波形刀 的英文怎麼說
中文拼音 [bōxíngdāo]
波形刀
英文
kriss-
On the basis of the theory of fractal geometry, the fractal dimension characters of ae signal at different tool wear states were analyzed, an algorithm was provided to decide the scale range which is necessary to calculate the dimension of non - fully - fractal form. the experiments showed that the fractal dimension of ae signal is slightly effected by the changes of cutting parameters ; the variance of the fractal dimensions, which reflects the geometric characters of ae signals, has the same tendency as that of the flank wear, the monitoring system, which takes the fractal dimension of the ae signal as the feature, can identify the different tool wear states more correctly under different cutting conditions
以分形幾何理論為基礎，對刀具不同磨損階段聲發射信號的分形特徵進行分析.提出了計算非完全分形體信號波形的關聯維數時尺度范圍的確定方法，分析了聲發射信號在刀具磨損過程中分形維數的變化特性.刀具磨損切削實驗數據表明，聲發射信號的分形維數受切削參數變化影響較小；分形維數反映了聲發射信號的幾何特徵，其大小能較好地反映刀具的不同磨損狀態.實驗結果表明，該方法能正確地實時在線監測刀具的不同磨損狀態After analyzed the basic principle of optimized noise reduction on tyre pattern, summarized three approaches to noise reduction. the first is trying to reduce size of single block or socket to reduce noise amplitude on time domain, the second is to adjust stripes sorting order and their interlace value to avoid noise - made by every single block - peak values on time domain overlayed and the last is to adjust ratio of blocks and sockets, ratio of stripe interval and stripe sorting order to avoid noise periodical distribution and abnormal high peak values in some frequency strip
論文第四章分析了輪胎花紋優化降噪的基本原理，總結出三條降噪途徑：在允許范圍內盡量減小單個塊或槽的大小、刻刀槽軟化花紋塊來減小噪聲時域波幅度；調整節距排列順序、花紋條之間的錯位值，使各發聲單元發出的聲壓時域波形的同向峰值錯開，避免同向峰值疊加；調整花紋塊和槽比例、節距比例、節距排列順序，盡量避免周期性分佈，使輪胎所發出的噪聲趨于白噪化，避免某些頻段的異常高峰值。Analysis of experiment for sticking failure mechanism of wave insert
波形刃銑刀片粘結破損試驗分析This kind of switch use the unilateral fin - line as the basic transmission line, the beam lead pin diode of alpha co. ltd is the control element, there is two diodes in each channel and they are welded in circuit in parallel connection
本課題主要研究的是毫米波鰭線pin管單刀雙擲開關。該開關採用單側鰭線作為基本傳輸線，控制器件選用alpha公司的梁式引線pin二極體，每路使用兩只，採用並聯形式焊接在電路中。This case illustrates retrocecal appendicitis should be considered as one of the differential diagnoses for earlier surgical intervention if a patient exhibits such atypical clinical manifestations accompanied with an elongated tubule structure of the right abdomen by sonography
所以這個病例揭示我們如果病人有右上腹疼痛且超音波顯示右腹有一長條形管狀結構時，急性闌尾炎應該也要列入臨床診斷的考量之一，以便能及早開刀處置。The difficulty in design microstrip pin sp3t switch is the via hole for grounding. we use both the radial parts and the via hole to get a good result. the fin - line pin switch is fully simulated using full - wave analysis, the parasitic parameter and the circuit assemble need to be considered
微帶結構上過孔微波接地效果的不理想，是微帶單刀三擲開關的難點，本文採用了扇形的微波接地和過孔直流接地結合起來，較好的解決了這一問題。分享友人