collisions during transportation, but that do n ' t matter much
主要模擬結果有： ? ）入射離子到達靶面時的能量主要受到了射頻輝光放電中陰極殼層西北工業大學碩士學位論文李陽平電壓的影響，大部分離子的入射能量在陰極殼層電壓值附近，離子濺射時接近於垂直入射;射頻輝光放電受到陰極磁場的影響，等離子體中的離子主要集中在靶面濺射坑的上方，且入射離子主要來自這個區域;入射離子在輸運過程中和背景氣體分子有少量的碰撞，但影響不太大。Material is ejected into the crushing chamber by means of high speed ejection flow formed by high - pressure air through charging ejector, and the crushing nozzles outside ejects high - speed airflow into the crushing chamber at certain direction, making the materials severely collided and fractionated, and thus crushed
該機是靠高壓氣體通過加料噴射器所形成的高速射流，使粉碎原料被射入料碎室，粉碎室外圍的粉碎噴嘴，有方向性的向粉碎室噴射高速氣流，使物料間產生激烈的碰撞，磨擦而獲得粉碎。The photochemical properties and the analytical performances of the rtp probe were studied by using a gas flow - injection analysis ( gfia ) system, which incorporated a convenient exponential dilution chamber for gas sample introduction
結合氣體流動注射分析技術（ gfia ） ，利用一指數稀釋瓶引入樣品，研究了該傳感體系的光化學特性和分析特性。Abstract : a new method of desulphurisation of hot metal by immersion is developed by immersing the steel tube filled with desulphurisation powder and propellant into molten iron. the desulphurisation powder is injected into molten iron by pressure produced by propellant decomposing when the steel tube is immersed into molten iron. feasibility of the technology of desulphurisation is discussed in theory
文摘:提出用裝有噴吹劑和脫硫劑混合物的鋼管插入鐵水中，利用噴吹劑受熱分解產生氣體形成的壓力將脫硫劑噴射到鐵水中進行鐵水爐外脫硫的一種新方法熱浸鐵水脫硫法，並從理論上對該法進行了可行性分析A new method of desulphurisation of hot metal by immersion is developed by immersing the steel tube filled with desulphurisation powder and propellant into molten iron. the desulphurisation powder is injected into molten iron by pressure produced by propellant decomposing when the steel tube is immersed into molten iron. feasibility of the technology of desulphurisation is discussed in theory
提出用裝有噴吹劑和脫硫劑混合物的鋼管插入鐵水中，利用噴吹劑受熱分解產生氣體形成的壓力將脫硫劑噴射到鐵水中進行鐵水爐外脫硫的一種新方法熱浸鐵水脫硫法，並從理論上對該法進行了可行性分析The properties of cn thin films such as their morphology, component, crystal structure and the bonding structure and the relation between those properties and the gas - phase reaction parameters were discussed, showing that the deposition of p - c3n4 thin film is the compete result of various reaction processes in the dynamics balance conditions ; the process of cn films depo sition is diagnosed in situ through the optical emission spectra technique, the effects of experimental parameters on the concentration of the precursors and the gas - phase reactions in the plasma have been obtained ; the main reaction precursors for film deposition identified ; the relation between the characteristics of cn thin films and the reaction process in the plasma is analyzed. the cn thin films deposition under different substrate temperatures in high pressure pe - pld shows that the si atom of the substrate has participated the cn films growth process, based on this the growth mode of cn thin films on the si substrate is proposed. the further experiment of cn thin films deposition on si substrate scratched by diamond as well as covered with fe catalyzer has been attempted, which indicates that changing the dynamics conditions of the surface reaction can alter the growth characteristic of the cn thin films and can enhance obviously the films growth rate
採用pld技術進行了碳氮化合物薄膜沉積，得到了含氮量為21at的cn薄膜；研究了襯底溫度和反應氣體壓強對薄膜結構特性的影響，給出了cn薄膜中n含量較小、 sp ~ 3鍵合結構成分較少和薄膜中僅含有局域cn晶體的原因；引入脈沖輝光放電等離子體增強pld的氣相反應，給出了提高薄膜晶態sp ~ 3鍵合結構成分和薄膜的含n量可行性途徑；應用pe - cvd技術以ch _ 4 + n _ 2為反應氣體並引入輔助氣體h _ 2 ，得到了含n量為56at的晶態cn薄膜；探討了cn薄膜形貌、成分、晶體結構、價鍵狀態等特性及其與氣體壓強和放電電流的關系，證明了- c _ 3n _ 4薄膜沉積為滿足動力學平衡條件的各種反應過程的競爭結果；採用光學發射譜技術對cn薄膜生長過程進行了實時診斷，得到了實驗參量對等離子體中活性粒子相對濃度和氣相反應過程的影響規律，給出了cn薄膜沉積的主要反應前驅物，揭示了cn薄膜特性和等離子體內反應過程之間的聯系；採用高氣壓pe - pld技術研究了不同襯底溫度條件下cn化合物薄膜的結構特性，揭示了si原子對薄膜生長過程的影響，給出了si基表面碳氮薄膜的生長模式；在金剛石研磨和催化劑fe處理的si襯底上進行cn薄膜沉積，證明了通過控制材料表面動力學條件可以改變碳氮薄膜結構特性，並可顯著提高晶態碳氮材料的生長速率。Hazardous gas - no entry when flashing
氣體放射中危險禁止進入The explosive mixture of the petrol engine is provided by a carburettor, but in the case of the diesel engine the supply is effected by an injection or jerk pump which forces a shot of fuel into each cylinder in turn according to the correct firing sequence
翻譯：汽油發動機由一個化油器輸送可燃混合氣體，而柴油發動機，由一個噴射泵或柱塞式燃油泵實現燃油供應，此泵根據正確的點火順序把少量燃油依次壓入每個汽缸。Theory predicts that gas falling into these monsters will radiate about 10 percent of its intrinsic energy, sufficient to generate a beacon that can be detected on the other side of the universe
理論預測，掉入這些怪物之中的氣體大約會輻射出內在能量的10 % ，足夠產生在宇宙的另一端都偵測得到信號燈。Gas analysis - preparation of calibration gas mixtures using dynamic volumetric methods - continuous syringe injection method
氣體分析.用動態容量法制備標定用混合氣體.持續噴射器注入法It is concluded that for cvd method the cubic phase content and adhesion are highly effected by the crystal lattice mismatch between c - bn and substrate materials, however, for sputter method the crystal lattice mismatch between c - bn and substrate materials affects the quality of c - bn thin films very little. 5 n - type doping of bn thin films and preparing of bn ( n - type ) / si ( p - type ) heterojunctions adding s into the mixture of argon and nitrogen used as working gas, we sputtered 1ibn target to deposit bn thin films so as to study the n - type doping of bn thin films, and bn ( n - type ) / si ( p - type ) heterojunctions were prepared
5實現了氮化硼薄膜的n型摻雜，成功制備出bn型）乃…型）異質結並且首次系統研究了其卜v和cv特性我們用射頻濺射法濺射六角氨化硼靶，在工作氣體氮和氮中混入s ，沉積氮化硼薄膜，以研究氮化硼薄膜的n型摻雜，並得到bnh型）侶i …型）異質結。Data from existing x - ray satellites that show images of gas whizzing about black holes at close to the speed of light hint that time slows as the gas plunges into the zone from which escape is impossible
從現有的x射線衛星傳回的數據顯示，氣體以接近光速的速度呼嘯著被吸入黑洞，這暗示當氣體進入這個不可逃逸的空間時，時間慢了下來。Particles in the star move around rapidly due to high temperature creating a high gas pressure. together with the radiation pressure generated by the photons, they exert pressure pushing outward to balance gravity s inward pull. then, a star becomes stable and now enters the main sequence phase
恆星內部所產生的高溫，會令粒子急劇運動，產生向外的氣體壓力，再加上光子的輻射壓力抵消掉向內的引力，令恆星保持穩定，進入主序星階段。分享友人