注蒸汽壓力 的英文怎麼說

中文拼音 [zhùzhēngqìyālì]
注蒸汽壓力 英文
steam injection pressure
  • 注 : Ⅰ動詞1 （灌入） pour; irrigate 2 （集中） concentrate on; fix on; focus on 3 （用文字來解釋字句）...
  • 蒸 : Ⅰ動詞1. （蒸發） evaporate2. （利用水蒸氣的熱力使食物熟或熱） steam Ⅱ名詞[中醫] （將藥物隔水蒸熟） steaming
  • 汽 : 名詞1. （由液體或某些固體變成的氣體） vapour2. （水蒸氣） steam
  • 壓 : 壓構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 蒸汽 : vapour; reek; breath; steam蒸汽採暖 steam heating; 蒸汽錘 [機械工程] steam hammer; 蒸汽打樁鍾 ste...
  1. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。
  2. Through analyzing the effect of temperature and nitrogen on crude oil viscosity the influences of different nitrogen injection volume and injection modes on steam displacement are contrasted, the mechanism of nitrogen - assisted steam stimulation is clarified, which includes : heat carrying capacity is raised, the saturation of remaining oil is reduced after nitrogen - assisted injection is made ; crude oil flow is enhanced because of nitrogen compression and dispersion and the change of oil flow shape ; water back - production rate is improved by expanding the steam sweep volume and compensating in - situ energy ; steam distillation effect is enhanced

    通過分析溫度、氮氣對原油粘度的影響，對比不同注氮量、不同注入方式等對蒸汽驅油效果的影響，弄清了氮氣輔助蒸汽增產的機理主要表現在：氮氣輔助后增加攜熱能力，降低殘余油飽和度，氮氣的壓縮膨脹作用分散和改變了原油流動形態，增強了原油流動性；擴大蒸汽的波及體積，補充地層能量，提高回採水率，強化蒸汽蒸餾效應。
  3. A treatment method of super - saturation steam for deposited salt in steam turbine is introduced, output of the steam turbine is therefore improved through purge. purification process and attentions are introduced

    摘要介紹了背壓式汽輪機積鹽積垢的處理方法?過飽和蒸汽法，通過清洗使汽輪機的出力率得以提高。介紹了清洗的過程和注意事項。
  4. Leng 43 block was developed in 1993 and since then conventional fracturing conduction, water flooding test, steam soaking were successively carried out, but exposing several inconsistencies such as high decline rate of output, water flooding fingering, low potential of steam soaking etc. among them the physical properties is an important factor that affecting the result of development

    該塊從1993年投入開發以來，先後進行過先期壓裂常規開采、注水開發試驗、蒸汽吞吐開采，但是暴露出常規開采產量遞減快、水驅指進、蒸汽吞吐潛力小等矛盾，其中儲層特徵是影響其開發效果的一個主要因素。
分享友人
分享到 Line

分享到臉書