泵軸 的英文怎麼說

中文拼音 [bèngzhóu]
泵軸 英文
pump spindle
  • 泵 : 名詞（吸入和排出流體的機械） pump
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  1. Driveequipment use active magnet connected - implement to firsthand fix at the axletree of electrical engine, pumproom close completely, via magnetic force coincidence to drive impeller on rotor - assembled to circumgyrate indirectly, it own the trait like tightly structure handsome exterior small bulk laigh noise unfailingly move expediently service using safety and economize etc

    ，驅動裝置採用主動磁鐵聯軸器直接裝在電機軸上，泵室完全封閉，通過磁力偶合間接驅動泵軸上帶磁鐵的葉輪旋轉，具有結構緊湊
  2. Application of demodulated resonance and fuzzy distinguishing technique to fault diagnosis of bearings in drilling pump

    共振解調和模糊識別技術在鉆井泵軸承故障診斷中的應用
  3. Fsb series fluoroplastic alloy pump is composed of pump body, impeller, back cover, seal, support, pump shaft, bearing, coupling, fasten bolt, nut and base plate

    Fsb系列氟塑料合金泵由泵體、葉輪，后蓋，密封性，支架，泵軸，軸承，連軸器，吊緊螺栓，螺母，底板組成。
  4. For motor shafts, the highest stress is at the boundary between the key groove and the ring groove ; the next one is at bottom and terminal of the spline. according to the results, the 17. 4mm shaft is insecurity, the 22. 2mm and 30. 2mm shafts are security

    在軸的安全性上，對17 . 4mm泵軸計算結果是不安全的；對22 . 2mm泵軸計算結果是安全的；對30 . 2mm電機軸計算結果是安全的，而且還有較大的功率輸出空間。
  5. For the 30. 2mm shaft, there are still larger over measure to load. the strength is increased by optimization. for ? 17. 4mm shaft, the strength is increased by enlarge the inner dimension of the spline ; for 30. 2mm shaft, the strength is increased by adjust the structure at the boundary between the key groove and the ring groove, the highest stress of the shaft is at bottom and terminal of the spline after optimization

    其中對17 . 4mm泵軸的優化，通過增大花鍵內徑，提高了花鍵齒底的強度，降低了應力集中點附近的應力；對30 . 2mm電機軸的優化，通過在軸承鍵的環槽端增加倒角，有效降低了該位置的應力集中，使軸的最大應力點從軸承鍵與環槽的交界處轉變到花鍵根部與收尾的交界處，提高了電機軸整體結構強度的合理性。
  6. It is appropriate for measuring end temperature of bearing liner or other works, e. g., push bearing liner of steamer, supporting bearing liner or push bearing liner of electromotor main axis, bearing liner of coal pulverizer, bearing liner of high efficient feed water pump, bearing liner of compression machine and kinds of other objects inpetrochemical plant

    適用於測量軸瓦或其它機件的端面溫度，如：汽輪機推力軸瓦，電機主軸支持瓦推力瓦，磨煤機大瓦和高效給水泵軸瓦石油化工廠壓縮機軸瓦和各種機件物體的表面測量。
  7. Based on the comparison of the restoring features of several common journal dimensions and in accordance with the shaft wearing character of large water pump, the treatment technique applying brush coast and hot spraying was discussed

    摘要在比較幾種常用軸頸尺寸修復特點的基礎上，根據大型水泵軸軸承位磨損特徵， ?述了採用電刷鍍和熱噴塗處理技術修復水泵軸的工藝方法。
  8. Structural design of hydrostatic bearing for the axial force equilibrium of multistage pump

    平衡多級泵軸向力的液體靜壓支承的結構尺寸設計
  9. Hydrostatic bearing can solve the equilibrium problem of axial force of multistage centrifugal pump satisfactorily

    液體靜壓支承技術可以很好地解決多級離心泵軸向力的平衡問題。
  10. Pump shaft is provided with independent supporting point to ensure dependable running of motor bearing

    泵軸有獨立的支撐點，使電機軸承運行可靠。
  11. Diesel engines - fuel injection pumps - tapers for shaft ends and hubs ; identical with iso 6519 : 1993

    柴油機.噴油泵.軸端和轂環的錐度;等同採用iso 6519
  12. Diesel engines - fuel injection pumps - tapers for shaft ends and hubs

    柴油機.噴油泵.軸端和轂盤的錐度
  13. The influence of the eccentricity mass moment, position of mass center and the bearing stiffness to the vibration characteristics of the rotor system is discussed in detail ; 3. to verify the exactness of fem and learn the principle of vibration of dredge pump further, the orbit of the rotor shaft of the pump in the dredger is measured, the measurement results show : the repeat of the orbit of the rotor shaft is very bad when dredge pump is in the dredging mud condition

    模態分析確定了泥泵的振動特性（固有頻率和振型） ；諧響應分析確定了泥泵轉子軸在偏心力的作用下軸截面處的最大響應位移；研究了轉子軸的質心位置、軸承剛度和質量偏心矩對轉子軸振動特性的影響； 3 、採用軸心軌跡法，實船測量了泥泵軸工作時振動響應值。
  14. Research on shaft of gear pump repaired by arc - sprayed 3cr

    13修復齒輪泵軸試驗研究
  15. Paying attention to some issue of sealing of pulp pump

    漿泵軸密封應注意的問題
  16. Technical specifications for mixed and axial flow pumps

    混流泵軸流泵技術條件
  17. Analysis of axial forces balance on 50 chta 6 feedwater pump

    6型給水泵軸向力平衡分析
  18. Analysis of quenching cracks of pump axle

    水泵泵軸淬火裂紋分析
  19. Test methods for centrifugal, mixed flow, axial and regenerative pumps

    離心泵混流泵軸流泵和旋渦泵試驗方法
  20. Hcp pump manufacturer co., ltd

    壓縮機、風扇、泵軸
分享友人
分享到 Line

分享到臉書