汽密接合 的英文怎麼說

中文拼音 [qìmìjiēgě]
汽密接合 英文
steam tight joint
  • 汽 : 名詞1. （由液體或某些固體變成的氣體） vapour2. （水蒸氣） steam
  • 密 : Ⅰ名詞1 （秘密） secret 2 [紡織] （密度） density 3 （姓氏） a surname Ⅱ形容詞1 （距離近; 空隙小）...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 接合 : joint; zygosis; juncture; articulation; concrescent; nexus; coaptation; syndesis; synapsis; meet;...
  1. Results of experiment b demonstrate that a convergence zone of wind vector and water vapour with dense pressure gradient is formed alone the coast after tc ' s outer circulation encountering land, which results in more precipitation

    試驗b的結果顯示，熱帶氣旋外圈環流與陸地接觸後到中心登陸前後，沿海岸線一直存在一條氣壓梯度相對密集的風矢量、水汽輻合帶，引起該處降水增多。
  2. The apsp produced abroad is made by numerical controlled machine tool, which has noise level of 71db ( a ), the apsp produced in our country is made in the method of exploratory which has noise level of 73db ( a ) and 75db ( a ). in order to analyze the influence of stator curve to noise, the author used tri - coordinate measuring instrument to measured exactly the inside surface of stator and got the straddling point coordinate, and made curve fitting by using matlab as language and studied the fitting effect and then worked out the equation of stator transition curve in return seeking, then comparied this method with the standard style and made the conclusion : the equation of atator transiting curve of apsp made by numerical controlled machine tool is close to theorical 5 power curve standard style, but compared with it, the stator transiting curve of apsp produced in exploratory has a major error. combining the testing results of noise, one can know that the qualily of stator transition curve play an importance to t he noise of the pump

    國外生產的汽車動力轉向泵是用數控機床加工的，其噪聲值為71db （ a ） ，國內生產的汽車動力轉向泵是用靠模方法加工的，其噪聲值分別為73db （ a ）和75db （ a ） ，為了分析定子曲線對泵的噪聲的影響，本人用三坐標測量儀對定子內表面進行精密測量，獲得定子內表面的離散點坐標，以matlab語言為工具對離散點進行曲線擬合，觀察擬合效果，然後，用回歸方法求出了定子過渡曲線的方程，並把該方程與理論方程標準型進行了比較，得出如下結論：用數控機床生產的汽車動力轉向泵的定子過渡曲線方程非常接近理論5次曲線標準型，而用靠模方法加工的汽車動力轉向泵的定子過渡曲線與理論5次曲線標準型相比較，則存在著較大的誤差，結合噪聲測試結果可知，定子過渡曲線的優劣，對泵的噪聲大小有著重要的影響。
  3. Take special care not to damage the cylinder block sealing face when removing the plastic dowels

    當移除這塑膠接縫鏍釘時，應特別小心避免損壞汽缸接合之密封面。
分享友人
分享到 Line

分享到臉書