氣體裂化器 的英文怎麼說
中文拼音 [qìtǐlièhuàqì]
氣體裂化器
英文
gas converter-
This paper aims at the characteristics of thermal response of lpg vesse1 under high temperatue, conjoining the project of " study on transportation safety early - wdring system of lpg dangerous goods " supported by transportation departinen of china and the project of " mechanism study and numerical simulation of the explosion of lpg vessel " supported by science foundation of hubei province. the interdisciplinary research has been done among temperature field distribution of lpg vessel under flame surroundings, intensity calculation, crack propagation predication and mechanism of explosive accident, etc. three parts are analyzed and discussed
本文針對高溫環境下液化氣壓力容器的熱響應特性問題，結合交通部重點科技項目「液化氣體類危險品運輸安全預警系統的研究」和湖北省自然科學基金項目「液化氣容器爆炸機理研究及數值模擬」 ，對在火焰包圍下的液化氣壓力容器的溫度場分佈、強度計算、裂紋擴展預測以及爆炸事故機理等方面開展了多學科的交叉研究。By using catalyst a, the catalytic splitting decomposition of waste rubber tyre was developed. the splitting gas, gasoline, diesel oil, heavy oil and carbon black were obtained by this process. by inspecting, the qualities of the products all accorded with the using demands
一種先進的廢舊橡膠輪胎催化裂解處理技術被開發，通過反應器的廢橡膠輪胎顆粒被催化裂解為裂化氣、汽油餾分、柴油餾分和重油餾分，殘余的固體可加工為炭黑，各種產品經檢測，其理化指標及使用性能均達到用戶要求。A two - dimensional model is proposed for simulation of gas phase cracking of 1, 2 - dichloroethane ( edc ) to produce vinyl chloride monomer ( vcm ) in tubular reactor furnace, in which side reaction of coke precursor formation is taken into consideration
摘要建立了二氯乙烷在管式反應器中進行氣相熱裂解的二維模型，模型考慮了二氯乙烷熱解生成氯乙烯的主反應和生成焦前體的副反應以及氣體密度變化對裂解反應的影響。The paper mainly discussed the reasons of stress from liquid ammonia pressure vessel causing crack through examing data and experimental results and analysing relevant referential documents and materials, taking 1200 ammonia vessel ' s crack and leaking in a certain fertilization company as an example : there existed remaining welding, stress in the equipment ; there existed a stress decaying surrounding, i. e., moisture 0. 2 %, and temperature > - 5 with o2 or co2 inside ; the higher the intensity of raw materials, more possible it was to have stress decaying crack
摘要以某化肥公司1200氨冷器殼體開裂泄漏的失效分析為例，通過對檢驗數據和結果及有關文獻資料的分析研究，探究了液氨介質壓力容器產生應力腐蝕裂紋的原因：設備中存在較高的焊接殘余應力；液氨介質具備應力腐蝕環境，即含水量0 . 2 % ，且有空氣（ o2或co2 ）污染（或摻入） ，使用溫度高於零下5 ；母材強度越高，應力腐蝕裂紋產生的傾向就越大。The research of this paper includes : ? high - speed photography and flash x - ray radiography are both used to capture the process of al shell ' s great deformation under low pressure. front illuminations are used to get the development of the fracture on the al shell. the relative energy release is analyzed from overpressure curves measured with some sensors
本文的研究內容主要包括： ?在受試炸藥經歷低應力大變形過程的susan試驗中，同時採用高速攝影、閃光x射線照相對彈體的撞靶過程進行了拍攝，得到了殼體膨脹變形過程圖像，並使用前照明技術觀察到了鋁殼表面產生的裂紋及其發展變化過程；從壓力傳感器測量的空氣沖擊波超壓曲線，獲得反應釋放總能。Model calculation indicated that the residence time of particles differed greatly from that of gas product, so product distribution from pyrolysis was significantly affected
模型的計算結果表明，原料粒子和產物氣體在反應器內的停留時間有較大的區別，其變化情況對裂解產物的分佈有很大影響。Three - dimensional gas flow field in the new vortex quick separation system with an inner component of fcc disengager was simulated based on the reynolds stress model ( rsm ) provided by cfx
摘要用cfx軟體對催化裂化沉降器新型旋流快分器的氣相流場進行了三維模擬，湍流模型採用雷諾應力輸運方程模型。分享友人